Specifications

11
Installation Instructions
STEP 14STEP 14
STEP 14STEP 14
STEP 14
PRE-TEST CHECKLISTPRE-TEST CHECKLIST
PRE-TEST CHECKLISTPRE-TEST CHECKLIST
PRE-TEST CHECKLIST
Review this list after installing your dishwasherReview this list after installing your dishwasher
Review this list after installing your dishwasherReview this list after installing your dishwasher
Review this list after installing your dishwasher
to avoid charges for a service call that is notto avoid charges for a service call that is not
to avoid charges for a service call that is notto avoid charges for a service call that is not
to avoid charges for a service call that is not
coco
coco
co
vered by yvered by y
vered by yvered by y
vered by y
our warrantyour warranty
our warrantyour warranty
our warranty
..
..
.
¨ Check to be sure power is OFF.
¨ Open door and remove all foam and paper packaging.
¨ Locate the Owner’s Manual in the literature package.
¨ Read the Owner’s Manual for operating instructions.
¨ Check door opening and closing. If door does not open and
close freely or tends to fall, check spring adjustments. See
Step 1.
¨ Check to be sure that wiring is secure under the
dishwasher, not pinched or in contact with door springs or
other components. See Step 9.
¨ Check door alignment with tub. If door hits tub, level
dishwasher. See Step 10.
¨ Pull lower rack out, about half way. Check to be sure it
does not roll back or forward on the door. If the rack
moves, adjust leveling legs. See Step 10.
¨ Check door alignment with cabinet. If door hits cabinet,
reposition or relevel dishwasher. See Step 10.
¨ Verify water supply and drain lines are not kinked or in
contact with other components. Contact with motor or
dishwasher frame could cause noise. See Step 8.
¨ Turn on the sink hot water faucet and verify water
temperature. Incoming water temperature must be
between 120°F and 150°F. A minimum of 120°F temperature
is required for best wash performance. See "Prepare Hot
Water Line", page 5.
¨ Add 2 quarts of water to the bottom of the dishwasher to
lubricate the pump seal.
¨ Turn on water supply. Check for leaks. Tighten connections
if needed.
¨ Remove protective film if present from the control panel
and door.
STEP 13STEP 13
STEP 13STEP 13
STEP 13
CC
CC
C
ONNECT POONNECT PO
ONNECT POONNECT PO
ONNECT PO
WERWER
WERWER
WER
SUPPLSUPPL
SUPPLSUPPL
SUPPL
YY
YY
Y
Skip this step if equipped with power cord.Skip this step if equipped with power cord.
Skip this step if equipped with power cord.Skip this step if equipped with power cord.
Skip this step if equipped with power cord.
Verify that power is turned off at the source.Verify that power is turned off at the source.
Verify that power is turned off at the source.Verify that power is turned off at the source.
Verify that power is turned off at the source.
• Remove junction box cover “A”.
• Locate the three dishwasher wires, (white, black and green)
with stripped ends. Insert dishwasher wires through the small
hole in the junction box “B”.
• Secure house wiring to the bottom of the junction box with
a strain relief “C”.
• User wire nuts to connect incoming ground to green, white
to white and black to black “D”.
• Replace junction box cover “E”. Check to be sure that wires
are not pinched under the cover.
WW
WW
W
ARNINGARNING
ARNINGARNING
ARNING
If house wiring is not 2-wire with ground,
a ground must be provided by the
installer. When house wiring is aluminum,
be sure to use UL Listed anti-oxidant
compound and aluminum-to-copper
connectors.