Installation guide

ManualsBrandsKenmore ManualsMicrowave Hood ComboOfficial Kenmore microwave

WhatdoI needto installthe

microwavehood?

• Tools, parts & materials 4

• Requirements 5

• Product dimensions 5

WhatdoI needto dobeforeI

installthe microwavehood?

• Preparemicrowave hood

• Preparecabinet opening

The microwave hood is factory set for ventless

(recirculating) operation. To vent through the wall

or roof, changes mustmadeto the venting system.

HowdoI installthe

microwavehood?

• Secure microwave hood

to wall and cabinet

• Connectmicrowavehood

Qu_tengoquehacerpara

instalarla campanadel horno

microondas?

• Instrumentos, piezasy materiales 4

• Requisitos 5

• Dimensiones del producto 5

fnQU_tengoquehacerantesde

sta!arla campanadel horno

de microondas?

• Preparar la campanadel horno de

microondas 10

• Preparar laabertura en el gabinete 12

Lacampana del horno est_ disefiada por la f_brica para

operaci6n sin salida de aire (recirculaci6n). Paraque haya

salida de aire a trav6s de una paredodel cielo raso, deben

hacersecambios al sistema de salida de aire.

_C6mo instalola campanadel

ornodemicroondas?

• Fije la campanadel horno a la

pared o al gabinete 16

• Conecte la campanadel horno 18

Pa_ No.4619-655-95771/8169537 Rev.B

Pa_e No. 4619-655-95771/8169537 Re_ B

Doing so will:

make installation easier.

help you in the future if you havequestions.

help if you have an electrical inspection.

Callyourauthorizeddealer or servicecenter whenyou

havequestionsor needservice. Whenyou call, youwill

needthe microwavehoodmodeland serial numbers.Both

numberscanbefoundon the model/serial rating plate

locatedbehind the microwaveovendoor onthefront

frame ofthe microwaveoven.

Hacedo:

v' hard mds f_cil la instalaci6n.

v' Io ayudar_ en el futuro si tienealguna pregunta.

v' Io ayudar_ si tiene una inspeccion el6ctrica.

Llame a su distribuidorautorizadoo centrode servicio

cuandotenga alguna preguntaonecesiteservicio. Cuando

game, tengaa mano el ndmerodel modelo y el ndmero

de serie de la campanadesalida de aire del homo de

microondas. Ambosndmerosse encuentranen la placa de

clasificacionde modeio/sedeque se encuentradetr_s de

la puertadel homode microondasenei marcodeiantero

del horno2de microondas.

Summary of content (11 pages)

PAGE 1
What do I needto installthe microwavehood? • Tools, parts & materials • Requirements • Product dimensions 4 5 5 What do I needto do beforeI install the microwavehood? • Prepare microwave hood • Prepare cabinet opening 10 12 Howdo I install the microwavehood? 4 5 • Dimensiones del producto 5 fnQU_tengoque hacer antesde sta!ar la campanadel horno de microondas? • Preparar la campana del horno de microondas 10 _C6mo instalola campanadel ornode microondas? 16 18 Doing so will: make installation easie
PAGE 2
Your safety and the safety others is very important. of We have provided many important safety message in this manual and on your appliance. Always read and obey all safety messages. "O "O This is the safety alert symbol. This symbol alerts you to hazards that can kill or hurt you and others. Atl safety messages wilt be preceded by the safety alert symbol and the word "DANGER" or "WARNING". These words mean: Su seguridad y la seguridad de los demds es muy importante.
PAGE 3
continuedfrompage3 iene de lap#gina 3 Tools and materials needed Herramientas y materiales que se necesitan A. B. C. D. E F. 6. H. I. J. K. A. Guantes B. Anteojos protectores C. Cinta de medir D. Ldpiz E. Cinta adhesiva o tachuelas F. Tijeras G. Taladro eldctrico H. Broca de barrena de 3/16° I. Brocas de barrena de 3/8" y 3/4" para madera J. Destornillador de punta plana K. Destornilladores Phillips: No. 2 para prensa de tornillo de cable de alimentaci6n y No.
PAGE 4
Electrical EI6ctricos 3-prong ground plug enohufe de puesta a tierradetres terminales Electrical Shock Hazard j/ power supply cord cablede ground prong terminal para conexibna tierra \ \ alimentaci g-prong ground-type wall receptacle 6n tomacorriente de pared con tres terminales para puesta a tierra Plug into a grounded 3-prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord.
PAGE 5
continuedfrompage7 Roofventing Salida de alre per el cielo raso roof cap caperuzade cieth raso vienede la p_,gina7 Forwall or roofventing methods: Choose between roof venting or wall venting. If the wall exhaust method is chosen, be sure that there is proper clearance within the wall for the exhaust vent. Vent materials neededfor installationare not included.
PAGE 6
Am 1 i © 1 Remove tape and save for future use. Remove contentsfrom inside microwaveoven including turn table, turn table supportand hub. Mounting plate is gray metal plate attached to back of microwave hood. Removethe mounting plate: • Remove two screws @ from top of microwave hood located closest to the front corners. Do not remove screws located towards the center of hood. • Remove front grille ®. Set screws and grille aside. • Pull hook © to releasemounting plate.
PAGE 7
0 Elnlllllll II IIIIIIIllll '1. Disconnectpower supplyto outlet. Desconecteel suministroel6ctrico del tomacorriente de pared, 2. Put on gloves and safety glasses. P6ngaselos guantes y los anteojos protectores. Disconnect and move freestanding range to provide easier access or put a protective cover over a cooktop, Removeall contents from upper cabinet, Desconectey mueva la cocina autoestable para tener f_cil acceso o ponga una cubierta protectora en la encimera.
PAGE 8
Q power supplycord bushing _,e. alojamiento del cord6nde alimentaci6n 10. :_lli continuedfrompage13 ienede la p_gina13 Use a hole drill or key hole saw to cut a 2" diameter hole at shaded area marked "M" on upper cabinet template, Use una broca de barrena o una sierra de calar para hacer un orificio de 2" de di_metro en el _rea sombreada marcada "M" en la plantilla del gabinete superior. Note: Install a power supply cord bushing around hole if cabinet is metal.
PAGE 9
OI Placea washer on each 1/4-20 x 3" bolt and place inside upper cabinet by the 3/8" holes. Ventless or roof venting: Go to Step 3. R Coloque una arandela en cada perno de 1/4-20 x 3" y col6quela dentro del gabinete superior cerca de los orificios de 3/8". Para instalaci6nsin salida de aire o con salida a trav6s del cielo raso:vaya al Paso3. R Wall venting installation: Instalaci6n con salida a trav6s de la pared: Checkthat damper blade _ is on top of tab ®,moves freely, and opens fully.
PAGE 10
Ei Wall venting or recirculatingventing: Go to step 2. 1 Roof-ventinginstallation:The damper MUST fullyopen. Check that damper blade ® is on top of tab ® and moves freely. Note: if possible, fit the damper assembly and vent connector or transition piece together to check that the damper opens fully before making final vent connection. Insert damper assembly through cabinet opening © so that long tab @ slides under the raised edge of damper plate.
PAGE 11
o][o m m m • Checkthat the circuit breaker is not tripped or the house fuse blown. • Checkthat the power supply cord is plugged into the wall outlet. • See the Owner's Manual or Use and Care Guide for troubleshooting checklist. • Verifique que no se haya botado el interruptor de circuito o que no se haya fundido un fusible. • Verifique que el cable de almentaci6n est6 enchufodo en el tomacorriente de pared. • Consulte la seccicable de alimentacinterruptor de circuito o que no se haya fundido un fus.