DDX4028BT DDX4058BT DDX3028 DDX3058 MONITOR WITH DVD RECEIVER INSTRUCTION MANUAL © 2010 Kenwood Corporation All Rights Reserved. Cov_DDX_Europe_EN.
Contents Before use ...................................... 3 How to reset your unit .............................................3 INTRODUCTIONS Initial Settings ............................... 5 Initial setup ......................................................................5 Setting the security function ...............................6 Component names and functions .................................. 7 Setting the clock ............................ 8 Common operations .....................
Before use WARNINGS: (To prevent accidents and damage) • DO NOT install any unit or wire any cable in a location where; – it may obstruct the steering wheel and gearshift lever operations. – it may obstruct the operation of safety devices such as air bags. – it may obstruct visibility. • DO NOT operate the unit while driving. If you need to operate the unit while driving, be sure to look around carefully. • The driver must not watch the monitor while driving. For safety...
This Product is not installed by the manufacturer of a vehicle on the production line, nor by the professional importer of a vehicle into an EU Member State. Information on Disposal of Old Electrical and Electronic Equipment and Batteries (applicable for EU countries that have adopted separate waste collection systems) Products and batteries with the symbol (crossed-out wheeled bin) cannot be disposed as household waste.
INTRODUCTIONS Initial Settings Initial setup 2 Finish the procedure. When you power on the unit for the first time or reset the unit, the initial setting screen appears. • You can also change the settings on the screen. (☞ page 38) 1 Language Select the text language used for on-screen information. (☞ page 40) AV Input Select the use of the AV-IN input terminal— or . (☞ page 40) R-CAM Interrupt Select when connecting the rear view camera.
Setting the security function You can set a security code to protect your receiver system against theft. • When is activated (☞ right column), the code cannot be changed. 2 Enter a four-digit number (1), then confirm the entry (2). Deletes the last entry Registering the security code 1 Display the security code setting screen. On : Cancels the setting 3 Repeat step 2 to confirm your security code. Now, your security code is registered.
Component names and functions Screen (touch panel) Monitor panel 1 Loading slot 2 0 (Eject) button Ejects the disc. 3 Remote sensor 4 Reset button/Power indicator/Security indicator • Resets the unit. (☞ page 3) • Lights up while the unit is turned on. • Flashes when the security function is activated. (☞ page 6) 5 MENU/ button • Turns off the power. (Hold) • Turns on the power. (Press) • Displays screen. (Press) (☞ page 10) 6 AV/AV OUT button • Displays the current source screen.
Setting the clock 1 Display screen. 4 Set the clock time.
Common operations Turning on the power Putting the unit in standby Turning off the power (Hold) Adjusting the volume To adjust the volume (00 to 35) Decrease Increase To attenuate the sound Turning off/on the screen DDX4028BT/ DDX4058BT DDX3028/ DDX3058 The ATT indicator lights up. To cancel the attenuation, press the volume adjustment knob. (Hold) (Hold) The screen is turned off. To turn on the screen, press MENU/ . English EN_DDX_E.
Switching screens Source control screen * Appears only when Displays the navigation screen. * (☞ page 30) • Changes the AV source. • Displays the screen. a navigation unit is connected. Changes the detailed settings. You can select 3 items to be displayed in this area. (☞ page 39) Changes the page ☞ page 9 Press [ ] to return to the previous screen. Touch screen operation Displays the video control menu. Goes to the previous chapter/track.
AV SOURCE OPERATIONS Selecting the playback source DDX4028BT/DDX4058BT DDX3028/DDX3058 *1 NAV (☞ page 30) DISC (☞ page 12) TEL *3 (☞ page 46) USB (☞ page 19) iPod *4 (☞ page 21) TUNER (☞ page 24) VIDEO *4 (☞ page 29) Bluetooth*3 (☞ page 49) *1 *2 *3 *4 Displays the navigation screen when a navigation unit is connected. *2 Plays a disc. Displays the Bluetooth mobile phone setting screen. Plays files on a USB device. Plays an iPod/iPhone. Switches to the radio broadcast.
