m .u a co CD-RECEIVER INSTRUCTION MANUAL AMPLI-TUNER LECTEUR DE CD MODE D’EMPLOI РAДИОПРИЕMНИК С KOMПAKT–ДИСKAMИ ИHCTPУKЦИЯ ПO ЭKCПЛУATAЦИИ АВТОМАГНІТОЛА ІНСТРУКЦІЯ З ЕКСПЛУАТАЦІЇ 13 0. KDC-3051R KDC-3051G KDC-3051RY KDC-3051GY KDC-315A KDC-315R KDC-3251RY This symbol mark indicates that Kenwood manufactured this product so as to decrease harmful influence on the environment. Изделие изготовлено в Mалайзии Autogood products Internet store “130”© 2010 Kenwood Corporation All Rights Reserved.
Safety Safety 2 Preparation 4 How to attach/detach the faceplate How to reset your unit Initial settings before operations Basic operations 5 Getting started 6 Canceling the display demonstration Setting the demonstration mode Adjusting the clock Listening to the radio 6 Adjust [SETTINGS] mode settings 8 13 0.
ENGLISH The marking of products using lasers Declaration of Conformity with regard to the EMC Directive 2004/108/EC EU Representative’s: Kenwood Electronics Europe BV Amsterdamseweg 37, 1422 AC UITHOORN, The Netherlands This Product is not installed by the manufacturer of a vehicle on the production line, nor by the professional importer of a vehicle into an EU Member State.
Preparation 1 2 1 2 Do not expose the faceplate to direct sunlight, excessive heat, or humidity. Also avoid places with too much dust or the possibility of water splashing. Keep the faceplate in its casing while detached. The faceplate is a precision piece of equipment and can be damaged by shocks or jolts. To prevent deterioration, do not touch the terminals of the unit and faceplate with your fingers. How to reset your unit If this unit fails to operate properly, press the reset button.
Loading slot Detaches the faceplate Ejects the disc Display window Auxiliary input jack .u a Volume knob The following indicator lights up when... ST: A stereo broadcast is received (FM). IN: A disc is in the unit. TI: Traffic Information function is turned on. RDS: RDS service is available. When you press or hold the following button(s)... General operation Turns on. Turns off if pressed and held. Selects the available sources (TUNER, CD, AUX, STANDBY), if the power is SRC turned on.
Getting started The display demonstration is always turned on unless you cancel it. When you turn on the power (or after you reset the unit), the display shows: [CANCEL DEMO] \ [PRESS] \ [VOLUME KNOB] Setting the demonstration mode 1 Press the volume knob to enter [FUNCTION] mode. 2 Turn the volume knob to select [SETTINGS], then press to enter. 3 Turn the volume knob to select [CLOCK], then press to enter. 4 Turn the volume knob to select [CLOCK ADJ], then press to enter.
ENGLISH 1 Press SRC to select “TUNER.” 2 Press BAND repeatedly to select a band (FM1/ FM2/ FM3/ MW/ LW). 3 Press 4 / ¢ to search for a station. Adjust [SETTINGS] mode settings While listening to the radio... 1 Press the volume knob to enter [FUNCTION] mode. 2 Turn the volume knob to select [SETTINGS], then press to enter. 3 Turn the volume knob to make a selection, then press to confirm. See table below for selection. 4 Hold to finish the procedure.
Listening to a disc Ejects the disc. (“NO DISC” appears and “IN” indicator goes off.) Press to select track/file. Hold to fast-forwards/reverses. Press to select folder. m .u a 1 Press SRC to turn on the power. 2 Insert a disc into the loading slot. Playback starts automatically. 3 Press to resume/pause playback (if necessary). Selecting Repeat Play Selecting Scan Play Press number button 2 (SCAN) repeatedly to make a selection. co Press number button 4 (REP) repeatedly to make a selection. 13 0.
ENGLISH Discs that cannot be used Discs that are not round. Discs with coloring on the recording surface or discs that are dirty. You cannot play a Recordable/ReWritable disc that has not been finalized. (For the finalization process refer to your disc writing software, and your disc recorder instruction manual.) 3-inch CD cannot be used. Attempt to insert using an adapter can cause malfunction. Listening to the other external components co m .
Function settings 1 Press the volume knob to enter [FUNCTION] mode. 2 Turn the volume knob to select [AUDIO CTRL] or [SETTINGS], then press to enter. 3 Turn the volume knob to make a selection, then press to confirm. See table below for selection. Repeat step 3 until the desired item is selected/activated. Press to return to the previous item. 4 Hold to finish the procedure. [AUDIO CTRL] : While listening to any source except in STANDBY state... 13 0. co m .
Item AUX NAME CLOCK DISPLAY RDS SET Selectable setting (Preset: *) AUX */ DVD/ PORTABLE/ GAME/ VIDEO/ TV: Selects the desired name for the connected component. (Selectable only if “AUX” is selected as the source.) CLOCK ADJ: (For details, see page 6.) TIME SYNC: ON *: Synchronizes the RDS station time data and the unit's clock. ; OFF: Cancels. DIMMER SET: ON: Dims the display illumination. ; OFF *: Cancels.
Installation/connection (×1) (×1) (×1) (×1) (×1) (×2) Basic procedure If your car's ignition does not have an ACC position, connect the ignition wires to a power source that can be turned on and off with the ignition key. If you connect the ignition wire to a power source with a constant voltage supply, as with battery wires, the battery may die. Do not use your own screws. Use only the screws provided. Install this unit in the console of your vehicle.
ENGLISH Wiring connection For KDC-3051R/ KDC-3051G/ KDC-315A/ KDC-315R/ KDC-3251RY KDC-3051R/ KDC-3051G/ KDC-315A/ KDC-315R KDC-3251RY Front output terminals Rear/subwoofer output terminals Rear/subwoofer output terminals Fuse (10 A) Antenna terminal (JASO) KDC-3051R/ KDC-3051G/ KDC-315A/ KDC-315R: To the steering wheel remote control adapter (optional accessory) Blue/White (Power control/motor antenna control wire) To the power control terminal when using the optional power amplifier, or to the ante
For KDC-3051RY/ KDC-3051GY Fuse (10 A) Antenna terminal (JASO) White (+) / White/black (–) : To front speaker (left) Gray (+) / Gray/black (–) : To front speaker (right) Green (+) / Green/black (–) : To rear speaker (left) Purple (+) / Purple/black (–) : To rear speaker (right) To the antenna control terminal in the vehicle. Blue/White (Power control wire) To the power control terminal when using the optional power amplifier.
ENGLISH Removing the unit 1 Detach the faceplate. 2 Engage the catch pin on the removal tools into the holes on both sides of the escutcheon, then pull it out. 3 Insert the removal tools deeply into the slots on each side, then follow the arrows instructions as shown on the right. Specifications Subject to change without notice. FM tuner section Audio section MW tuner section 13 0. .