Use & Care / Installation Manual Manual de Uso y Cuidado / Instalación English / Español Models/Modelos 233.5992*, 5993* Kenmore Range Hood ® Campana de cocina * = color number, número de color P/N 99528329E Sears Brands Management Corporation, Hoffman Estates, IL 60179 USA www.kenmore.com www.sears.
READ AND SAVE THESE INSTRUCTIONS TABLE OF CONTENTS SECTION........................................................................ PAGE Safety Instructions ................................................................2 Warranty ...............................................................................3 Operation ..............................................................................3 Cleaning ................................................................................
OPERATION KENMORE LIMITED WARRANTY CONTROLS OFF Safety LO MED HI This hood is operated using (5) pushbuttons on the front of the hood canopy. The fan OFF pushbutton turns the fan off. The fan low, medium and high speed pushbuttons turn the fan on to three different speed settings. Warranty The light pushbutton turns the lights on and off. LIGHT BULBS Cleaning CAUTION ! Bulbs may be hot. Always allow bulbs to cool down before removing them.
PARTS INCLUDED WITH HOOD CLEANING Proper maintenance of the Range Hood will assure proper performance of the unit. 8 MOUNTING SCREWS (#8 x 3/8” Pan Head) MOTOR The motor is permanently lubricated and never needs oiling. If the motor bearings make excessive or unusual noise, replace the motor with the exact service motor. The impeller should also be replaced. 2 WASHERS GREASE FILTER The grease filter should be cleaned frequently. Use a warm dishwashing detergent solution.
EQUIVALENT DUCT LENGTH CHART Broan Model 419 6-in. Round Elbow Equivalent length 8 ft. Broan Model 430 3¼-in. x 10-in. Right-angle Short Eave Elbow Equivalent length 15 ft. Broan Model 431 3¼-in. x 10-in. Right-angle Long Eave Elbow Equivalent length 15 ft. Kenmore Model 59091 Roof Cap (accepts 7-in. round or 3¼-in. x 10-in. duct) Equivalent length 30 ft. (7-ft.
INSTALL THE DUCTWORK WARNING To reduce the risk of fire, use only metal ductwork. 1. Decide where the ductwork will run between the hood and the outside. 2. A straight, short duct run will allow the hood to perform most efficiently. 3. Long duct runs, elbows and transitions will reduce the performance of the hood. Use as few of them as possible. Larger ducting may be required for best performance with longer duct runs. 4. Install a wall cap or roof cap.
INSTALL UPPER FLUE MOUNTING BRACKET Center of installation CL Recommended distance between screw holes Ceiling 11⁄ 8 ” 5¾” Ø 5/16” TYP. 27⁄ 8 ” Flush with the ceiling Center of installation Warranty Ceiling Safety 1. If a framing member is not present, drill two 5⁄16” diameter holes where shown. Insert drywall anchors into the holes. 2. Center the bracket over the hood location and flush with the ceiling. Make sure that the slots of the upper flue bracket are at the bottom.
INSTALL CURVED GLASS PLATE 1. Place range hood body on its back, with controls facing up. Place cardboard under hood to protect countertop or table finish. 2. Position the curved plate glass over the range hood body as shown. 3. Install rubber bushings into all (4) holes of the glass. 4. Place a plastic decorative washer onto (4) M4 x 1-in. flathead mounting screw. 5. Align holes in glass with holes in the range hood body.
INSTALL THE HOOD (HORIZONTALLY DUCTED HOODS ONLY) LOWER FLUE MOUNTING BRACKET 8¼” MAX. SIDE VIEW HOLE LOCATIONS Ø5/16” TYP. Service Parts 9 Installation 4. If a framing member is not present: With the hood hanging in place, drill through both holes located in the inside lower back of hood using a 5/16” drill bit. Insert the included drywall anchors into the drilled holes (one for each hole). 5.
INSTALL THE HOOD (VERTICALLY DUCTED HOODS ONLY) 1. DO NOT REMOVE the protective plastic film covering the decorative flues at this time. 2. Align the hood and center it above the hood mounting bracket. Gently lower the hood until it securely engages the bracket. LOWER FLUE MOUNTING BRACKET LOWER FLUE INSIDE BACK OF HOOD 7. Remove the upper flue from inside the lower flue. Install the lower flue bracket to the lower flue using (2) flue bracket screws (#8 x 3/8”).
INSTALL THE HOOD (NON-DUCTED HOODS ONLY) 4-7/8” NON-DUCT COLLAR 6” ALUMINUM FLEX DUCT A UPPER FLUE MOUNTING BRACKET - FRONT VIEW UPPER FLUE Cleaning NON-DUCT FILTER MOUNTING TABS NON-DUCT RECIRCULATION FILTER METAL LATCH Installation GREASE FILTER 17. Install the non-duct recirculation filter as shown. Turn mounting tabs on hood to secure filter. 18. Reinstall grease filter by aligning rear filter tabs with slots in the hood. Push in the metal latch tab, push filter into position and release.
INSTALL FLUE EXTENSION FOR 9-FT. CEILINGS Note: 9-ft. ceilings require the purchase of a flue extension, Kenmore part number 59920. 1. Discard the upper flue (supplied with the hood) and replace it with the longer flue section. 2. Follow all steps shown in the section “INSTALL THE HOOD” for horizontal, vertical and non-ducted installations. SERVICE PARTS Models 233.5992*, 5993* * = color number KEY 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 9 12 PART NO. DESCRIPTION QTY.