GPS NAVIGATION SYSTEM DNX8220BT DDX8022BT MONITOR WITH DVD RECEIVER INSTRUCTION MANUAL Declaration of Conformity with regard to the R&TTE Directive 1999/5/EC Manufacturer: Kenwood Corporation 2967-3 Ishikawa-machi, Hachioji-shi, Tokyo, 192-8525 Japan EU Representative's: Kenwood Electronics Europe BV Amsterdamseweg 37, 1422 AC UITHOORN, The Netherlands © B64-4093-00/00 (EW/E2W) B64-4093-00̲00̲EN.indb 1 08.2.
Contents How to read this manual Before Use Notes Navigation Control 4 6 7 14 Using the Navigation System 14 Control of Other Sources While Displaying the Navigation Screen 14 Accessing the SD Memory Card Insertion Slot (DNX8220BT only) 16 Watching DVD/VCD & DVD Audio Listening 18 Functions During the Playback Screen 18 Functions When Displaying the Easy Control Panel 19 Functions While Displaying the Control Screen 20 DVD Disc Menu 21 VCD Zoom Control 22 Music Disc & Audio File Listening Functions
Hands Free Unit Control 50 Before Use 50 Downloading the Phonebook 50 Control Screen Function 50 When Received a Call 51 Calling by Entering a Phone Number 52 Quick Dialing 52 Controlling tone-based services 53 Calling by Phonebook 53 Making a Call Using Outgoing/Incoming Call Records 55 Calling by Voice Recognition 55 Setting Up the Hands Free Phone 56 Voice Registration 57 Key Word Voice Registration 58 Phone Number Preset 59 SMS (Short Message Service) 60 Setup Menu Setup Menu Audio Setup Speaker Set
How to read this manual This manual uses illustrations to explain its operations. Seek Mode The displays and panels shown in this manual are examples used to provide clear explanations of the operations. For this reason, they may be different from the actual displays or panels used, or some display patterns may be different. Sets a station selection. The mode is switched in following order each time you touch the button.
English B64-4093-00̲00̲EN.indb 5 5 08.2.
Before Use 2WARNING Handling discs To prevent injury or fire, take the following precautions: • Do not touch the recording surface of the disc. • Do not stick tape etc. on the disc, or use a disc with tape stuck on it. • Do not use disc type accessories. • Clean from the center of the disc and move outward. • When removing discs from this unit, pull them out horizontally. • If the disc center hole or outside rim has burrs, use the disc only after removing the burrs with a ballpoint pen etc.
Notes Navigation units that can be connected to this unit (DDX8022BT only) • • • • • * KNA-G520* KNA-G420* KNA-G421* KNA-DV3200 KNA-DV2200 Update the navigation software to the latest version. For how to update the software, refer to the instruction manual of the navigation unit.
Notes About Audio files • Playable Audio file AAC-LC (.m4a), MP3 (.mp3), WMA (.wma) ⁄ • If music of normal CD and other playback systems are recorded in the same disc, only the playback system recorded at the first setout is played. • Playable disc media CD-R/RW/ROM, DVD±R/RW • Playable disc file format ISO 9660 Level 1/2, Joliet, Romeo, Long file name.
Region codes in the world The DVD players are given a region code according to the country or area it is marketed, as shown in the following map. 1 5 2 6 1 2 3 1 4 5 2 4 DVD disc marks Operation regulatory marks Symbol With this DVD, some functions of this unit such as the play function may be restricted depending on the location where the DVD is playing. In this case, the following marks will appear on the screen. For more information, refer to the disc manual.
Basic Operations E D C B A C B Turns power ON/OFF Switches to the Navigation system Press the button to turn on the power. When the button is pressed and held down for 1 second or more, the power is turned off. Press the button to switch the display to the navigation system screen. E D Attenuates the volume Adjusts the volume Press it to attenuate the volume. Press it again to cancel muting. Playing a USB device When connecting a USB device, playback starts automatically.
