Installation guide
3.
Remove
panels
and
set
panels
aside
on
a
covered
surface.
4.
Check
that
grounding
clip
is
attached
to
the
lower
panel.
panel
Grounding
clip
5.
Slide
nut
and
ferrule
onto
tubing.
Copper
tubing
only:
Slide
nut,
then
ferrule,
about
1"
(2.5
cm)
onto
copper
tubing.
NOTE:
To
avoid
vibration
during
operation,
route
the
water
supply
line
so
that
it
does
not
touch
the
dishwasher
base,
frame
or
motor.
6.
Add
90°
elbow
fitting
to
the
water
supply
line.
Connect
the
98"
compression
fitting
to
the
water
supply
line
prior
to
installing
the
unit
into
the
cabinet
opening.
Attach
such
that
the
¥4"
connection
is
facing
upward.
Copper
tubing
only:
Put
the
tubing
into
the
90°
elbow
fitting
as
far
as
it
will
go
(the
copper
tubing
bends
and
kinks
easily).
Slide
the
nut
and
ferrule
forward
and
start
the nut
onto
the
elbow
threads.
Flexible
braided
connection:
Secure
nut
to
elbow
using
¥8"
open
ended
wrench
or
adjustable
wrench.
NOTE:
Do
not use
Teflon®
tape
with
compression
fittings.
7.
Remove
terminal
box
cover.
—
If
you
are direct
wiring:
Install
a
UL
Listed/CSA
Approved
clamp
connector
to
the
terminal
box.
If
using
conduit,
use
a
UL
Listed
/CSA
Approved
strain
relief.
—
If
you
are
installing
a
power
supply
cord
kit,
do
so
now,
following
kit
instructions.
The
power
supply
cord
kit
must
be
UL
Listed
and
marked
for
use
with
dishwashers
(that
is,
Power
Supply
Cord
Kit
Part
Number
4317824).
7®Teflon
is
a
registered
trademark
of
E.l.
Du
Pont
de
Nemours
and
Company.
10
Terminal
cv
box
cover
Pe
ie
PER
\
&
Deeks
ou
Cable
clamp
connector
Dishwasher
wires
8.
Measure
height
of
cabinet
opening
from
underside
of
countertop
to
floor
where
dishwasher
will
be
~~]
—_
installed
(you
need
the
lowest
—
point).
Check
chart
for
that
height
opening.
Put
wheels
in
the
required
position.
—
Vv
[——
Minimum
Wheel
Number
of
cutout
height
|
position
front
fe
g
34"
(86.4
cm)
1
10
341%"
(87
cm)
2
5
34'4"
(87.6
cm)
3 0
dishwasher
to
fit
into
a
337"
(86
cm)
high
cutout,
but the
dishwasher
will
be
more
9.
Turn
both
front
leveler
legs
to
the
same
height.
®
If
the
minimum
cutout
height
is
less
than
34"
(86.4
cm),
the
rear
wheels
can
be
removed
for
additional
clearance.
This
will
allow
the
Front
leg
difficult
to
move
into
position.
If
the
wheels
are
removed,
cover
the
floor
when
moving
the
dishwasher.
If
you
have
built-up
floors
].
Measure
height
of
opening
from
underside
of
countertop
VA
to
built-up
floor.
If
the
height
TF
Countertop
is
at
least
3394"
(85.7
cm),
the
dishwasher
will
fit
into
the
opening
without
modification
to
the
countertop
or
flooring.
2.
Put
wheels
in
position
1
and
turn
the
front
leveler
legs
up
all
the
way.
3.
Add
shims
as
needed
in
the
area
shown
to
bring
dishwasher
up
to
proper
height.
NOTE:
Shims
must
be
securely
attached
to
the
floor
to
keep
them
from
moving
when
the
dishwasher
is
operating.
6"
25/4"
(700m)
(15.2
cm)