Installation Guide

ManualsBrandsKenmore ManualsAir Conditioners77060 6,000 BTU 115V Window Air Conditioner - White

READ BEFORE INSTALLING UNIT

MSII & MSIII Window Mounting (5~8K BTU)

Installation Instructions

Before installing, the top rail must be assembled on the unit.

Top Rail Hardware

Qty.

3/8Ǝ Screw

Top Rail

Some assembly is required. Please read these instructions

carefully.

To avoid risk of personal injury, property damage, or product damage due to the weight of this device and sharp

edges that may be exposed:

Air conditioners covered in this manual pose an excessive weight hazard. Two or more people are needed to

move and install the unit. To prevent injury or strain, use proper lifting and carrying techniques when moving unit.

Carefully inspect location where air conditioner will be installed. Be sure it will support the weight of the unit over

an extended period of time.

Handle air conditioner with care. Wear protective gloves whenever lifting or carrying the unit. AVOID the sharp

metal fins on front and rear coils.

Make sure air conditioner does not fall during installation.

DO NOT USE ANY SCREWS OTHER THAN

THOSE SPECIFIED HERE.

SAVE CARTON and these INSTALLATION

INSTRUCTIONS for future reference. The carton is

the best way to store unit during winter, or when not

in use.

FOR SAFETY REASONS, THE TOP RAIL MUST BE

SECURELY FASTENED WITH ALL FOUR (4)

SCREWS.

A. Remove the air conditioner from the carton and place on a flat surface.

B. Remove top rail from the rear of the packaging material as shown in Fig. A

C. Align the hole in the top rail with those on the top of the unit as shown in Fig. B

D. Secure the top rail to the unit with the 3/8Ǝ Screws as shown in Fig. C

Fig. B

Packaging

Fig. A

Fig. C

Top Rail

Drill (If pilot holes are needed)

Mounting Hardware

Qty.

( or Wooden windows)

weather stripping

insulation panel

ruler

(10”X3/4”X1/12”)

window sash seal foam 1

16120300A05202

Summary of content (5 pages)

PAGE 1
Installation Instructions READ BEFORE INSTALLING UNIT MSII & MSIII Window Mounting (5~8K BTU) To avoid risk of personal injury, property damage, or product damage due to the weight of this device and sharp edges that may be exposed: Air conditioners covered in this manual pose an excessive weight hazard. Two or more people are needed to move and install the unit. To prevent injury or strain, use proper lifting and carrying techniques when moving unit.
PAGE 2
How to Install Installation LEFT + RIGHT FILLER PANEL ASSEMBLY NOTE: Top Rail and Side Panels at each side are offset to provide the proper pitch to the rear of (5/16”). This is necessary for proper condensed water utilization and drainage. If you are not using the Side Panels for any reason, this pitch to the rear must be maintained! Place unit on floor, a bench or a table. There is a Left and Right side Filler Panels - be sure to use the proper panel for each side.
PAGE 3
How to Install Installation Keep a firm grip on the air conditioner, carefully place the unit into the window opening so the bottom of the air conditioner frame is against the window sill (FIG. 6A & FIG. 6B). Carefully close the window behind the top rail of the unit. FIG. 6B FIG. 6A INSIDE OUTSIDE INSIDE OUTSIDE Wooden Windows Vinyl-Clad Windows Extend the side panels out against the window frame (FIG. 7A for wooden windows), (FIG. 7B for Vinyl-Clad windows). FIG. 7A FIG.
PAGE 4
Installation Measure the width of the inner side curtain with the provided ruler, as shown (FIG. 10). Mark a line on the patterned side of the provided insulation panel according to the measured width, then cut out the insulation panel along the line, as shown (FIG.11). Place the patterned side of the insulation panel to face inside your room, then slide the insulation panel into the frame until the panel goes into the side curtain frame completely.
PAGE 5
Installation 10 FIG. 15A & FIG. 15B). normal use, correct the slope otherwise. FIG. 15B FIG. 15A H H INSIDE OUTSIDE H about Bottom Rail INSIDE OUTSIDE Bottom Rail H1 Wooden Window Vinyl-Clad Window FIG. 16 11 In order to minimize air leaks between the room air conditioner and the window opening, suitable weather stripping(trim the provided weather stripping into suitable size) should be applied in case of any gaps found at the location as indicated by the arrows in Fig. 16.