C Selecting a source Press it to display the source select screen. Touch the source button to select the source. Full Source Select screen 5 6 7 1 2 8 3 9 4 10 1 11 11 1 Scrolls the source display. 2 Displays the external device control screen. See (page 46). 3 Changes the screen skin each time it is pressed. 4 Displays the Hands Free screen. (page 50) 5 Press for at least 2 seconds to erase the buttons. Touch the screen to redisplay the buttons.
Basic Operations C B A B A Switches to the Hands Free control Switches to the rear view Press it for more than 1 second to the Hands Free control screen. Press it again for more than 1 second to resume the normal display. (with the optional accessory Bluetooth unit connected only) Press it for more than 1 second to switch to rear view. Press it again for more than 1 second to resume the normal display. C ⁄ • Functions of the [NAV] button can be changed to Display Off function.
B Switching the function screen The function control screen switches in the following order each time you press the button. Picture or Video playback screen Navigation screen [FNC] button [FNC] button Easy Control buttons appear. Easy Control buttons appear.
Navigation Control Sets and controls the navigation system function. Using the Navigation System Displays the navigation system screen and makes the navigation function available. 1 Displaying the navigation screen Control of Other Sources While Displaying the Navigation Screen Selected source can be controlled while displaying navigation screen.
time. (DVD play only) 5 Plays or pauses. 6 When touched this area, the source control screen appears. When "USB" or "iPod" is selected: 7 8 7 iPod 9 P 0:00:05 IN 7 During iPod play : Searches Music or Video. During USB play : Selects a file. 8 Plays or pauses. 9 When touched this area, the source control screen appears. When "TUNER" is selected: 10 10 12 TUNER 11 AM FM 11 FM1 98.1 MHz IN p Tunes in a station. q Switches the band (to AM or FM 1/2/3).
Navigation Control Accessing the SD Memory Card Insertion Slot (DNX8220BT only) An SD memory card is used to upgrade the map. 1 Press [SRC] to turn the power on 2 Press [0] to close the panel 3 Press [0] for at least 1 second to fully open the panel ⁄ • See the NAVIGATION SYSTEM's INSTRUCTION MANUAL for the detail upgrade method. 16 DNX8220BT/DDX8022BT B64-4093-00̲00̲EN.indb 16 08.2.
English B64-4093-00̲00̲EN.indb 17 17 08.2.
Watching DVD/VCD & DVD Audio Listening You can play DVD/VCD using various functions. • For the basic method of how to watch DVD/VCD, refer to (page 10). • Set the remote controller mode switch to "DVD" mode before starting operation, refer to (page 94). Functions During the Playback Screen Basic functions are available even when the playback screen is displayed.
Selects the next scene (when PBC is On) or track (when PBC is Off ). i Backward Scene/Track Search Area Selects the previous scene (when PBC is On) or track (when PBC is Off ). o Zoom Control Button Area Displays the Zoom Control buttons (page 22). ; Information Display Button Area Turn off the information when it is displayed. Functions When Displaying the Easy Control Panel Displays the basic operation buttons on the screen.
Watching DVD/VCD & DVD Audio Listening Functions While Displaying the Control Screen Switches to the source control screen to use various playback functions.
DVD Disc Menu Highlight Control You can select a chapter and title for the DVD Menu screen. When you touch the screen, you can select the DVD menu. Selects an option from the DVD Disc Menu.
Watching DVD/VCD & DVD Audio Listening 9 Calls the Menu Control. p Switches the picture angle. (during program playback only) q Switches the subtitle language. (during program playback only) w Switches the voice language. (during program playback only) e Displays the Zoom Control screen. r Selects a picture. (during DVD Audio play only) t Clears the Disc Menu Control. SUB Displays an enlarged VCD screen.
