ENGLISH INSTRUCTION MANUAL MONITOR WITH DVD RECEIVER MONITOR WITH RECEIVER DDX795 (Region 1 – DVD Region Code 1 Area) DDX775BH (Region 1 – DVD Region Code 1 Area) DDX6018BT (Region 4 – DVD Region Code 4 Area) DDX5018BT (Region 4 – DVD Region Code 4 Area) DDX595 (Region 1 – DVD Region Code 1 Area) DDX575BT (Region 1 – DVD Region Code 1 Area) DDX718WBTL (Region 4 – DVD Region Code 4 Area) DMX6018BT DMX718WBTL This instruction manual is used to describe the models listed above.
Important Notice To ensure proper use, please read through this manual before using this product. It is especially important that you read and observe WARNINGS and CAUTIONS in this manual. Please keep the manual in a safe and accessible place for future reference. WARNINGS To prevent accidents and damages • DO NOT install any unit or wire any cable in a location where; – it may obstruct the steering wheel and gearshift lever operations. – it may obstruct the operation of safety devices such as air bags.
Important Notice For DDX795/DDX775BH/DDX595/DDX575BT: CAUTION This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines and RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment has very low levels of RF energy that is deemed to comply without maximum permissive exposure evaluation (MPE).
About this manual The displays and panels shown in this manual are examples used to provide clear explanations of the operations. For this reason, they may be different from the actual displays or panels. Illustrations of DDX795 are mainly used for explanation. Contents Component Names and Operations ............... 3 Basic Operations ................................................. 5 Turning on the power ..................................................................
Component Names and Operations DDX795/DDX775BH/DDX6018BT DMX6018BT 6 HOME button • (Press): Turns on the power. • (Hold): Turns off the power or AV source.*2 • HOME (Press): Displays the Home screen while the power is on. 7 MENU/ATT button • MENU (Press): Pops up the short-cut menu. • ATT (Hold): Attenuates the sound. 8 /VOICE button • (Press): Displays the App screen. (Page 19) • VOICE (Hold): Activates the voice dialing. 9 DDX795/DDX775BH/DDX6018BT: M button Displays the screen.
Component Names and Operations DDX595/DDX575BT p Volume/MENU/ATT knob • Volume (Turn): Adjusts the audio volume. • MENU (Press): Pops up the short-cut menu. • ATT (Hold): Attenuates the sound. DDX718WBTL 1 Remote sensor*1 2 Power indicator/Security indicator • Lights up while the unit is turned on. • Flashes when the security function is activated. 3 M button 4 Loading slot 5 Screen (touch panel) 6 Monitor panel 7 HOME button • (Press): Turns on the power. • (Hold): Turns off the power or AV source.
Basic Operations Turning on the power DDX795 DDX775BH DDX6018BT DMX6018BT Putting the unit in standby DDX5018BT DDX595 DDX575BT DDX718WBTL DMX718WBTL 1 Display the source/option selection screen. 2 On the pop-up short-cut menu, touch as follows: Display OFF On the Home screen, touch as follows: To turn on the screen: Touch the screen. On the monitor panel 2 Turning off the power/turning off the AV source Put the unit in standby.
Basic Operations DDX795 DDX775BH DDX6018BT DMX6018BT DDX5018BT 2 Attenuating the sound Adjusting the volume DDX718WBTL DMX718WBTL You can adjust the volume (00 to 40) by pressing J to increase and pressing K to decrease. • Holding J increases the volume continuously to level 15. DDX595/DDX575BT Perform the adjustment or operation. (Only for DDX795/DDX775BH/DDX595/DDX575BT/ DDX6018BT/DMX6018BT/DDX718WBTL/ DMX718WBTL) DDX795 DDX775BH DDX6018BT DMX6018BT DDX595 DDX575BT DDX718WBTL DMX718WBTL E.g.
Getting Started Initial settings When you power on the unit for the first time, the screen appears. Perform the initial settings. E.g. Initial settings screen for DDX795 Once completed, a warning message appears. Touch [Agree] to display the Home screen. [Language]*1 Select the text language used for on-screen information. Touch [Language Select], then select the language.
Getting Started Activating the security function 2 On the Home screen, touch as follows: (Only for DDX5018BT/DDX595/DDX575BT) You can activate the security function to protect your receiver system against theft. 1 Display the screen. You can display or change to other screens at any time to show information, change the AV source, change the settings, etc. Display the screen. Then, on the screen, touch [User Interface].
