Installation guide
Install
custom
door
panel
kit
(on
some
models)
If
installing
a
custom
door
panel
kit,
install
it
now
following
instructions
included
with
kit.
Choose
attachment
option
AWARNING
Excessive
Weight
Hazard
Use
two
or
more
people
to
move
and
install
dishwasher.
Failure
to
do
so
can
result
in
back
or
other
injury.
Using
two
or
more
people,
stand
the
dishwasher
up.
IMPORTANT:
The
dishwasher
must
be
secured
to
the
cabinet.
There
are
two
brackets found
in
the
parts
bag.
Attach
the
brackets
to
the
top
of
the
dishwasher
if
the
countertop
is
wood,
laminate
or
another
similar
surface.
If
your
countertop
is
marble,
granite
or
another
hard
surface,
install
using
Option
#2.
Option
1,
Countertop
attachment
J.
Remove
the
brackets
from
the
package
and
place
in
the
open
slots
on
the
left
and
right-hand
top
of
the
dishwasher
collar
as
shown.
2.
Insert
the
bracket
into
the
slot
on
the
collar.
Using
a
pair
of
pliers,
bend
the
tab
down
to
secure
the
bracket
in
place.
Repeat
this
step
for
the
other
side.
NOTE:
Do
not
attach
the
dishwasher.
This
will
be
done
later.
Option
2,
Dishwasher
with
Stainless
Steel
Tub
Side
Attachment
(for
marble,
granite
or
other
hard
surface
countertops)
J.
Remove
the
brackets
from
the
parts
package.
2.
Break
off
the
end
of
the
bracket
along
the
scored
line.
Score
line
3.
With
another
person
holding
the
dishwasher
to
avoid
it
from
tipping,
open
dishwasher
door,
and
place
towel
over
pump
assembly
and
spray
arm
of
dishwasher.
This
will
stop
screws
from
falling
into
pump
area
when
securing
dishwasher
to
cabinet.
4.
Push
the
plastic
buttons
out
of
the side
of
the
tub.
NOTE:
Save
the
buttons
to
cover
the
holes
after
dishwasher
is
installed.
‘
bE
\
Plastic
button
/
5.
Push
bracket
into
slot
on
the
side
of
dishwasher,
and
bend
tab
in
toward
the
side
of
the
dishwasher
so
that
it
keeps
the
bracket
in
place.
NOTE:
Do
not
attach
the
dishwasher.
This
will
be
done
later.
Bend
“|!
OP
Option
3,
Dishwasher
with
Plastic
Tub
Side
AHtachment
(for
marble,
granite
or
other
hard
surface
countertops)
Order
Mounting
Bracket
Kit
Part
Number
8212560.
Check
door
spring
tension
With
another
person
holding
the
dishwasher
to
keep
it
from
tipping,
open
and
close
the
door
a
few
times.
If
the
door
closes
or
falls
open
under
its
own
weight,
the
door
tension
will
need
to
be
adjusted.
mg
If
the
door
closes
too
quickly,
decrease
the
spring
tension
by
moving
the
spring
end
toward
the
front
of
the
dishwasher.
mg
If
the
door
falls
open,
increase
the
spring
tension
by
moving
the
spring
end
toward
the
back
of
the
dishwasher.
m=
Springs
should
be
in
the
same
notches
on
left
and
right
sides.
Spring
Move
spring
end
Move
dishwasher
into
cabinet
opening
as
Using
two
or
more
people,
stand
the
dishwasher
up.
2.
Grasp
the
sides
of
the
dishwasher
at
the
-——4
edges
of
the
door
panel.
3. Tilt
dishwasher
backward
on
wheels
and
move
dishwasher
close
to
cabinet
opening.
Do
not
push
on
the
front
of
the
panel
or
on
the
console
—
they
may
dent.
4.
If
dishwasher
has
a
power
supply
cord,
insert
power
supply
cord
into
hole
cut
into
cabinet.
If
using direct
wire,
check
that
it
is
on
the
right
front
side
of
opening.
§.
Check
that
water
line
is
on
the
left
side
of
opening
and
drain
hose
is
near
the
center
of
the
hole
in
the
cabinet.
1