Music Disc & Audio File Listening You can recall various control screens during CD/Audio file playback. • For the basic method of how to play a music disc/audio file, refer to (page 10). • Refer to (page 7) for playable discs. • Refer to (page 8) for playable files. Functions While Displaying the Control Screen Switches to the source control screen to use various playback functions.
Music Disc & Audio File Listening During Audio file playback 2 4 3 5 1 6 6 8 9 10 12 7 11 14 13 18 25 8 15 11 16 17 19 20 ; Appears when a disc is inserted. a Repeats to play the music or data of the present folder. s You can search for folders and Audio files through a hierarchy. d Displays music information (such as Tag and content property) of Audio file being played. f Displays the external device control screen. See (page 46).
Set Disc Name Folder Select (Function of Audio File) Assigns a name to a CD. Searches folders and Audio files stored in media and devices according to hierarchy. 1 Play a CD you wish to name 1 Start Folder Select 2 Start Name set 2 Selects a song 3 Enter the name See (page 48) for information on how to enter a name. 2 3 1 4 End Name set 4 2 5 6 1 Lists folders and Audio files Folder opens when touched, and the Audio file is played.
Video File/Picture Watching You can recall various control screens during playback of video file (MPEG 1 and MPEG 2 and DivX file) and picture file (JPEG file). Function During Playback Screen 6 Information Display Button Area Turn off the information when it is displayed. Basic functions are available even when the playback screen is displayed. ⁄ 1 Display the playback screen • The information display is cleared automatically after approximately 5 seconds.
Functions While Displaying the Control Screen Switches to the source control screen to use various playback functions. 1 While the source is playing, press the [FNC] button Mode:Full DVD MEDIA O 7 8 9 p q w e AV–OUT:AV–IN r t O SCRN 6 y 2 DVD MEDIA P 1 PICTURE 2 0:00:05 IN 3 4 1 5 6 8 6 7 8 9 10 12 13 11 14 18 11 17 16 15 u i o ; a s 19 20 d f When is appeared, the text display is scrolled by pressing it. Fast Forwards or Fast Backwards.
Video File/Picture File Watching Picture Control Folder Select Adjusting the video display. Searches folders and Video files/Pictures stored in media and devices according to hierarchy. 1 Start Picture Control 1 Start Folder Select DVD MEDIA DVD MEDIA Mode:Full 2 AV–OUT:AV–IN P 1 0:00:05 IN 2 Adjust the video display 2 Selects a file Picture Ctrl 2 3 2 3 1 4 1 1 2 3 4 28 Reverses the picture horizontally. Rotates counter clockwise. Rotates clockwise. Ends Picture Control.
Radio Listening Various control screens appear in the Tuner Source mode. • For the basic method of receiver button operations, refer to (page 10). • Set the remote controller mode switch to "AUD" mode before starting operation, refer to (page 94). Functions While Displaying the Control Screen Switches to the source control screen to use various functions. 3 2 1 4 5 6 8 8 7 9 10 11 12 13 14 15 16 17 1 2 3 4 18 19 Text.
Radio Listening Seek Mode Auto Memory Sets a station selection. Stores stations with good reception in memory automatically. 1 Select a band you wish to store in memory The mode is switched in following order each time you touch the button. Display "AUTO1" "AUTO2" "MANU" Setting Tunes in a station with good reception automatically. Tunes in stations in memory one after another. Switches to the next frequency manually. 2 Select the Auto Memory mode 3 Start Auto Memory Touch or .
# : Press for # seconds. Manual Memory Preset Select Stores the current receiving station in memory. Lists and selects memorized station. 1 Select a station you wish to store in memory 2 Store in memory 1 Start Preset Select 2 Selects a station 2 1 1 3 Continue to touch until the memory number appears. 1 Scrolls the list. 2 Memorized stations are displayed. Touch to tune in. 3 Returns to the original screen. English B64-4093-00̲00̲EN.indb 31 31 08.2.
