Use and Care Manual
52
53
DESMONTAJE Y SUSTITUCIÓN
DE LAS PUERTAS DEL REFRIGERADOR
ADVERTENCIA
Riesgo de descargas eléctricas
Antes de retirar la cubierta de la bisagra superior
• Apagar el suministro de agua al refrigerador
• Desconecte el enchufe del refrigerador o el interruptor
o panel de fusibles.
Para remover la puerta izquierda:
1.
Retire la cubierta de la bisagra superior, usando un
destornillador tipo Phillips remueva 5 tornillo.
2.
Retire el tornillo del cable de conexión a tierra de la
bisagra y tire de las dos conexiones del cable de
conexión a tierra hacia afuera de la bisagra.
Desconecte los tres arneses de cables y el tubo de
agua. Presione el primer anillo pequeño en el collar
de conexión para extraer el tubo2.
3.
Con un destornillador Phillips grande, gire la bisagra
superior hacia la izquierda para quitar la bisagra/
placa superior.
Precaución:
después de la bisagra se retira la puerta
puede caer hacia delante . Por favor asegurar la
puerta durante este proceso.
4.
Lift the door from the middle hinge pin and remove the
door. Place the door, inside facing up, on a nonscratch
surface.
Para remover la puerta derecha:
1.
Retire la cubierta de la bisagra superior, usando un
destornillador tipo Phillips remueva 5 tornillos.
2.
Con un destornillador Phillips grande, gire la bisagra
superior hacia la izquierda para quitar la bisagra/
placa superior.
Precaución:
después de la bisagra se retira la puerta
puede caer hacia delante. Por favor asegurar la puerta
durante este proceso.
3.
Levante la puerta de la bisagra del medioy retire la
puerta. Coloque la puerta, con el interior hacia
arriba, sobre una superficie que no arañe.
en-us
9
If the refrigerator doors are not
properly aligned:
WARNING
Risk of electric shock!
Before removing the top panel:
1. Shut off the water supply to the
appliance.
2. Unplug the appliance or switch
off the fuse.
1. Determine which refrigerator door
needs adjustment.
2. Remove the five screws on the top
panel.
3. Raise the panel.
4. Loosen the screw.
Do not remove the screw!
5. Move the hinge sideways to adjust
the refrigerator door.
6. Tighten the screw.
7. Realign panel.
8. Insert and tighten the five screws.
Adjusting the freezer
compartment drawer
1. Determine which side needs
adjustment.
2. Loosen the two screws.
Do not remove the screws!
3. Use the top screw to adjust the
freezer compartment drawer.
4. Tighten the two screws.
Installing the handles
Do not install the handles until the
appliance is installed in its designated
location and is level.
All handles are the same and are
installed in the same manner.
1. Remove the protective films from
the refrigerator doors and the
freezer compartment drawer.
2. Insert the door handles into the
guides.
Refrigerator doors: The handle
screws must face the center of
the appliance.
Freezer compartment drawer:
The handle screws must face
down.
3. Tighten the handle screws with the
accompanying Allen wrench.
Installing the base plate
1. Remove the three screws on the
appliance.
2. Mount the base plate.
3. Insert the three screws and
tighten.
en-us
9
If the refrigerator doors are not
properly aligned:
WARNING
Risk of electric shock!
Before removing the top panel:
1. Shut off the water supply to the
appliance.
2. Unplug the appliance or switch
off the fuse.
1. Determine which refrigerator door
needs adjustment.
2. Remove the five screws on the top
panel.
3. Raise the panel.
4. Loosen the screw.
Do not remove the screw!
5. Move the hinge sideways to adjust
the refrigerator door.
6. Tighten the screw.
7. Realign panel.
8. Insert and tighten the five screws.
Adjusting the freezer
compartment drawer
1. Determine which side needs
adjustment.
2. Loosen the two screws.
Do not remove the screws!
3. Use the top screw to adjust the
freezer compartment drawer.
4. Tighten the two screws.
Installing the handles
Do not install the handles until the
appliance is installed in its designated
location and is level.
All handles are the same and are
installed in the same manner.
1. Remove the protective films from
the refrigerator doors and the
freezer compartment drawer.
2. Insert the door handles into the
guides.
Refrigerator doors: The handle
screws must face the center of
the appliance.
Freezer compartment drawer:
The handle screws must face
down.
3. Tighten the handle screws with the
accompanying Allen wrench.
Installing the base plate
1. Remove the three screws on the
appliance.
2. Mount the base plate.
3. Insert the three screws and
tighten.
INSTALACION DEL REFRIGERATOR
empujar
F706-10a(스)(Kenmore)_25_5Cu_ft Renewal.indd 52 2020-03-31 오후 5:04:58