Various Screens and Operations Home screen When you turn on the power for the first time, the Home screen appears. • You can customize the Home screen. • To display the Home screen from other screens, press HOME on the monitor panel. Available playback sources and options [DISC]*4 Plays a disc. • For sources and information displayed when an ADS adapter is connected, see page 39.*1 [iPod] Plays an iPod/iPhone. [USB] Plays files on a USB device. Touch 5 to display the source/option selection screen.
Various Screens and Operations Customizing the source/option selection screen You can arrange the items to display on the source/ option selection screen. 1 Select an item to move. Touch and hold the item you want to move until boxes appear around the icons. 2 Source control screen You can perform the playback operation from the source control screen during playback. • The operation keys and information displayed vary depending on the selected source/disc type/file type being played.
Various Screens and Operations Common operation keys on source control screen • The appearance of the operation keys may differ, however the similar operation keys have the same operations. • Available operation keys differ depending on the selected source or connected device. Touching the operation keys performs the following actions: 4 [ [ ]* ]* Selects repeat playback mode.
Various Screens and Operations 2 Select an item to jump. E.g. Pop-up short-cut menu screen for DDX795 1 Displays the picture adjustment screen. (Page 15) 2 Turns off the screen. 3 Camera (for DDX795/DDX775BH/DDX6018BT/ DMX6018BT/DDX5018BT/DDX595/DDX575BT): Displays the picture from the connected rear view camera. (Page 36) Angle (for DDX718WBTL/DMX718WBTL): Displays the screen. (Page 6) 4 Displays the screen. (Page 50) 5 Displays the sound adjustment screen.
Disc (Only for DDX795/DDX775BH/DDX6018BT/DDX5018BT/DDX595/DDX575BT/DDX718WBTL) • If a disc does not have a disc menu, all tracks on it will be played repeatedly until you change the source or eject the disc. • For playable disc types, file types and other information, see pages 66 and 67 . • If “ ” appears on the screen, the unit cannot accept the operation you have tried to do. – In some cases, without showing “ ”, operations will not be accepted.
Video Disc Settings for disc playback • Available items shown on the screen differ depending on the type of disc/file being played back. 1 Display the screen. On the source control screen, touch as follows: 2 Make the settings. [Menu Language]* Select the initial disc menu language. (Initial: English) [Subtitle Language]* Select the initial subtitle language or turn subtitles off (OFF). (Initial: English) [Audio Language]* Select the initial audio language.
Video Video menu control operations (Only for DDX795/DDX775BH/DDX6018BT/ DDX5018BT/DDX595/DDX575BT/DDX718WBTL) You can display the video menu control during video playback. • Available operation keys differ depending on the selected disc type and file type. 1 Touching the operation keys performs the following actions: [Top] Displays the top menu (DVD). [Menu] Displays the disc menu (DVD). [Return] Returns to the previous screen. [Enter] [Highlight] Display the video menu control screen.
USB Video Adjusts the brightness of the backlight. (−4 to +4) Adjusts the contrast. (−4 to +4) Adjusts the brightness. (−4 to +4) *1 Adjusts the color. (−4 to +4) *2 Adjusts the tint. (−4 to +4) Selects the aspect ratio. • Full: Changes the aspect ratio of video and displays fully on the screen. • Normal: Displays the video in the aspect ratio of 4:3.
iPod/iPhone USB Selecting a folder/track on the list 1 Display the folder/track list. On the source control screen, touch as follows: From
Apps—WebLink™/Waze iPod/iPhone Playback operations Playback information and key operation • For playback information, see “Source control screen” on page 10. • For key operations on the touch panel, see “Common operation keys on source control screen” on page 11. Selecting an audio file from the menu 1 3 Select the desired track. • Repeat the procedure until you select the desired track. • For details about the list operation, see page 12.
HD Radio™ tuner Apps—WebLink™/Waze (Only for DDX795/DDX775BH) Connecting a smartphone Android™ device (commercially available) Start playback iPhone (commercially available) 1 About HD Radio™ Technology Select “WebLink”/“Waze” as the source. • To use WebLink™: Select “WebLink”. • To use Waze: Select “Waze”. 2 Operate on the unit to select App.