Radio Listening Radio Text Traffic Information You can display the radio text. (Only when receiving the FM broadcast) When a traffic bulletin starts, any source is switched to the traffic information and it is displayed automatically. 1 Select a station 1 Set the Traffice information mode 2 Display the radio text When the traffic bulletin starts... The Traffic Information screen appears automatically.
Search for Program Type A program is tuned when you set its program type. (Only when receiving the FM broadcast) 1 Enter Program Type mode 2 Select a Program Type 1 2 2 1 Program Type is displayed. Touch to select a Program Type. 2 Scrolls the Program Type list. 3 Search a station of the selected Program Type English B64-4093-00̲00̲EN.indb 33 33 08.2.
iPod Control You can control and listen to songs in your iPod by connecting an iPod to this unit with KCA-iP300V (optional accessory). You can also display video contents on this unit when connecting an iPod with video. Functions when Displaying the Easy Control Panel Connecting an iPod Connect an iPod to this unit. Displays the basic operation buttons on the screen.
Functions while Displaying the Control Screen Switches to the source control screen to use various playback functions. 17 When Video or picture is playing, press the [FNC] button. Mode:Full iPod AV–OUT:AV–IN O iPod P 0:00:05 IN or 2 4 3 1 5 9 10 6 11 8 7 12 19 20 1 Image picture Switches to the playback screen. If there is no playback screen, wallpaper is displalyed.
iPod Control iPod List Lists and searches music/video contained in the iPod. 1 Display the iPod List 2 Select music/video 2 1 3 4 5 1 6 1 Switches list page. 2 Categories and music are listed. Touch a category name to move its lower level. If music title is displayed, the music is played by touching it. When is appeared, the text display is scrolled by pressing it. 3 All the music in its category is played. 4 Returns to previous category. 5 Moves to the top category.
English B64-4093-00̲00̲EN.indb 37 37 08.2.
USB Device Control You can control and listen to songs in your USB device by simply connecting it to the USB connector of this unit. • For the connection of a USB device, refer to (page 10). Functions while displaying the Control Screen 5 Removes the USB device. When "No Device" is shown, the USB device can be removed safely. If you wish to play it again while the USB device is connected, press it again. 6 Selects a folder. (Only in Folder Select Mode)* 7 Selects a file.
USB List Folder Select Lists and searches music contained in the USB device. Searches folders and Audio files stored in the USB device according to hierarchy. 1 Display the Category List 1 Start Folder Select 2 Select a category 2 Select music 1 2 3 4 2 1 5 2 When is appeared, the text display is scrolled by pressing it. 1 Displays the currently playing category. 2 Returns to the original screen.
TV Watching Various control screens appear in the TV source mode. You can only operate TV with the optional accessory TV Tuner connected. Function During TV Screen Basic functions are available even when the TV screen is displayed. 1 Display the TV screen Functions When Displaying the Easy Control Panel Displays the basic operation buttons on the screen.
Functions While Displaying the Control Screen Switches to source control screen to use various functions. 1 While the source is playing, press the [FNC] button 8 9 p q w e r Mode:Full TV t y u O SCRN O AV–OUT:AV–IN BAND TV 2 SEEK 2ch Preset 1 TV1 3 4 Use the (page 42) to change the channel tuning sequence. Switches to TV1 or TV2. Switches the button display. Selects the Auto Memory mode. See (page 43). Switches the Seek mode. See (page 42).
TV Watching TV Menu (with KTC-D500E (optional accessory) connected only) Seek Mode Sets a station selection. Menu Control screen appears by touching the area shown below. Mode:Full TV TV TV1 G ro u p 1 Preset 1 IN AUTO1 1 Me n u Ctrl 6 EPG 4 6 En t e r 42 2ch AF 2 3 Menu Return 6 6 1 2 3 4 5 6 AV–OUT:AV–IN The mode is switched in following order each time you touch the button. Display "AUTO1" "AUTO2" "MANU" Setting Tunes in a station with good reception automatically.