Disc operations Playing a disc • If a disc does not have any disc menu, all tracks on it will be played repeatedly until you change the source or eject the disc. Inserting a disc To eject a disc Label side • You can eject a disc when playing another AV source. • If the ejected disc is not removed within 15 seconds, the disc is automatically inserted again into the loading slot to protect it from dust. The source changes to “DISC” and playback starts.
Playable disc type Disc type Recording format, file type, etc Playable 1 DVD DVD-Video * Region Code: • For DDX4028BT/DDX3028: 2 • For DDX4058BT/DDX3058: 5 DVD Recordable/ Rewritable (DVD-R/-RW *2, +R/+RW *3) • DVD Video: UDF bridge • DVD-VR • DivX/MPEG1/MPEG2/ JPEG/MP3/WMA/WAV/ AAC: ISO 9660 level 1, level 2, Romeo, Joliet DVD-Video Dual Disc DVD side CD/VCD DTS-CD/Audio CD/CD Text (CD-DA) DVD-Audio/DVD-ROM DVD-VR *4 DivX/MPEG1/MPEG2 JPEG MP3/WMA/WAV/AAC MPEG4/DVD+VR/DVD-RAM Non-DVD side VCD
Playback operations To display the source control screen (☞ below) • Pressing FNC/R-CAM hides the operation buttons. • The operation buttons disappear by touching the screen or or when no operation is done for about 5 seconds. For DVD/DVD-VR/VCD/DivX/MPEG1/MPEG2/JPEG Playing time Media type • DVD Video: Title no./Chapter no. • DVD-VR: Program no. (or Playlist no.)/Chapter no.*1 • DivX/MPEG1/MPEG2/JPEG: Folder no./Track no. • VCD: Track no.
To display the source control screen (☞ below) • Pressing FNC/R-CAM hides the operation buttons. • The operation buttons disappear by touching the screen or or when no operation is done for about 5 seconds. For CD/MP3/WMA/WAV/AAC Track/file information • Touching [<] scrolls the text if all the text is not shown. Media type Playing time Playback status (3: play / 8: pause ) • MP3/WMA/WAV/AAC: Folder no./Track no. • CD: Track no.
Video menu operations You can display the video menu screen while watching the playback pictures on the screen. • Available items on the screen differ depending on the types of the loaded disc and playback files. • The operation buttons disappear by touching the screen or when no operation is done for about 5 seconds. • The screen for MPEG1/MPEG2 differs from the above. 16 [Audio] Selects the audio type. • For DVD-VR: Selects the audio channel (ST: stereo, L: left, R: right).
• To deactivate the PBC function, press [7] then the direct selecting buttons to select a track number. Only for VCD 1 Selecting playback mode For DVD/DVD-VR 2 Selects Repeat playback mode For VCD (without PBC)/CD/DivX/MPEG1/ MPEG2/MP3/WMA/WAV/AAC Direct selecting buttons (☞ below) [Audio] [Return] [MENU] [Picture Adjust] [Aspect] [ZOOM] [Direct] Selects the audio channel (ST: stereo, L: left, R: right). Displays the previous screen or the menu. Displays the disc menu.
Settings for disc playback For DVD/DVD-VR Disc Setup items Selectable setting/item Initial: Underlined Menu Language Select the initial disc menu language; Initial English (☞ page 53). Subtitle Language Select the initial subtitle language or erase the subtitle (OFF); Initial English (☞ page 53). Audio Language Select the initial audio language; Initial English (☞ page 53).
USB operations Playing a USB device • This unit can play JPEG/DivX/MPEG1/ MPEG2/MP3/WMA/WAV/AAC files stored in USB mass storage class device. • This unit can recognize a total of 5 000 files and 250 folders (a maximum of 999 files per folder). • Make sure all important data has been backed up to avoid losing the data. Connecting a USB device You can connect a USB mass storage class device such as a USB memory, Digital Audio Player etc. to the unit.