HD Radio™ tuner Listening to the HD Radio™ broadcast Playback information on the source control screen FM 01 FM 02 FM 03 FM 04 E.g. HD Radio source control screen for DDX795 1 Displays/hides other available operation keys* 2 Picture or station logo if available 3 Changes the seek mode for [S]/[T] • AUTO1 (Initial): Auto search • AUTO2: Tunes in preset stations one after another • MANUAL: Manual search 4 HD indicator • When receiving a digital HD radio broadcast, the HD indicator lights up in orange.
HD Radio™ tuner 8 [S]/[T] [CHK]/ [CHJ] Storing preset stations in the memory Searches for a station. • The search method differs according to the selected seek mode (see page 20). You can preset 15 stations for FM and 5 stations for AM. Selects a sub-channel when receiving an HD Radio multicast channel. Automatic presetting — AME (Auto Memory) 1 1 1 Select the band, then tune in to a station you want to store. • See “Playback information on the source control screen” on page 20 for details.
Radio HD Radio™ tuner Selecting a preset station 1 Select the band, then display the preset station list. Receiving emergency alert When you receive an emergency alert message, the following screen is displayed. Listening to the radio Playback information on the source control screen On the source control screen, touch as follows: 2 (Only for DDX6018BT/DMX6018BT/DDX5018BT/ DDX595/DDX575BT/DDX718WBTL/DMX718WBTL) FM 01 Select a preset station.
Radio 4 Text information • Touching [<] scrolls the text if not all of the text is shown. • Touching [ ] switches the information (e.g. frequency, PS name, Radio Text, title, artist, etc.). − The availability of the information vary depending on the reception, selected station. 5 Preset list 6 Selects the band (AM/FM) 7 Operation keys* 8 Indicators • TI: Lights up in white when receiving the traffic information, and lights in orange when being standby for Traffic Information Reception.
SiriusXM® Satellite Radio Radio (Only for DDX795/DDX775BH/DDX595/DDX575BT) Selecting a preset station Manual presetting 1 Select the band, then tune in to a station you want to store. 1 • See “Playback information on the source control screen” on page 22 for details. 2 Select the band, then display the preset station list. On the source control screen, touch as follows: Display the preset list. On the source control screen, touch as follows: 2 3 Select a preset station.
SiriusXM® Satellite Radio Activating subscription 1 Check your Radio ID. The SiriusXM Satellite Radio ID is required for activation and can be found by tuning to Channel 0 as well as on the label found on the SiriusXM Connect Vehicle Tuner and its packaging. • The Radio ID does not include the letters I, O, S or F. 2 Activate the subscription. For users in the U.S.A: • Online: Visit
SiriusXM® Satellite Radio Operation keys on source control screen • See also “Common operation keys on source control screen” on page 11. [CHJ]/[CHK] Touching the operation keys performs the following actions: 1 [Direct Channel] Displays the screen. [SETUP] Displays the screen. [Band] Selects the band (SXM1/SXM2/SXM3/ SXM4). [Replay]/ [Live] Switches between replay mode screen and live mode screen.
SiriusXM® Satellite Radio Storing preset channels in the memory You can preset six channels for each band. 1 Selecting a preset channel 1 On the source control screen, touch as follows: 1 Tune in to a channel you want to store. Select the band. On the source control screen, touch as follows: • See “Playback information on the source control screen” on page 25 for details. 2 • You can also display the replay mode screen by touching [IW]. Display the preset list.
SiriusXM® Satellite Radio SiriusXM Satellite Radio features SmartFavorites User stored channels (P1 to P6) of the current band are recognized as SmartFavorites channels. SiriusXM Connect Vehicle Tuner automatically buffers their broadcast content in the background. When you select a SmartFavorite channel, you can rewind and replay up to 30 minutes of any of the missed news, talk, sports or music content. • SmartFavorites is available only when you connect an SXV200 or later SiriusXM Connect Vehicle Tuner.
SiriusXM® Satellite Radio Selecting items for Content Alert You can select items (artists/songs/teams) from the registered items on the list to inform you once the unit receives the information. • Activate Content Alert by selecting [ON] for [Content Alerts] on the screen beforehand. 1 3 Select [ON] for content you want to receive alerts for. For artists/songs: Display the screen. On the source control screen, touch as follows: E.g.
SiriusXM® Satellite Radio Switching to registered content When receiving the content registered for content alerts, an alert appears on the screen. Touch [Jump], then select the item to jump to on the screen. Traffic & Weather Jump You can standby for receiving traffic and weather information. 1 Setting reception restrictions You can limit access to SiriusXM channels, such as those with mature content.