# : Press for # seconds. Auto Memory Manual Memory Stores stations with good reception in memory automatically. Stores the current receiving channel in memory. 1 Select a band you wish to store in memory 1 Select a station you wish to store in memory 2 Select the Auto Memory mode 2 Store in memory 3 Start Auto Memory Continue to touch until the memory number appears. Auto Memory terminates when 6 stations are stored or when all stations are tuned in.
TV Watching Preset Select Set Station Name Lists and selects memorized station. Assigns a name to a station. 1 Start Preset Select 1 Select a station you wish to name 2 Start Name set 2 Selects a station 3 Enter the name 1 See (page 48) for information on how to enter a name. 4 End Name set 1 Memorized stations are displayed. Touch to tune in. 44 DNX8220BT/DDX8022BT B64-4093-00̲00̲EN.indb 44 08.2.
Bluetooth Audio Control You can listen to audio files stored in Bluetooth audio player and cell-phone. Before Use • You need to register your audio player and cell-phone before using it with this unit. For more details, see (page 82). • If you have registered two or more audio players or cellphones, you need to select one of them. For more details, see (page 84).
External Device Power Supply Control Controlling the external device power supply. External Device Power Supply Control Controlling the external device power supply. 1 Displays the EXT SW Control screen [EXT SW] appears when the control screen of each source or Easy control panel is displayed. 2 Controls the external device power supply 1 1 2 1 You can turn on or off the external device power supply. 2 Returns to the original screen.
Muting Audio Volume upon Reception of Phone call When the telephone is called, the system is paused automatically. Muting Audio Volume upon Reception of Phone Call When the telephone is called... The Phone Call ("CALL") screen appears, and system is paused. Phone Call ("CALL") screen When the call ends... Hang up the phone. The system resumes playing automatically. ⁄ • To use the TEL Mute feature, you need to hook up the MUTE wire to your telephone using a commercial telephone accessory.
Character Entry When you select the Set Station Name mode or others, the following screen appears for character entry. How To Use the Character Entry Screen Character Entry screen 1 1 2 3 3 4 5 6 7 1 Shifts the cursor. 2 Enters characters. 3 Scrolls up or down the character button display. 4 Sets the key layout of the character buttons. ABC : Alphabetical key layout. QWE : Qwerty key layout. 5 Enters a space. If you erase a character, locate the cursor on it and touch this button.
Screen Control Setting the monitor screen. Screen Control Day/Night display setting. 7 Returns to the previous screen. ⁄ 1 Display Easy Control panel • The Screen Control screen is displayed only when you have applied the parking brake. • The picture quality can be set for each source. • You can set image quality of screens such as menu from (page 77) of the .
Hands Free Unit Control Various functions can be used in the Hands Free control mode. Before Use Control Screen Function • To use the Phonebook, it must be downloaded to this unit in advance. For details, see (page 50). • You need to register your cell-phone before using it with this unit. For more details, see (page 82). • If you have registered two or more cell-phones, you need to select one of them.
2 3 4 5 6 7 8 9 p q w : Indicates there is a call on hold. : Displays the signal strength.* The more the number of bar segments, the stronger the signal. : Displays the present Auto Answering status : When Auto Answering is on : When Auto Answering is off : Displays the battery drain of the cellphone.* The more the number of bar segments, the higher the battery level. Displays the called phone numbers. If you have registered a phone number in the Phonebook, the destination person name is displayed.
Hands Free Unit Control Calling by Entering a Phone Number Quick Dialing Make a call by entering a phone number. You can register up to 6 phone numbers for quick dialing. 1 Display the number input screen ⁄ • Phone numbers must be registered in advance. See (page 59). 1 Recall the phone number 2 Enter a phone number 1 2 Make a call 2 3 4 1 Calls the entered phone number. 2 Creates an SMS for the entered phone number. See (page 60).
