Installation Instructions Questions? Call 1-800-4-MY-HOME® BEFORE YOU Over the Range Microwave Oven or Visit our Website at: http://www.kenmore.com BEGIN Read these instructions completely and carefully. « Note to Consumer — Keep these instructions for future reference. ° IMPORTANT — Save these instructions for local inspector's use. * Skill level — Installation of this appliance requires basic mechanical and electrical skills.
Installation Instructions CONTENTS Adapting Microwave Blower for Outside Back Exhaust... General Mount the Microwave Oven .........0008 19 information Important Safety Instructions ......0000eee 3 Electrical Requirements Damage - Shipment/Installation...........000.. Parts Included.......... Recirculating oo... ................ eee eee eee eeeeeeeteceeeee 3 eee eee eeeeeteeeeeeeeees 20 -22 Attach Mounting Plate to Wall... 20 4 Preparation of Top Cabinet ......
Installation Instructions IMPORTANT SAFETY INSTRUCTIONS This product requires a three-prong grounded outlet. The installer must perform a ground continuity check on the power outlet box before beginning the installation to ensure that the outlet box is properly grounded. If not properly grounded, or if the outlet box does not meet electrical requirements noted (under ELECTRICAL REQUIREMENTS), a qualified electrician should be employed to correct any deficiencies.
Installation Instructions PARTS INCLUDED conr) DAMAGE—SHIPMENT/ INSTALLATION ADDITIONAL * If the unit is damaged in shipment, return the unit to the store in which it was bought for repair or replacement. PART QUANTITY S| * If the unit is damaged by the customer, repair or replacement is the responsibility of the customer. ° If the unit is damaged by the installer (if other than the customer), repair or replacement must be made by arrangement between customer and installer.
Installation Instructions TOOLS YOU WILL NEED O} HE) Pencil #1 Phillips screwdriver Ruler or tape measure and straight edge Fae, Carpenter square (optional) Tin snips (for cutting damper, if required) Scissors (to cut template, if necessary) P ¥ Electric drill with %e6", 2" and %" drill bits Ge 6 Saw (saber, hole or keyhole) Stud finder —a—— =) level Safety goggles MOUNTING Filler blocks or scrap wood pieces, if needed for top cabinet spacing (used on recessed bottom cabinet installations
Installation 1 | PLACEMENT A.| Instructions OF THE MOUNTING PLATE Cut the middle of the outer protective plastic bag to remove the mounting plate REMOVING THE MICROWAVE OVEN FROM THE CARTON/ REMOVING THE MOUNTING PLATE Screws Y Mounting Plate Screws 1] Remove the installation instructions,use and care, exhaust adapter, turntable ring, shelf, filters, glass tray and the small hardware bag. Do not remove the Styrofoam protecting the front of the oven.
Installation C.| DETERMINING WALL Instructions PLATE LOCATION Plate position-beneath flat bottom cabinet eI C Draw matching the centerline and touching the bottom of the cabinet. _ ate b position-beneath h CABINET Plate position-beneath framed recessed cabinet bottom Draw a vertical line on | the wall at the center of the 30” wide space. Tape the Rear Wall wall Template onto the PI UNDER YOUR 30” to Cooktop real [iline on the wall at the center of the a vertical pace.
Installation Instructions ALIGNING THE WALL PLATE |! A, REAR WALLITEMPLATE "Centerline Hole B notches - [e009 e897 0000000 0 7090709 0 Horizontal Line at 0000 O09 8 8 8 6 OO a 00 of 0702020290" 0°07 3 Area E CAUTION: Wear gloves to avoid cutting fingers on sharp edges. 5, x ! Opa g? | \ Horizontal Line Draw a horizontal line on wall at the bottom of “Rear Wall Template’. NOTE: Holes A and B are inside area E.
Installation 2 | INSTALLATION TYPES Instructions (Choose A, B or C) This microwave oven is designed for adaptation to the following three types of ventilation: NOTE: This microwave is shipped assembled for Recirculating. Select the type of ventilation required A. Outside Top Exhaust (Vertical Duct) for your installation and proceed to that section. B. Outside Back Exhaust (Horizontal Duct) C.
Installation Instructions INSTRUCTIONS FOR EXTERNAL EXHAUST DUCTING INSTALLATION NOTE: If you need to install ducts, note that the total duct length of Sia" x 10 Maximum (8.2 x 25.4 cm) rectangular or duct length: For satisfactory air movement, the total duct length of 5" (12.7 cm)diameter/ 6” (15.2 cm) diameter round duct should not exceed 120 equivalent feet (36.5 m). Outside ventilation requires an EXTERNAL EXHAUST DUCT.Read the following carefully. 3%4" x 10” (8.2 x 25.