SiriusXM® Satellite Radio Activating parental control You can set the parental control feature to lock any SiriusXM channels or automatically lock all channels classified as “mature” by SiriusXM®. 1 Display the screen. On the source control screen, touch as follows: Parental Lock channel selection 4 This option allows you to manually select the channels to be locked by the parental control feature. • You can only change the setting if [Parental Control] is set to [User].
SiriusXM® Satellite Radio Skipping unwanted channels 3 Select [ON] for channels you want to skip. If you do not want to receive some channels, you can skip them. 1 You can reset all the SiriusXM® settings you made and restore the initial settings. Display the screen. 1 On the source control screen, touch as follows: Select a category. • Select [OFF] for the channels you do not want to skip.
Pandora® (Only for DDX795/DDX775BH/DDX595/DDX575BT) You can stream Pandora from iPhone/iPod touch or Android devices. • Pandora is only available in certain countries. For more information, visit . • Because Pandora is a third-party service, the specifications are subject to change without prior notice. Accordingly, compatibility may be impaired or some or all of the services may become unavailable. • Some functions of Pandora cannot be operated from this unit.
Pandora® Operation keys on source control screen • The appearance of the operation keys may differ, however the similar operation keys have the same operations. • See also “Common operation keys on source control screen” on page 11. 1 Touching the operation keys performs the following actions: 2 Selecting a station from the list Display the screen. Create a new station 1 On the source control screen, touch as follows: Select a station from the list.
Spotify With Spotify, your music is everywhere. Working out, partying or relaxing, the right music is always at your fingertips. There are millions of songs on Spotify—from old favorites to the latest hits. Just choose the music you love, or let Spotify surprise you. You can stream Spotify from iPhone/iPod touch or Android devices. • Because Spotify is a third-party service, the specifications are subject to change without prior notice.
Spotify Operation keys on source control screen • The appearance of the operation keys may differ, however the similar operation keys have the same operations. • See also “Common operation keys on source control screen” on page 11. Creating your station (Start Radio) Start Radio is to start a radio channel based on the currently played track. Create your station.
Other External Components You can also display the picture from the rear view camera manually without shifting the gear to the reverse (R) position. On the monitor panel: DDX795 DDX775BH DDX6018BT DMX6018BT DDX5018BT To display the front view camera screen (Only for DDX795/DDX775BH/DDX595/DDX575BT/ DDX718WBTL/DMX718WBTL) • Set [Front Camera] to [ON] on the screen beforehand. (Page 54) While the rear camera screen is displayed, touch the area shown below.
Other External Components Watching TV Playback information and key operation (Only for DDX6018BT/DMX6018BT/DDX5018BT/ DDX718WBTL/DMX718WBTL) Using the external navigation unit (Only for DDX6018BT/DMX6018BT/DDX5018BT/ DDX718WBTL/DMX718WBTL) TV You can connect a navigation unit (KNA-G630: optional accessory) to the navigation input terminal so that you can view the navigation screen. (Page 66) • The navigation guidance comes out of the front speakers even when you are listening to an audio source.
Other External Components To exit the navigation screen DDX6018BT DMX6018BT DDX5018BT DDX718WBTL DMX718WBTL Connecting an ADS adapter See page 66 for connection terminals. Using an external component via an ADS adapter • For settings to use an ADS adapter, see on page 50. Switching the screen between the navigation and current source 1 (Only for DMX6018BT/DMX718WBTL) DMX6018BT Display the source/option selection screen.
Bluetooth® Information Bluetooth is a short-range wireless radio communication technology for mobile devices such as mobile phones, portable PCs and other devices. Bluetooth devices can be connected without cables and communicate with each other. Note • While driving, do not perform complicated operations such as dialing numbers, using the phonebook, etc. When you perform these operations, stop your car in a safe place.
Bluetooth® For a Bluetooth device compatible with Bluetooth 2.0: Select the unit (“DDX***” or “DMX***”) on your Bluetooth device. • If a PIN code is required, enter the PIN code shown on the screen (initial: “0000”). To change PIN code, see page 42. 2 4 Determine usage as a hands free device (1), then touch [Close] (2). When your Bluetooth device is compatible with PBAP: Select whether to transfer the phonebook of your Bluetooth device to the unit or not.