To display the source control screen (☞ below) • Pressing FNC/R-CAM hides the operation buttons. • The operation buttons disappear by touching the screen or or when no operation is done for about 5 seconds. • To change settings for video playback, ☞ page 35. While playing, “Jacket picture” is shown if the file has the tag data including “Jacket picture.” Track/file information (for MP3/WMA/WAV/ AAC) • Touching [<] scrolls the text if all the text is not shown.
Listening to the iPod/iPhone device Preparation Connecting iPod/iPhone Settings for iPod playback When the source is “iPod”... To iPod/iPhone • Use the following cables: – To listen to the music (digital): USB Audio cable for iPod/iPhone—KCA-iP102 (optional accessory) – To watch the video and to listen to the music (analog): USB Audio and Video cable for iPod/iPhone—KCA-iP22F (optional accessory) (☞ INSTALLATION MANUAL) • Do not use extension cables.
iPod/iPhone playback operations To display the source control screen (☞ below) • Pressing FNC/R-CAM hides the operation buttons. • The operation buttons disappear by touching the screen or or when no operation is done for about 5 seconds. • To change settings for video playback, ☞ page 35. • The operations explained in this manual are under the condition when the unit is selected for controlling playback. (☞ below) Song/video information • Touching [<] scrolls the text if all the text is not shown.
Selecting a track/video from menu on the iPod/iPhone Video menu: 1 Switches between Music ( ) and Video ( ) 2 Select the menu (Music or Video) (1), a category (2), then a desired item (3). • Select the item in the selected layer until a desired track starts playing. • Available categories differ depending on the type of your iPod/iPhone. Music menu: Switches between Music ( ) and Video ( ) Returns to the previous layer Returns to the top layer English EN_AVsource.
Listening to the radio The station frequency currently tuned in/ PS (station name) for FM Radio Data System when PS signal is coming in Preset list Standby reception indicators (☞ page 27) RDS indicator ☞ page 30 ST indicator LO.S indicator (☞ page 25) AF indicator (☞ page 28) Seek mode indicator • The ST indicator lights up when receiving an FM stereo broadcast with sufficient signal strength. [P1] – [P6] [Mode] [TI] [Mono]* [Text] • Turns in the preset station.
Displaying the information of the current station Storing stations in memory You can preset six stations for each band. Automatic presetting—AME (Auto Memory) 1 2 (Hold) Hides the text information Text information Scrolls the text information To tune in FM stations only with strong signals—Local Seek 1 Local stations with the strongest signals are searched and stored automatically. Manual presetting 1 Tune in to a station you want 2 to preset. (☞ page 24) Select a preset number.
Selecting a preset station The following features are available only for FM Radio Data System stations. Searching for FM Radio Data System program—PTY Search You can search for your favorite programs being broadcast by selecting the PTY code for your favorite programs. 1 2 Select a PTY code. (Hold) Changes the page PTY Search starts. If there is a station broadcasting a program of the same PTY code as you have selected, that station is tuned in.
Activating/deactivating TI/News Standby Reception TI Standby Reception News Standby Reception 1 TI indicator TI indicator TI Standby Reception Lights in white The unit will temporarily switch to Traffic Information (TI) if available. Lights in orange Not yet activated. Tune in to another station providing the Radio Data System signals. Goes off Deactivated. • The volume adjustment for Traffic Information is automatically memorized.
Tracing the same program— Network-Tracking Reception When driving in an area where FM reception is not sufficient enough, this unit automatically tunes in to another FM Radio Data System station of the same network, possibly broadcasting the same program with stronger signals. When shipped from the factory, NetworkTracking Reception is activated.
Using other external components To display the source control screen (☞ below) • Pressing FNC/R-CAM hides the operation buttons. • The operation buttons disappear by touching the screen or or when no operation is done for about 5 seconds. • To change settings for video playback, ☞ page 35. AV-IN name ( ☞ below) ☞ page 30 [Mode] [MENU] Changes the AV-IN name. • Press [2] or [3] to select an AV-IN name. • This setting does not affect the source name “VIDEO” displayed on .