Installation EXTERNAL EXHAUST OUTSIDE TOP EXHAUST Instructions DUCTING (EXAMPLE ONLY) The following chart describes an example of one possible ductwork installation. SQ EQUIVALENT NUMBER EQUIVALENT X (1) 24 Ft. (7.3 m) 12 Ft. (3.6 m) Straight Duct | 12 Ft. (3.6 m) (6"/15.2 cm Round) X (1) 12 Ft. (3.6 m) Rectangular-to-Round X (1) 5 Ft. (1.5 m) DUCT PIECES WES. Roof Cap LENGTH x 24 Ft. (7.3 m) 5 Ft. (1.
Installation Instructions OUTSIDE TOP EXHAUST A INSTALLATION (vertical Duct) OVERVIEW A1. Attach Mounting Plate to Wall A2. Prepare Top Cabinet A3. Adapting Microwave Blower for Outside Top Exhaust Ad. Check Damper Operation AS. Mount Microwave Oven A6. Adjust Exhaust Adaptor A7. Connect Ductwork IMPORTANT NOTES: * Make sure the screws for the blower motor and blower plate are securely tightened when they are reinstalled. This will help to prevent excessive vibration.
Installation A2.| Instructions USE TOP CABINET TEMPLATE FOR PREPARATION OF TOP CABINET [2] Carefully pull out the blower unit. The wires will extend far enough to allow you to adjust the blower unit. End B You need to drill holes for the top support screws, a hole large enough for the power cord to fit through, and a cutout large enough for the exhaust adaptor. End A Back of Microwave Roll the blower unit 90° so that fan blade openings are facing out the top of the microwave.
Installation A3 Instructions MOUNT OVEN ADAPTING MICROWAVE BLOWER FOR OUTSIDE TOP EXHAUST THE MICROWAVE [5] Secure blower unit to microwave with the screw removed in Step 1. Make sure the screw is tight. 6 | Replace blower plate with the screw removed in Step 1. Make sure the screw is tight. FOR EASIER INSTALLATION AND PERSONAL SAFETY, WE RECOMMEND THAT TWO PEOPLE INSTALL THIS MICROWAVE OVEN. IMPORTANT: Do not grip or use handle during installation.
Installation A5.|] Instructions MOUNT THE MICROWAVE OVEN A6.| (cont.) Open the top cabinet and adjust the exhaust adaptor to connect to the house duct. Cabinet Front Cabinet Bottom Shelf wa ADJUST THE EXHAUST ADAPTOR Filler Block Blower Plate AN Y a Ee ~My, - a2 Equivalent to Depth of Cabinet EAA Recess a _ atl Lb Back of Microwave Damper a -~<«— Self-Aligning Screw Microwave Oven Top oe A7.
Installation B | OUTSIDE INSTALLATION BACK EXHAUST (Horizontal Duct) OVERVIEW Prepare Rear Wall Remove Blower Plate Attach Mounting Plate to Wall Prepare Top Cabinet Adjust Blower Mount the Microwave Oven eowenscenagewensceeetenpenenenetenceneesnetencens fi i ‘ B1. B2. B3. B4. B5. B6. Instructions IMPORTANT NOTES: * Make sure the screws for the blower motor and blower plate are securely tightened when they are reinstalled. This will help to prevent excessive ¢.. vibration.
Installation B3. Instructions ATTACH THE MOUNTING PLATE TO THE WALL B4.| USE TOP CABINET TEMPLATE FOR PREPARATION OF TOP CABINET You need to drill holes for the top support screws and a hole large enough for the power cord to fit through. Attach the plate to the wall using toggle bolts. At least one wood screw must be used to attach the plate to a wall stud. 1 | Remove the toggle wings from the bolts. ® Read the instructions on the TOP CABINET TEMPLATE.
Installation B5.| 3 | Instructions Place the blower unit back into the opening. ADAPTING MICROWAVE BLOWER FOR OUTSIDE BACK EXHAUST (cont.) AFTER: Fan Blade Openings Facing Back Roll the blower unit 90° Before Rotation After Rotation CAUTION: Do not pull or stretch the blower unit wiring. Make sure the wires are not pinched, and that they are properly secured.
Installation B6.; Instructions Cabinet Front MOUNT THE MICROWAVE OVEN J Cabinet Bottom Shelf meet / va | Equivalent DG | SN FOR EASIER INSTALLATION AND PERSONAL SAFETY, WE RECOMMEND THAT TWO PEOPLE INSTALL THIS MICROWAVE OVEN. \ Filler Block to Depth of Cabinet Recess 1 Self-Aligning Screw Microwave Oven Top 4 | Attach the microwave oven to the top cabinet. IMPORTANT: Do not grip or use handle during installation. [5 | Insert 2 self-aligning screws through outer top cabinet holes.