Controlling tone-based services Calling by Phonebook Uses tone base service using DTMF (Dual Tone Multi Frequency). You can call a person using his/her phone number that you have registered in the Phonebook. 1 Display the DTMF input screen Display the Talking screen. See (page 52). 1 Display the Phonebook screen The Initial Input screen appears.
Hands Free Unit Control r Calls the selected phone number. t Creates an SMS for the displayed phone number. See (page 60). y Scrolls the phone number. u Returns to the Name List screen. i Returns to the Hands Free Control screen. Cyrillic alphabet search screen 5 А 2 О 2 3 5 Make a call 5 Displays the Phonebook beginning with the name whose first character you have touched.
Making a Call Using Outgoing/Incoming Call Records Calling by Voice Recognition Calls by selecting a phone number from the outgoing or incoming calls list. ⁄ 1 Display the Outgoing Calls or Incoming Calls screen Calls by recognizing the registered voice. • In order to perform voice recognition, voice must be registered in the Phonebook data. See (page 57). Or, to perform voice recognition by Phone number category (Home, Office, Mobile etc.
Hands Free Unit Control If you hear another Beep sound: Speak the key word within 2 seconds after the Beep, or touch the [Phonebook List] button to select the phone number. Setting Up the Hands Free Phone The Hands Free system can be set as follows. 1 Display the Hands Free Setup screen Make a call. ⁄ • If there are more than one phone numbers registered under the same name, and the key word voice is registered for each phone number, you will hear another beep.
6 7 8 9 p q w "On": Beep is heard. "Off": Beep is canceled. Returns to the "Hands Free Control" screen. Returns to the "Hands Free Setup 1" screen. Sets whether to use cell-phone phonebook, outgoing calls list and incoming calls list. ( "On") "On": Yes. "Off": No. Sets the SMS function. ( "On") "On": Use SMS function. "Off": SMS not available. Registers the voice to select phone number category with voice recognition. See (page 58).
Hands Free Unit Control 5 End voice registration Key Word Voice Registration Registers the voice to select the Phone number category by Voice Recognition. 1 Display the Key Word List screen Display the "Hands Free" screen and touch [Setup]. See (page 50). ⁄ • A message is displayed if the voice is not recognized. Read the message for the further operation. • Repeat from 1st try if the voice is different from the 1st try.
4 Utter the voice to register (1st try) Phone Number Preset Registers frequently used phone number to Hands Free control screen preset button. 7 1 Display the Hands Free Preset List screen 6 Display the "Hands Free" screen and touch [Setup]. See (page 50) 6 Registers the voice. 7 Cancels voice registration. Utter within 2 seconds after the Beep.
Hands Free Unit Control 9 Registers the currently displayed phone number. p Deletes the currently displayed phone number. q Returns to the previous screen. SMS (Short Message Service) Uses SMS function. 1 Display the SMS Select screen 4 Search phone number to register with each function 5 Register phone number 2 Select a function 1 2 ⁄ 3 • Press [Delete] to delete the registered phone number. 4 5 1 Displays received message list. 2 Displays sent message list. 3 Displays the Message screen.
SMS Message screen 10 11 12 13 12 p Calls the number in the selected message. q Creates a new message for the selected message. w Scrolls the message. e Returns to the previous screen. 4 Create a message 14 15 14 17 17 18 16 19 20 21 22 r Moves the cursor. t Displays remaining number of characters allowed. y Enters character. u Changes keyboard character type. i Sends the message. o Sets the key layout of the character buttons. ABC : Alphabetical key layout. QWE : Qwerty key layout.
Setup Menu You can setup various receiver parameters. Setup Menu Audio Setup Displays the Setup menu to set various functions. You can set up the car type and speaker system you use together with this unit. 1 Display the control screen of any source 1 Display the Audio Setup screen Touch Menu" screen (page 62). in the "SETUP ⁄ Touch any source button on the "Source Select" screen.
