MONITOR WITH DVD RECEIVER DDX6036 DDX6036M INSTALLATION MANUAL © B54-4756-00 (MW/M2W) B54-4756-00_00_DDX6036_En.indd 1 09.10.
Accessories 1 9 ..........1 ..........1 2 ..........1 3 ..........1 4 ..........2 5 ..........1 6 ..........1 7 ..........6 8 ..........6 2 | DDX6036/DDX6036M B54-4756-00_00_DDX6036_En.indd 2 09.10.
Installation Procedure 1. To prevent a short circuit, remove the key from the ignition and disconnect the - battery. 2. Make the proper input and output wire connections for each unit. 3. Connect the speaker wires of the wiring harness. 4. Connect the wiring harness wires in the following order: ground, battery, ignition. 5. Connect the wiring harness connector to the unit. 6. Install the unit in your car. 7. Reconnect the - battery. 8. Press the reset button. 9. Perform the Initial Setup.
Connection you connect the ignition wire (red) and the battery ¤ Ifwire (yellow) to the car chassis (ground), you may Ignition key switch cause a short circuit, that in turn may start a fire. Always connect those wires to the power source running through the fuse box.
Cooling fan FUSE ( 15A ) Accessory 1 REVERSE REMOTE CONT STEERING WHEEL REMOTE INPUT White/Black White + To front left speaker Gray/Black ILLUMI + To front right speaker Gray MUTE Green/Black Green + To rear left speaker Purple/Black ANT. CONT Purple + To rear right speaker P.CONT English | B54-4756-00_00_DDX6036_En.indd 5 5 09.10.
System Connection USB terminal USB device (commercially available) Audio input (iPod/AV Input 2 switchable) Resistance-free stereo type mini plug (3.5φ) Visual input (iPod/AV Input 2 switchable) Resistance-free mini plug (3.
Optional Accessory Connection iPod (commercially available) KCA-iP301V (Optional Accessory) Visual Output (Yellow) Audio Output (Black) USB terminal KCA-BT200 (Optional Accessory) USB terminal Connection cable (Included in the KCA-BT200) Navigation System (Optional Accessory) 123 Type Switch 123 TV Tuner (Optional Accessory) TV ANTENNA INPUT Connection cable (Included in the Navigation System) TO MONITOR UNIT units that can be connected to this unit.
Installing the Escutcheon For General Motors For Toyota/Scion 1. Cut out accessory 5 to meet the shape of the opening of the center console. 2. Attach accessory 5 to the unit. 1. Cut out accessory 5 as illustrated. Cutting line Cut out to meet the shape of the opening in the vehicle. Accessory 5 Accessory 5 2. Fold double-sided adhesive (accessory 6) along the slit and attach it to accessory 5 cut-out against the center rib as illustrated. Use 2 pieces of accessory 6 for 1 accessory 5 cut-out. 3.
Installation for Monitor/Player Unit Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place. ⁄ Make sure that the unit is installed securely in place. If the unit is unstable, it may malfunction (eg, the sound may skip). Installation on Toyota, Nissan or Mitsubishi Car using Brackets Accessory 7 (M5x6mm) or Accessory 8 (M5x7mm) Car Bracket Accessory 7 (M5x6mm) or Accessory 8 (M5x7mm) English | B54-4756-00_00_DDX6036_En.indd 9 9 09.10.
Removing Monitor/Player Unit Removing the Hard Rubber Frame (escutcheon) 1. Engage the catch pins on the removal tool 4 and remove the two locks on the lower level. Lower the frame and pull it forward as shown in the figure. Removing the Unit 1. Remove the hard rubber frame by referring to the removal procedure in the section . 2. Insert the two removal tools 4 deeply into the slots on each side, as shown.
B54-4756-00_00_DDX6036_En.indd 11 09.10.
B54-4756-00_00_DDX6036_En.indd 12 09.10.