Using the external navigation unit You can connect a navigation unit (KNA-G620T, KNA-G630: optional accessory) to the navigation input terminal so that you can view the navigation screen. (☞ INSTALLATION MANUAL) The navigation guidance comes out through the front speakers even when you listen to an audio source. To view the navigation screen 2 On : or On any screen: 3 The navigation screen is activated.
Sound adjustment Using the sound equalization • The adjustment is memorized for each source until you adjust sound again. If the source is a disc, the adjustment is stored for each of the following categories. – DVD/DVD-VR – VCD/CD – DivX/MPEG1/MPEG2/MP3/WMA/WAV/AAC • You cannot adjust the sound when the unit is in standby. Selecting a preset sound mode 1 On : Storing your own adjustment Customizing preset sound mode 1 Select a sound mode.
Adjusting the sound precisely 1 Perform steps 1 and 2 of “Selecting a preset sound mode,” then... Adjusting the cross over frequency 1 On : 2 2 3 Adjust the sound of each band. Flat Freq Level Q Factor Bass EXT SW Level 3 Select the item to adjust, then make adjustment. Adjusts the cross over for front or rear speakers (high pass filter). Changes level of Bass/ Middle/Treble to 0. Selects frequency. Adjusts level. Adjusts the width of the frequency. Activates/deactivates bass.
Changing the display design You can change the background and panel color. 1 To select a panel color On : Variable color illumination • Illumination color changes gradually. 2 For making your own color adjustment, ☞ below Making your own color adjustment • You can make your own color adjustment only when is selected. 3 Select an item to change 1 ( or ). 2 4 Select a background/panel color.
Using your favorite scene as the background While playing a video or JPEG, you can capture an image and use the captured image as a background. • You cannot capture copyrighted content. • When using JPEG file as the background, make sure that the resolution is 800 x 600 pixels. • The color of the captured image may look different from that of the actual scene. 1 Play back a video or JPEG. 2 Display . (☞ page 33) 3 4 Adjust the image. [38]*1 Starts playback/pauses.
Setting for video playback You can change the setting for video playback. Picture adjustment You can adjust the picture quality. 1 Display the adjustment menu. 3 Adjust the picture (–15 to +15). Adjusts the brightness Adjusts the contrast Adjusts the black Adjusts the color Adjusts the tint* Adjusts the sharpness * Adjustable only when the incoming signal is NTSC. 2 Select dimmer on () or off (). English EN_DDX_E.
Changing the aspect ratio You can change the aspect ratio for video playback. 1 * While DivX is played back with set to <16:9> (for disc: ☞ page 18/ for USB: ☞ page 20), the aspect ratio is not set correctly. Zooming picture You can zoom the picture ( to ). • When is set to or (☞ left column), the picture is zoomed with the aspect ratio of the setting.
Using a rear view camera • To use a rear view camera, the REVERSE lead connection is required. For connecting a rear view camera, see the INSTALLATION MANUAL. Activating the rear view camera 1 On : Displaying the picture from the rear view camera The rear view screen is displayed when you shift the gear to the reverse (R) position. 2 To display the picture from the rear view camera manually 3 (Hold) To deactivate, select .
Setting menu items • You cannot change
Menu item Dimmer Selectable setting/item ♦ Auto ♦ ON ♦ OFF ♦ NAV : Dims the screen and button illumination when you turn on the headlights. • The ILLUMI lead connection is required. (☞ INSTALLATION MANUAL) : Activates dimmer. : Cancels. : Activates or deactivates dimmer according to the day/night display setting of the connected navigation unit. User Customize Change the display design (background and panel color).
Input Menu item Selectable setting/item You can determine the use of AV-IN input terminal. ♦ AV-IN : Select to play an AV component connected to the AV-IN input terminal. ♦ iPod : Select when connecting the iPod/iPhone using the USB Audio and Video cable for iPod/iPhone. (☞ page 21) R-CAM Interrupt ♦ ON Navigation Change the navigation settings. (☞ page 30) Language * Select the text language used for on-screen information.