Speaker Set Up When the speaker type and size are set, the speaker crossover network and equalizer curve are set automatically. You can select a speaker type and its size to get the best sound effects. 1 Select a speaker you wish to adjust 1 5 10 9 6 7 2 2 3 3 5 7 8 4 11 5 Selects a speaker to be set. (see , page 63) 6 Sets the use or no use of tweeter. (see , page 63) 7 Selects a speaker type.
Setup Menu Subwoofer: NONE, 16cm, 20cm, 25cm, 30cm, 38cm over ⁄ • Select "NONE" if you have no speakers. • If you set the center speaker to "NONE" even in a short time when you are setting the Surround Control (page 91) to "Bypass+Center", the Surround Control is set to "Bypass" automatically. • If you set the center and rear speakers to "NONE" when you are setting the Surround Control (page 91) to "Dolby PL II", the Surround Control is set to "Bypass" automatically.
DTA Setup You can manually set the sound output timing of each channel. 1 Display the DTA Setup screen When the values of center speaker and front speakers increase, they are virtually moved forward. When the values of rear speakers and subwoofer increase, they are virtually moved backward. 1 2 2 3 1 Selects a speaker to be adjusted. 2 Sets a delay time of the selected speaker. 3 Returns to the Car Type Set Up screen.
Setup Menu Crossover Network Setup on the Speaker Set Up screen. You can set a crossover frequency of speakers. 1 Select the speaker to set the crossover 1 2 2 3 3 5 4 6 1 Sets the High Pass Filter of the center speaker. 2 Sets the High Pass Filter of the front speaker. 3 Sets the High Pass Filter of the rear speaker. 4 Sets the Low Pass Filter of the sub woofer. 5 Switches to the crossover setup screen. 6 Returns to the "SETUP Menu" screen.
DVD Setup 7 8 9 You can setup the DVD play. 10 1 Display the DVD SETUP screen Touch Menu" screen (page 62). 11 in the "SETUP 12 13 2 Setup each item 7 8 9 p Returns to the "DVD SETUP 1" screen. Moves to the "DVD SETUP 3" screen. Sets an angle mark display. ( "On") Selects the screen display mode.*1 ( "16:9") "16:9": Displays wide pictures. "4:3 LB": Displays wide pictures in the Letter Box format (having black stripes at the top and bottom of screen).
Setup Menu Language Setup 18 19 Selects a language you use for the speech and menus. 20 1 Select the language item to set 21 i Returns to the "DVD SETUP 3" screen. o Switches Group Continuous On or Off. ( "Off") If "Off" is selected, the group playback is stopped or menu screen is appeared at the end of the group playback. If "On" is selected, the group playback is continued. ; Switches the Video Mode of a DVD Audio disc On or Off.
Parental Level Setup 4 Select a parental level and complete the setup Sets a parental level. 1 Display the Parental Level code number screen See to (page 67) and touch [Parental Level]. 6 6 7 6 Selects a parental level. 7 Complete the parental level setup and returns to the "DVD SETUP 2" screen. ⁄ 2 Enter the code number 2 1 • If a disc has higher parental lock level, you need to enter the code number. • The parental lock level varies depending on a loaded disc.
Setup Menu System Setup 7 8 You can setup the system parameters. 9 1 Display the SETUP System screen Touch Menu" screen (page 62). in the "SETUP 10 2 Setup each item 7 Returns to the "System SETUP 1" screen. 8 Sets the function of the [NAV] button. "V. OFF: Press the [NAV] button for more than 1 second to turn the display off. "R. CAM": Press the [NAV] button for more than 1 second to switch to rear view. 9 Sets whether using DSP function or not when playing DVD-Audio.
AV Interface Setup 7 You can set audio and visual (AV) interface parameters. 8 9 10 11 1 Display the AV Interface screen Touch Menu" screen (page 62). in the "SETUP 2 Setup each item 1 2 3 4 5 6 1 Moves to the "AV Interface 2" screen. 2 Sets a name to be displayed when you select a system that is connected via the AV INPUT1 port. ( "VIDEO1") 3 Sets an image display of the system that is connected via the AV INPUT2 port.