Installation C RECIRCULATING INSTALLATION C1. C2. C3. C4. C5. Instructions (Non-Vented Ductless) OVERVIEW Attach Mounting Plate to Wall Prepare Top Cabinet Check Blower Plate Mount the Microwave Oven Install or change Charcoal Filter IMPORTANT NOTES: * Make sure the screws for the blower motor and blower plate are securely tightened when they are reinstalled. This will help to prevent excessive vibration.
Installation C2 Instructions C4.| USE TOP CABINET TEMPLATE FOR PREPARATION OF TOP CABINET MOUNT THE MICROWAVE OVEN You need to drill holes for the top support screws and a hole large enough for the power cord to fit through. FOR EASIER INSTALLATION AND PERSONAL SAFETY, WE RECOMMEND THAT TWO PEOPLE INSTALL THIS MICROWAVE OVEN. IMPORTANT: Do not grip or use handle during installation. NOTE: If your cabinet is metal, use the nylon grommet around the power cord hole to prevent cutting of the cord.
Installation C4.| Instructions MOUNT THE MICROWAVE OVEN (cont.) [2 | Open the microwave door and remove the two vent mounting screws located on top of the microwave using a #1 Phillips screwdriver. | 5 |Insert 2 selfaligning screws through outer top cabinet holes. Turn two full turns on each screw. |3 | Slide the vent left and tip forward. Lift out to remove. 4] | 6 | Tighten center screw completely. Lift the bottom of the charcoal filter. Slide the filter straight out.
Installation Instructions BEFORE 1 YOU USE YOUR MICROWAVE Make sure the microwave oven has been installed according to instructions. 5 Replace house fuse or turn breaker back on. - lel 6 2 Remove all packing material from the microwave oven. 3 Install turntable ring and glass tray in cavity. Read the USE 7 "i 4 —4 & CARE Manual. KEEP INSTALLATION INSTRUCTIONS FOR THE LOCAL INSPECTOR'’S USE. Plug power cord into a dedicated 15- to 20-amp electrical outlet. 8, | FILL OUT PRODUCT AN SEND IN.
NOTE: IT 1S, VERY IMPORTANT TO. READ AND FOLLOW THE DIRECTIONS IN THE INSTALLATION INSTRUCTIONS, BEFORE PROCEEDING WITH THIS REAR WALL TEMPLATE. ‘This Rear Wafl Template serves ta position the bottam mounting plate and fo locate the horizontal exhaust outlet.
Instrucciones de Horno microondas (encima de la estufa) instalacion éPreguntas? Llame al 1-800-4-MY-HOME® © Visitenos en Internet en: hitp://www.kenmore.com ANTES DE EMPEZAR Lea estas instrucciones completamente ° IMPORTANTE: y con atencién. conserve estas instrucciones para uso futuro del inspector local. ° IMPORTANTE: ¢ Nota para el consumidor: conserve estas instrucciones para referencia futura. * ¢ Nota para el instalador: asegurese de dejar estas instrucciones en manos del consumidor.
Instrucciones de instalacion CONTENIDO Ajuste del ventilador del microondas para la extracciOn superior Externd -e-rseceeseeceeeeees 17-18 Informacion general Instalacién del horno microondas Instrucciones importantes sobre seQguriddd Requisitos SIE CHICOS Dafios-envio we cssssssseeseesees 3 RECIPCUICCION ....ecsescssesssssessesecesessescessesseceeseessceeesnessees 20-22 ..
Instrucciones de instalacion INSTRUCCIONES IMPORTANTES SOBRE SEGURIDAD Este product require un tomacorriente de tres clavijas con puesta a tierra. Antes de proceder con la instalacién del electrodoméstico, el instalador debe realizar una verificacién de la continuidad de la puesta a tierra del tomacorriente, a fin de asegurarse de que es correcta.
Instrucciones de instalacion DANOS-ENVIO (TRANSP -ORTE)/INSTALACION ® Si el producto PIEZAS INCLUIDAS «ont KIT DE FERRETERIA ha resultado dafiado durante su envio (transporte), devuélvalo a la tienda/el almacén adquiriéd, para que lo reparen o lo cambien donde PIEZA to CANTIDAD por uno nuevo. Plantilla para e Si el producto ha sido dafiado por el comprador, la reparacién o el reemplazo el gabinete del producto es responsabilidad superior del comprador.