Bluetooth® Changing the PIN code 1 Display the screen. On the Home screen, touch as follows: Bluetooth mobile phone Changing the device name of the unit displayed on the paired device 1 When a call comes in... Display the screen. On the Home screen, touch as follows: Then, on the screen, touch [Bluetooth]. On the screen, touch [PIN Code]. 2 Then, on the screen, touch [Bluetooth].
Bluetooth® During a call... 2 1 From the call history* (missed calls/received calls/dialed calls) 2 From the phonebook* 3 From the preset list (Page 44) 4 Use direct number entry 5 Use voice dialing Touching the operation keys performs the following actions: [ ] Ends a call. [ ] Mutes the volume of the microphone. [ [ ]/ ] Switches between hands free mode and phone mode. [DTMF] Enters DTMF (Dual Tone Multi Frequency), then sends text using the keypad.
Bluetooth® C When item 5 is selected in step 2: Say the name of the person you want to call. • You can also make voice dialing by pressing and holding the VOICE on the monitor panel. • Available only when the connected mobile phone has a voice recognition system. • If the unit cannot find the target, “Press [Restart] to restart the voice recognition process.” appears. Touch [Restart], then say the name again. • To cancel voice dialing, touch [Stop].
Bluetooth® Editing phonebook Bluetooth audio player To transfer the phonebook If the connected Bluetooth mobile phone is compatible with Phone Book Access Profile (PBAP), you can transfer the phonebook of the mobile phone to the unit. 1 Bluetooth Display the phone control screen. Playback information and key operation • For playback information, see “Source control screen” on page 10. • For key operations on the touch panel, see “Common operation keys on source control screen” on page 11.
Settings Bluetooth® Bluetooth mobile phone settings You can change various settings for using Bluetooth mobile phones on the screen. 1 Display the screen. On the Home screen, touch as follows: Then, on the screen, touch [Bluetooth]. On the screen, touch [TEL SETUP]. 2 Make the settings. Select the speakers used for Bluetooth mobile phones. • Front: Front speakers only. • All (Initial): All speakers.
Settings Setting the speakers and crossover frequency 1 Select a car type (1), select a speaker (2) (front speakers, rear speakers, or subwoofer) to set, then location and speaker/tweeter size (3) of the selected speaker. A selection window appears for each setting. Select an item, then touch [Close] to close the window. Speaker Select Car Type 3 Select the speaker type (1), then adjust the crossover frequency (2) of the selected speaker.
Settings • To apply the adjusted equalizer to all playback source, touch [ALL SRC], then touch [OK] to confirm. • To clear the adjustment, touch [Initialize]. Store your own sound adjustments 1 2 Select a preset sound mode. Select a band (1) and adjust the level (2), then adjust the sound (3). Graphic Equalizer USB 2 Position/DTA * Not adjustable when is selected for subwoofer on the screen. (Page 47) Preset Select Memory Bass EXT ON Activates/deactivates bass.
Settings [Sound Image LR (Front)] Adjusts the sound image to be localized set on the front position. Localizing the sound image—Front Focus 1 Touch [Front Focus] (1), select the listening position (2) to set as the front position, then touch [Adjust] (3). [Sound Image LR (Rear)] Adjusts the sound image to be localized set on the rear position. Position/DTA Listening Position [Size of the Virtual Sound Field] Adjusts the virtual sound field to the desired field size.
Settings Touch [J]/[K]/[H]/[I] or drag the mark to adjust. Adjusts the front and rear speaker output balance. When using a two-speaker system, set the fader to the center (0). • F15 to R15 (Initial: 0) Adjusts the left and right speaker output balance. • L15 to R15 (Initial: 0) To clear the adjustment: Touch [Center]. Adjust and store the auto-adjustment volume level for each source.
Settings Display settings Display the screen. On the Home screen, touch as follows: You can change the illumination color of the buttons on the monitor panel. Key Color User Scan Then, on the screen, touch [Display]. Adjust • ON: Activates dimmer. • OFF: Deactivates dimmer. • SYNC (Initial): Dims the screen and button illumination when you turn on the headlights. – The ILLUMI lead connection is required.
Settings 3 Rotate the image (1) if necessary, then confirm the selection (2). User interface settings 2 Select a function to assign to the selected button. 3 Repeat steps 1 and 2 to register other functions to other buttons. 4 Touch [Learning completed] to finish procedure. Display the screen. On the Home screen, touch as follows: Then, on the screen, touch [User Interface]. A confirmation message appears. Touch [Enter] to store the new image.