Memorizing/recalling the settings You can memorize the settings changed in the menu and recall the memorized settings anytime. • The memorized settings are kept even when the unit is reset. 1 Locking the settings You can lock the settings to prevent them from being changed. • is shown beside the settings that can be locked. 1 On : On : 2 2 To unlock the setting, press [Unlock]. Adjusting the touch position • To cancel, press [No]. 3 Select an operation.
BLUETOOTH OPERATIONS (Only for DDX4028BT/DDX4058BT) Information for using Bluetooth® devices • While driving, do not perform complicated operation such as dialing the numbers, using phone book, etc. When you perform these operations, stop your car in a safe place. • Some Bluetooth devices may not be connected to this unit depending on the Bluetooth version of the device. • This unit may not work for some Bluetooth devices. • Connecting condition may vary depending on circumstances around you.
Connecting Bluetooth devices For connecting a Bluetooth audio player Connecting a new Bluetooth device for the first time When you connect a Bluetooth device to the unit for the first time, make pairing between the unit and the device. Pairing allows Bluetooth devices to communicate each other. To make pairing, you may need to enter the PIN (Personal Identification Number) code of your Bluetooth device you want to connect.
To disconnect Cancel 5 Operate the Bluetooth device A confirmation message appears. Press [Yes]. to connect. “Connected” appears. Press [OK] to confirm the operation. Now connection is established and you can use the Bluetooth device through the unit. Deleting a registered Bluetooth device 1 On (☞ Step 2 on the left column): Connecting/disconnecting a registered Bluetooth device 1 Display the Bluetooth setting screen.
Using the Bluetooth mobile phone Receiving a call When a call comes in/making a call... Ends/rejects the call Call information (if acquired) Status of the device/Battery reminder (only when the information comes from the device) • Phone operation is not available while the picture from the rear view camera is displayed. (☞ page 37) When is set to The unit answers the incoming call automatically.
1 Making a call Using the phone book/call lists On : 1 2 Select a method to make a call. Call lists/phone book (☞ the right column) Direct number entry (☞ below) Preset list (For presetting, ☞ page 47) Voice dialing (☞ the right column) Outgoing From dialled call list. Incoming Missed Phonebook From received call list. From missed call list. From phone book. • For copying the phone book, ☞ page 47.
Presetting the phone numbers You can preset up to 6 phone numbers. 1 On : Copying the phone book You can copy the phone book memory of a mobile phone into the unit (up to 400 memories). 1 2 Select an item from phone book/call lists. On : 2 3 3 Select a phone number. (Hold) 4 Select a preset number to store. • You can also preset the phone number entered on screen by pressing [Preset].
Deleting the phone number memory in the unit 1 Display the phone book/call list you want to delete. (☞ page 46) 2 About mobile phone compatible with Phone Book Access Profile (PBAP) If your mobile phone supports PBAP, the phone book and call lists are automatically copied to the unit when the mobile phone is connected.
Using the Bluetooth audio player • To register a new device, ☞ page 43. • To connect/disconnect a device, ☞ page 44. Tag data (current track title/ artist name/album title) * • Touching [<] scrolls the text if all the text is not shown. Playing time * Playback status * (3: play / 8: pause) ☞ page 30 Battery reminder (only when the information comes from the device) • The operation buttons, indications and information displayed on the screen differ depending on the connected device.
Menu items Selectable setting/item Initial: Underlined Connection ♦ Connect : ☞ page 44 ♦ Disconnect : ☞ page 44 PIN Code Changes the PIN code of the unit. • Touch the current PIN code, enter a new PIN code, then press [Enter]. Device Name Shows the device name to be shown on the Bluetooth device — “KENWOOD BT MM-5U2.” Device Address Shows the MAC address of the unit. Phone Device*1 Shows the phone device name. Audio Device*2 Shows the audio device name.
REFERENCE Maintenance Caution on cleaning the unit Do not use any solvent (for example, thinner, benzine, etc.), detergent, or insecticide. This may damage the monitor or the unit. Recommended cleaning method: Gently wipe the panel with a soft, dry cloth. Moisture condensation Moisture may condense on the lens inside the unit in the following cases: • After starting the heater in the car. • If it becomes very humid inside the car. Should this occur, the unit may malfunction.