Instrucciones de instalacion HERRAMIENTAS NECESARIAS —HE) Regla o cinta métrica Destornillador Phillips #1 con borde recto Lapiz .
Instrucciones de instalacion > COLOCACION DE LA PLACA DE INSTALACION 1 | Come la bolsa de pldstico en el medio para retirar la placa de instalacién. . Tornillos Tornillos PROCEDIMIENTO PARA SACAR DE LA CAJA EL MICROONDAS Y LA PLACA DE INSTALACION Placa de instalacién Retirar las instrucciones de instalacién, uso y cuidado, adaptador bandeja de escape, anillo giratorio, estante, filtros, de vidrio y bolsa de accesorios pequefia. No retire el poliestireno de la parte delantera del horno.
oO Instrucciones de instalacion UBICACION DE LA PLACA PARA LA PARED DE BAJO DEL GABINETE Posicién de la placa-debajo de la superficie plana inferior del gabinete Posicién de la place-debajo de la superficie hueca inferior (con marco) del gabinete é Dibuja una linea vertical en la oe pared 30" a la superficie de coccién ' en el centro del espacio cuyo ancho es 30". Cinta Dibuja una linea vertical en la pared la Plantilla de pared en el centro del espacio cuyo ancho es 30".
Instrucciones de instalacion D.| \ ALINEACION DE LA PLACA PARA LA PARED REAR Agujero B Vso I: WALLITEMPLATE Muescas de la linea de centro 29,099,9,! p 25% 6%o' no c 070700 Area E PRECAUCION: para png? AguieroA 5, evitar cortes por los bordes afilados. * i| Trace una La linea horizontal linea horizontal en la pared desde el fondo de "Plantilla de pared posterior". NOTA: Los Agujero A y los Agujero B se encuentran dentro de la regin E.
Instrucciones de instalacion 2 TIPOS DE INSTALACION Este horno microondas esta disefiado para adaptarse a los tres tipos siguientes de ventilacién: A. Extraccién superior externa (conducto vertical) B. Extraccién trasera externa (conducto horizontal} C. Recirculacién (sin conducto de extraccién) A | (A Eleccién Entre A, B o C) NOTA: este horno microondas se ha fdabricado para un sistema de Recirculacién.
Instrucciones de instalacion INSTRUCCIONES NOTA: DE INSTALACION DE CONDUCTOS en caso de que sea necesario instalar conductos, tenga en cuenta Largo maximo DE ESCAPE EXTERNAS del conducto: que el largo total de los conductos. rectangulares (ancho de 3 1/4" X 10" u 8,2 cm X 25,4 cm) 0 redondos (didmetro de 5" 6 12,7 cm) /(didmetro de 6" 6 15,2 cm) NO debe ser superior a 120 pies (36,5 m).
Instrucciones de instalacion CONDUCTOS DE ESCAPE EXTERNAS EXTRACCION SUPERIOR EXTERNA (SOLO EJEMPLO) La siguiente tabla contiene un ejemplo de uno posible instalacién de un sistema de conducto de extraccién.
Instrucciones de instalacion A EXTRACCION SUPERIOR EXTERNA (conducto vertica) DESCRIPCION GENERAL DE LA INSTALACION Al. Montaje de la placa de instalacién en la pared. A2. Preparacién del gabinete superior. A3. Ajuste del ventilador del microondas para la extraccién superior externa. AA. Verificacién del funcionamiento del regulador de extraccién. AS. Instalacién del horno microondas. Aé. Ajuste del adaptador de extraccidn. ° ° A7. Acoplamiento del sistema de conductos.
Instrucciones de instalacion A2. USO DE LA PLANTILLA PARA EL GABINETE SUPERIOR A FIN DE PREPARAR EL AREA DE DICHO GABINETE 2 Tire del ventilador con cuidado hacia afuera. Los cables se extenderdn lo suficiente para permitir el ajuste del ventilador. Seen ae.
Instrucciones de instalacion A3.| [5 A5.| AJUSTE DEL VENTILADOR DEL MICROONDAS PARA LA EXTRACCION SUPERIOR EXTERNA INSTALACION DEL HORNO MICROONDAS Fije el ventilador al microondas con el tornillo previamente retirado en el paso |. Asegurese de apretar el tornillo. | 6 | Vuelva a fijar la placa del ventilador con el tornillo previamente retiracdo en el paso 1. Asegurese de apretar el tornillo.
Instrucciones de instalacion A5.| INSTALACION DEL HORNO MICROONDAS Parte delantera A6.| AJUSTE DEL ADAPTADOR DE EXTRACCION (cont.