Settings • ON (Initial): Activates the key-touch tone. • OFF: Deactivates the key-touch tone. Adjust the touch positions of the buttons on the screen. Touch and hold the center of the marks at the lower left (1), then the upper right (2) as instructed. Camera settings Display the screen.
Settings Adjust the parking guidelines according to the size of the car, parking space and so on. When adjusting the parking guidelines, make sure to use the parking brake to prevent the car from moving. (Only for DDX795/DDX775BH/DDX595/DDX575BT/ DDX718WBTL/DMX718WBTL) • Lock: Locks the // settings.
Settings Show the Open Source Licenses. Change the PIN code of the unit. (Page 42) (Only for DDX6018BT/DMX6018BT/DDX5018BT/ DDX718WBTL/DMX718WBTL) Clear the security code. (Page 7) Initialize all settings made on the unit. A confirmation message appears. Touch [Yes]. • The settings memorized on the are not initialized. Display the device address of the unit.
Remote Controller • For DDX6018BT/DMX6018BT/DDX5018BT/ DDX718WBTL/DMX718WBTL: This unit can be operated using the remote controller (RC-DV340) supplied with this unit. • For DDX795/DDX775BH/DDX595/DDX575BT: Optional remote controller KNA-RCDV331 is designed for controlling this unit. Refer to the instruction manual that comes with the remote controller. Preparation Battery installation Use two “AAA”/“R03”-size batteries.
Remote Controller Common operations (AUD mode) SRC • Selects the source. • Hangs up the incoming/current call. J/K VOL Adjusts the volume level. ATT Attenuates/restores the sound. DISP/V.SEL • For DDX795/DDX775BH/DDX595 DDX575BT: Switches to the current source control screen. • For DDX6018BT/DMX6018BT/ DDX5018BT/DDX718WBTL/ DMX718WBTL: Switches to the navigation screen. ENTER Enters options. Answers incoming calls. FNC/PBC/ MENU Switches the control screen.
Remote Controller iPod/Android (AUD mode) S/T Selects music/videos. I/W Starts/pauses playback. Basic operations for KNA-RCDV331 (optionally purchased) USB (AUD mode) AM –/FM + Selects a folder. S/T Selects a file. I/W Starts/pauses playback. 1 Press DIRECT to enter the search mode. • Each time you press DIRECT, the item to search for changes. 2 Press a number button to select a desired item (station frequency/chapter/title/ folder/file/track). Confirm the selection.
Remote Controller * +/CLEAR Deletes a character while in direct search mode. # BS/DIRECT Enters direct search mode. J/FM+ / K/AM− Selects a folder. J/FM+ / K/AM− Selects a folder. ROUTE M/ MODE/ TOP MENU Shows the disc top menu. H/S / T / I Selects a track/file. H/S / T/I Selects a file. POSITION/IW Starts/pauses playback. POSITION/IW Starts/pauses playback. VOICE/FNC/ MENU/PBC • Shows the disc menu. • Turns the playback control on or off while playing VCD.
Remote Controller KENWOOD Remote APP KENWOOD Remote is an application that connects and controls compatible KENWOOD car receivers via Bluetooth® like a wireless remote control. You can also operate this unit from a smartphone using KENWOOD Remote APP. This application can display the source information of this unit on the smartphone’s screen, and enables the user to make an audio setting using the graphic user interface of this application.
Installation and Connection • If your car’s ignition does not have an ACC position, connect the ignition wires to a power source that can be turned on and off with the ignition key. If you connect the ignition wire to a power source with a constant voltage supply, such as with battery wires, the battery may be drained. • Only for DDX795/DDX775BH/DDX6018BT/ DDX718WBTL: If the console has a lid, make sure to install the unit so that the monitor panel will not hit the lid when closing and opening.
Installation and Connection Installing the unit (Only for DDX795/DDX6018BT/DMX6018BT/ DDX5018BT/DDX595) Installing the unit using the mounting bracket removed from the car π / “* π /“* 2 Installing the trim plate ] The frame can be removed from the top side in the same manner. Car bracket 3 Note: Select the appropriate screws (supplied) for the mounting bracket. * Only for DDX795/DDX775BH/DDX6018BT/DMX6018BT/ DDX5018BT/DDX595/DDX575BT.
