Installation Guide

3
INSTALLATION REQUIREMENTS
Tools and Parts
Gather the required tools and parts before starting installation.
All installations
In addition, for new installations
Parts supplied
A. 2 – drain hose clamps, 1 large and 1 small
B. 2 – #10 x ¹⁄₂" Phillips-head screws
C. Drain hose
D. On some Kenmore Elite models, carton containing handle, hex
key and 3 setscrews.
E. On Kenmore PRO
TM
models, assembly containing handle, 2⁵⁄₈"
mounting screws, 2 backing plates and handle installation
instruction sheet.
F. 2 – undercounter mounting brackets (top)
G. 2 – custom tape
Make sure all these parts are included. If they are not included, call
1-800-4-MY-HOME.
See separate parts list for accessories available for your
dishwasher.
Supplied in Kit:
■ 4 Plastic studs (attached to each other by runners)
■ 4 Short screws (10-16 hex head screw)
■ 4 Long screws (8-18 Torx
®†
head screws)
■ 1 Template (located inside Use and Care Guide bag assembly)
■ 1 Instruction Sheet (located inside Use and Care Guide bag
assembly)
NOTE: The screws supplied are used for only ³⁄₄" thick wooden
panel. If the wooden panel is less than ³⁄₄" thick, customer must
purchase screws locally.
Location Requirements
Do not run drain lines, water lines or electrical wiring where they
can interfere with or contact dishwasher motor or legs.
The location where the dishwasher will be installed must provide
clearance between motor and flooring. Motor should not touch the
floor.
Do not install dishwasher over carpeted flooring.
Shelter dishwasher and water lines leading to dishwasher against
freezing. Damage from freezing is not covered by the warranty.
A side panel kit is available from your dealer for installing your
dishwasher at the end of your cabinetry.
A moisture barrier accessory (Part Number 4396277) is available
from your dealer for installing underneath the countertop. This may
also be obtained by calling 1-800-4-MY-HOME.
Check location where dishwasher will be installed. The location
must provide:
■ easy access to water, electricity and drain.
■ convenient access for loading and unloading dishes. Corner
locations require a 2" (5.1 cm) minimum clearance between the
side of the dishwasher door and the wall or cabinet.
■ square opening for proper operation and appearance.
■ cabinet front perpendicular to floor.
■ level floor. (If floor at front of opening is not level with floor at
rear of opening, shims may be needed to level dishwasher.)
NOTE: To avoid shifting during dishwasher operation, shims must
be securely attached to the floor.
If dishwasher will be left unused for a period of time or in a
location where it may be subject to freezing, have it winterized by
authorized service personnel.
Make sure pipes, wires and drain hose are within the shaded area
shown in the “Cutout dimensions” section.
Helpful Tip: If the floor in the dishwasher opening is uneven
(example: tile flooring only partway into opening), you will
need to be exact in measuring dimensions and in leveling
dishwasher.
†®TORX is a registered trademark of Saturn Fasteners, Inc.
Tools needed:
■ Pliers
■ Phillips screwdriver
■ ⁵⁄₁₆" and ¹⁄₄" nut drivers or
hex sockets
■ Measuring tape or ruler
■ 10" adjustable wrench that
opens to 1¹⁄₈" (2.9 cm)
■ Flat-blade screwdriver
■ Utility knife
■ 2 twist-on wire connectors
which are the proper size to
connect your household
wiring to 16-gauge wiring
in dishwasher
■ Small level
■ Flashlight
■ Shallow pan
■ ⁵⁄₈" open-end wrench
■ Bath towel
■ Wood block
Parts Needed:
■ ³⁄₈" Compr x ³⁄₄" hose
fitting. Contact your local
Sears Store to purchase Kit
Number 11000.
Tools needed: Parts needed:
■ Cordless drill with ¹⁄₂", ³⁄₄",
and 1¹⁄₂" hole saw bits
■ Small tubing cutter
■ Wire stripper
■ 1¹⁄₂" to 2" screw-type clamp
if connecting to waste tee
■ Copper tubing (³⁄₈"
recommended) or flexible
stainless steel braided fill
line
■ Clamp connector or
conduit connector to fit a
⁷⁄₈" (2.2 cm) diameter hole
A
B
C
F
D
E
G