Instrucciones de instalacion B EXTRACCION TRASERA EXTERNA (Conducto Horizontal) DESCRIPCION GENERAL DE LA INSTALACION B1. Preparacién de la pared trasera B2. Desinstalacién del placa del ventilador B3. Montaje de la placa de instalacién en la pared B4. Preparacién del gabinete superior B5. Ajuste del ventilador B6.
Instrucciones de instalacion B3. | MONTAJE DE INSTALACION PLACA DE EN LA PARED [ B4. |USO DE LA PLANTILLA PARA EL GABINETE SUPERIOR A FIN DE PREPARAR EL AREA DE DICHO GABINETE LA Es necesario taladrar agujeros para los tomillos de soporte superior, asi como un agujero lo suficientemente, grande eléctrico pueda para que el cable pasar a través. Fije la placa en la pared con los tornillos de fiador. Al menos un tornillo para madera debe ser utilizado para fijar la placa a una viga de la pared.
Instrucciones de instalacion B5. | AJUSTE DEL VENTILADOR DEL MICROONDAS PARA LA EXTRACCION TRASERA EXTERNA (cont.) Vuelva a colocar el ventilador dentro de su abertura. DESPUES: Aberturas de las aletas del ventilador orlenladas hacia atras, Gire el ventilador 90°.
Instrucciones de instalacion INSTALACION DEL HORNO MICROONDAS Parte delantera A) i Bloque de relleno Equivalente a la profundidad le Sy N POR RAZONES DE SEGURIDAD PERSONAL Y PARA FACILITAR LA INSTALACION, SE RECOMIENDA QUE DOS PERSONAS INSTALEN EL HORNO MICROONDAS. IMPORTANTE: del gabinete Estante inferior del gabinete TOT Bé. de la superficie : | hueca cel gabinete &—— Tornillo autoalineante Parte superior del horno microondas [4 | Fije el horno microondas al gabinete superior.
Instrucciones de instalacion C RECIRCU LACION (Sin Conducto De Extraccién) DESCRIPCION GENERAL DE LA INSTALACION C1. Montaje de la placa de instalacién en la pared C2. Preparacién del gabinete superior C3. Verificacién del conjunto del Placa del Ventilador C4. Instalacién del horno microondas C5. Instalacién o cambiar del filtro de carbén NOTAS IMPORTANTES: @ Asegutrese de que los tornillos del motor del ventilador y la placa del ventilador queden instalarlos.
Instrucciones de instalacion [ea] C2. | USO DE LA PLANTILLA PARA EL GABINETE SUPERIOR A FIN DE PREPARAR EL AREA DE DICHO GABINETE Es necesario taladrar agujeros para los tornillos de soporte superior, asi como un agujero lo suficientemente grande el cable eléctrico pueda INSTALACION DEL HORNO MICROONDAS para que ’ pasar a través. POR RAZONES DE SEGURIDAD PERSONAL Y PARA FACILITAR LA INSTALACION, SE RECOMIENDA QUE DOS PERSONAS INSTALEN EL HORNO MICROONDAS.
Instrucciones de instalacion C4. INSTALACION DEL MICROONDAS HORNO 2 | (cont.) Abra la puerta del microondas y saque del horno con 5| los dos tornillos de montaje de ventilacién ubicados en la parte superior un destornillador Phillips #1. Inserte 2 tornillos autoalineantes a través de los agujeros exteriores del gabinete superior. Apriete cada uno de, los tornillos dos vueltas completas. Deslice el ducto de ventilacién hacia la izquierda e incline hacia adelante. Levantelo para sacarlo. .
Instrucciones de instalacion ANTES DE USAR EL HORNO Asegutrese de que el horno microondas haya sido instalado 5. segun las instrucciones. Vuelva a colocar el fusible correspondiente o encienda nuevo el disyuntor. Lea el manual de use y cuidado. Retire todo el material de empaque del horno microondas. Instale el anillo y el plato giratorio en el interior del horno. CONSERVE LAS INSTRUCCIONES DE INSTALACION PARA USO DEL INSPECTOR LOCAL.
NOTA: ES MUY IMPORTANTE LEER ¥ SEGUIR LAS Corte la plantilla ubicada en la pared de atras a través de la linea depunts fl DIRECCIONES EN LAS INSTRUCCIONES DE INSTALACION | ANTES DE PROCEDER CON ESTA PLANTILLA DE PARED POSTERIOR, Site plentile Oe fe pared pastriaysrve pare colscar el plato de montefe inferior y pore colater le solide da excape hariventl un alvel pore cersiorane de que to plontllsesté colocoes de 2.