Installation and Connection Wiring connection For DDX795/DDX775BH/DDX6018BT/DMX6018BT/DDX5018BT/DDX595/DDX575BT *1 « *2 *2 Gray/Red ST REMOTE GND Bright green/Red STEERING REMOTE Input 1 Purple/Red [ Connect to your vehicle’s steering remote harness. Contact your KENWOOD dealer for details. Input 2 Connect the antenna cord to the antenna terminal.
Installation and Connection For DDX718WBTL D21 STEERING REMOTE 10 A fuse D22 D23 « Connector D: To the car’s steering remote harness • Depending on the type of vehicle, it cannot be connected. * When using Antenna Control, connect the ANT CONT lead (blue) to A5 (blue) on the wiring harness. [ Connect the antenna cord from the power cord (A) to the antenna terminal.
Installation and Connection For DMX718WBTL D21 STEERING REMOTE 10 A fuse D22 D23 « Connector D: To the car’s steering remote harness • Depending on the type of vehicle, it cannot be connected. * When using Antenna Control, connect the ANT CONT lead (blue) to A5 (blue) on the wiring harness. [ Connect the antenna cord from the power cord (A) to the antenna terminal.
References Installation and Connection Connecting external components AV IN 1 FRONT VIEW CAMERA 1 Expansion port for connecting SiriusXM Connect Vehicle Tuner (EXT I/F) (commercially available)*1 2 Navigation input (NAV)*2 3 Rear view camera input (R-CAM) 4 Video output (V-OUT) 5 Output terminals*3 • Left output (White) • Right output (Red) REAR: Rear speaker preouts FRONT: Front speaker preouts SW: Subwoofer preouts 6 iDatalink input (iDatalink I/F) for connecting an ADS adapter (commercially available)
References • This unit can play back files that meet the conditions below: – Bit Rate: For disc: MP3: 8 kbps – 320 kbps WMA: 5 kbps – 320 kbps AAC: 16 kbps – 320 kbps For USB: MP3/WMA/AAC: 8 kbps – 320 kbps – Sampling Frequency: For disc: MP3/AAC: 32 kHz, 44.1 kHz, 48 kHz WMA: 8 kHz, 11.025 kHz, 16 kHz, 22.05 kHz, 32 kHz, 44.1 kHz, 48 kHz WAV: 44.
References Unplayable disc types and formats • DVD-Audio/DVD-ROM discs • SVCD (Super Video CD), CD Text, CD-ROM, CD-I (CD-I Ready), DTS-CD • JPEG/PNG/BMP/MPEG4/DivX/FLAC/MKV/H.264/ WMV/DVD–VR/DVD+VR/DVD-RAM recorded on DVD–R/–RW or +R/+RW • JPEG/PNG/BMP/MPEG4/DivX/FLAC/MKV/H.264/WMV recorded on CD–R/–RW • DVD–RW dual layer discs • +RW double layer discs • Non-DVD side of a “DualDisc” which does not comply with the “Compact Disc Digital Audio” standard • Discs that are not round.
References About USB playback Important Make sure all important data has been backed up to avoid losing the data. We bear no responsibility for any loss of data stored in the devices while using this unit. Playable files on a USB device • This unit can play the following types of files stored in a USB mass storage class device. – MPEG1/MPEG2/MPEG4/H.264/WMV/MKV/MP3/ WMA/WAV/AAC (.
Troubleshooting What appears to be trouble is not always serious. Check the following points before calling a service center. • For operations with external components, refer also to the instructions supplied with the adapters used for connection (as well as the instructions supplied with the external components). “Learning Process Failed” appears. A Your steering remote controller is not compatible, learning may not be completed. Consult your car audio dealer for details.
Troubleshooting iPod/iPhone HD Radio AV-IN No sound comes out of the speakers. A Disconnect the iPod/iPhone, then connect it again. A Select another source, then reselect “iPod”. (Only for DDX795/DDX775BH) AME automatic presetting does not work. A Store stations manually. (Page 21) (Only for DDX6018BT/DMX6018BT/DDX5018BT/ DDX718WBTL/DMX718WBTL) The iPod/iPhone does not turn on or does not work. A Check the connection. A Update the firmware version. A Charge the battery. A Reset the iPod/iPhone.