More about this unit File playback Playing DivX files • This unit can play back DivX files with the extension code <.divx>, <.div>, or <.avi> (regardless of the letter case—upper/ lower). • Audio stream should conform to MP3 or Dolby Digital. • The file encoded in the interlaced scanning mode may not be played back correctly. • The maximum bit rate for video signals (average) is 4 Mbps (for discs)/2 Mbps (for USB).
Sound signals emitted through the rear terminals Through the analog terminals (Speaker out/Front Preout/Rear Preout) 2-channel signal is emitted. When playing multi-channel encoded disc, multi-channel signals are downmixed.
Troubleshooting What appears to be trouble is not always serious. Check the following points before calling a service center. • For operations with the external components, refer also to the instructions supplied with the adapters used for the connections (as well as the instructions supplied with the external components). If the following messages appear Message Remedy/Cause “No Signal” • Start the playback on the external component connected to AV-IN input terminal. • Check the cords and connections.
If there seems to be a problem iPod/iPhone AV-IN DivX/MPEG1/MPEG2/ JPEG/MP3/WMA/WAV/AAC Disc in general TUNER General Symptom Remedy/Cause No sound comes out of the speakers. • Adjust the volume to the optimum level. • Check the cords and connections. No picture is displayed on the screen. Turn on the screen. (☞ page 9) The unit does not work at all. Reset the unit. (☞ page 3) The remote controller* does not work. Replace the battery. AME automatic presetting does not work.
Bluetooth (only for DDX4028BT/DDX4058BT ) USB iPod/iPhone Symptom Remedy/Cause Sound is distorted. Deactivate the equalizer either on this unit or the iPod/iPhone. A lot of noise is generated. Turn off (uncheck) the “VoiceOver” feature of the iPod. For details, visit . No operations are available when playing back a track containing Artwork. Operate the unit after the Artwork is loaded. (☞ page 21) “Reading...” keeps flashing on the Turn off the power and on again. screen.
Specifications Monitor section Picture Size : 6.1 inches (diagonal) wide : 136.2 mm (W) × 72 mm (H) Display System : Transparent TN LCD panel Drive System : TFT active matrix system Number of Pixels : 1,152,000 (800H × 480V × RGB) Effective Pixels : 99.
FM tuner section Frequency Range (50 kHz) : 87.5 MHz – 108.0 MHz Usable Sensitivity (S/N: 26 dB) : 0.7 μV/75 Ω Quieting Sensitivity (S/N: 46 dB) : 1.6 μV/75 Ω Frequency Response (± 3.
• Manufactured under license under U.S. Patent #’s: 5,451,942; 5,956,674; 5,974,380; 5,978,762; 6,487,535 & other U.S. and worldwide patents issued & pending. DTS and the Symbol are registered trademarks, & DTS 2.0+ Digital Out and the DTS logos are trademarks of DTS, Inc. Product includes software. © DTS, Inc. All Rights Reserved. • Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories. • The “AAC” logo is a trademark of Dolby Laboratories.
KS-UBT1 (USB Bluetooth Adapter) Instruction Manual CAUTION Changes or modifications not approved by Kenwood could void the user’s authority to operate the equipment. • This adapter has been designed exclusively for use with Kenwood car receivers. Do not use this adapter with any other car receiver. For details, see also the Instructions supplied with your receiver. • The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Kenwood Corporation is under license.
Declaration of Conformity with regard to the R&TTE Directive 1999/5/EC Manufacturer: Kenwood Corporation 2967-3 Ishikawa-machi, Hachioji-shi, Tokyo, 192-8525 Japan EU Representative’s: Kenwood Electronics Europe BV Amsterdamseweg 37, 1422 AC UITHOORN, The Netherlands English Hereby, Kenwood declares that this unit KS-UBT1 is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.
Cov_DDX_Europe_EN.