Troubleshooting “Cannot create a Station” appears. A You cannot create a station during the readonly mode or when network connection is not established. “Unable to save your bookmark” appears. A The unit has failed to save a bookmark. Try the operation again. “Pandora is undergoing maintenance. Please try again later” appears. A An error has occurred on the Pandora application. “Station does not exist” appears. A The selected station has been deleted by another device or has expired.
Specifications Troubleshooting Bluetooth Phone sound quality is poor. A Reduce the distance between the unit and the Bluetooth mobile phone. A Move the car to a place where you can get a better signal reception. The sound is interrupted or skipped while using a Bluetooth audio player. A Reduce the distance between the unit and the Bluetooth audio player. Disconnect the device connected for Bluetooth phone. A Turn off, then turn on the unit. (When the sound is not yet restored) connect the player again.
Specifications DVD player section (Only for DDX795/DDX775BH/DDX6018BT/ DDX5018BT/DDX595/DDX575BT/DDX718WBTL) D/A Converter 24 bit Audio Decoder Linear PCM/Dolby Audio/MP3/ WMA/WAV/AAC (.m4a) Video Decoder MPEG1/MPEG2 Wow & Flutter Below Measurable Limit Frequency Response 96 kHz Sampling: 20 Hz to 20 000 Hz 48 kHz Sampling: 20 Hz to 20 000 Hz 44.1 kHz Sampling: 20 Hz to 20 000 Hz Total Harmonic Distortion 0.
Specifications FM tuner section Frequency Range AM tuner section DDX795/DDX775BH/DDX595/ DDX575BT: 87.9 MHz to 107.9 MHz (200 kHz) Frequency Range 530 kHz to 1 700 kHz (10 kHz) Usable Sensitivity 29 dBμ Frequency Response (±3.0 dB) DDX6018BT/DMX6018BT/ DDX5018BT/DDX718WBTL/ DMX718WBTL: 87.5 MHz to 108.0 MHz (50 kHz) Signal to Noise Ratio Usable Sensitivity (S/N: 30 dB, Dev. 22.5 kHz) 7.2 dBf (0.63 μV/75 Ω) Color System of External Video Input NTSC/PAL Quieting Sensitivity (DIN S/N: 46 dB, Dev.
Specifications 2 Way X'Over Tweeter: Front/Rear (HPF): Subwoofer (LPF): Position General Gain (dB): –8/–7/–6/–5/–4/–3/–2/–1/0 Frequency (Hz): Through/30/40/50/60/70/ 80/90/100/120/150/180/ 220/250 Slope (dB/Oct.): −6/−12/−18/−24 Gain (dB): –8/–7/–6/–5/–4/–3/–2/–1/0 Frequency (Hz): 30/40/50/60/70/80/90/100/ 120/150/180/220/250/ Through Slope (dB/Oct.
Specifications Trademarks and licenses • Dolby, Dolby Audio and the double-D symbol are trademarks of Dolby Laboratories. • “DVD Logo” is a trademark of DVD Format/Logo Licensing Corporation registered in the US, Japan and other countries. • The “AAC” logo is a trademark of Dolby Laboratories. • Microsoft and Windows Media are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.
For updated information (the latest Instruction Manual, system updates, new functions, etc.), please visit the following website:
MILITARY Units purchased through the U.S.A. military exchange service overseas may be serviced under warranty in the continental U.SA. subject to the following conditions. 1) The original warranty is in effect. 2) Proof of purchase is provided to the servicer. WARRANTY FOR MILITARY MARKET JVC KENWOOD corporatiOn 1s proud of the quafily and workmanship of itsaudi oequipment. This unit has beenproperJy designed, tested and inspected before it was shipped to you.
U .S.A. JVCKENWOOD USA Corporation This warranty wilt be honored only in the U.S.A. KENWOOD LIMITED WARRANTY FOR CAR STEREO COMPONENTS EXCLUSION OF DAMAGES KENWOOD WARRANTY This warranty is enforceable only by the original purchaser. KENWOOD'S LIABILITY FOR ANY DEFECTIVE PRODUCT IS LIMITEDTO THEREPAIRORREPLACEMENTOFTHEPRODUCT AT OUR OPTION. KENWOOD SHALL NOT BE LIABLEFOR: 1. INSTALLATION OR REMOVAL CHARGES. DAMAGE TO OTHER PROPERTY CAUSED BY ANY DEFECTS IN KENWOOD CAR STEREO COMPONENTS.