Setup Menu y Mutes the volume during voice guidance of the navigation system. ( "On") When turned "On", the volume level drops for voice guidance. u Sets the voice guidance method of the Navigation system. ( "On") (DNX8220BT only) "On" : Voice guidance is On. "Off" : Voice guidance is Off. i Returns to the "SETUP Menu" screen. User Interface You can setup user interface parameters. 1 Display the User Interface screen Touch Menu" screen (page 62).
8 7 9 10 11 12 13 7 Returns to the "User Interface 1" screen. 8 Moves to the "User Interface 3" screen. 9 Sets an on-screen display of the iPod Playback screen. ( "Auto") "Auto": Information is displayed for 5 seconds when updated. "Manual": Information is displayed when you touch on the screen. p Sets an on-screen display of the navigation screen. ( "Off") "Auto": Information is displayed for 5 seconds when updated. "Off": Information is not displayed.
Setup Menu Direct Source Button Setup Entering Background Registers the source displayed in the favorite source screen. Loads a image for background. 1 Connect the device which has the image to load 1 Displays the Direct SRC button Setup screen 2 Display the User Interface screen Touch Menu" screen (page 62). in the "SETUP 3 Display the Background Memory screen See (page 72).
Background Delete Background Select Deletes the background image. Selects a image for background. 1 Display Delete Image Select screen 1 Select Background Change screen 2 Select the image to be deleted 2 Select a image for background 1 2 1 1 Returns to the initial background. 2 Returns to the original screen. 1 Returns to the original screen. 3 Delete the image 3 Set the image as the background 4 Confirm 2 2 Returns to the Pictrue Select screen. English B64-4093-00̲00̲EN.indb 75 75 08.2.
Setup Menu Touch Panel Adjustment Clock Setup You can adjust the touch panel operations. You can adjust the clock time. 1 Display the Touch panel Adjustment screen Touch Menu" screen (page 62). in the "SETUP 1 Display the Clock Setup screen Touch Menu" screen (page 62). in the "SETUP 2 Setup the Clock 2 Start Touch panel setup 2 3 2 3 1 4 5 6 1 1 Returns to the "SETUP Menu" screen. 3 Adjust the Touch panel 2 3 Follow the instruction on the screen and touch the center of .
Monitor Setup You can adjust the position, picture quality and the screen mode of the monitor. p Stores the current monitor angle as the angle during power off. q Returns to the "SETUP Menu" screen. 1 Displaying the Monitor SETUP screen Touch Menu" screen (page 62). in the "SETUP 12 13 14 15 2 Setup each item 16 1 17 2 18 3 4 6 5 1 2 3 4 5 Moves to "Tilt Control" screen. Brightness control Contrast Control Black Level Adjustment Dimmer Mode Setup "ON": The display dims.
Setup Menu "Full", "Just", "Zoom", "Normal" ; Returns to the "Mode Select 1" screen. a Selects a screen mode of the rear view camera (R-CAM) screen. You can select any of the following screen mode. "Full", "Just", "Zoom", "Normal" s Returns to the "SETUP Menu" screen. ⁄ • When you select the Menu or Navigation, the display is shown in the full-size display mode automatically. The screen mode of these displays cannot be changed. • The picture qua¡lity can be set for each source.
4 Register your security code If you have pressed the Reset button or if you have disconnected the Receiver from battery... 1 Enter the correct security code 5 Reenter the security code Reenter the same security code as that you have entered in Step 3 for confirmation. ⁄ • If you enter a different security code, the screen returns to Step 3 (for the first code entry). You must enter the same security code as that you have entered in Step 3.
Setup Menu TV Setup RDS Setup The TV signal receiving areas can be set. (with the optional accessory TV Tuner connected only) You can set RDS related parameters. 1 Display the RDS Setup screen 1 Displaying TV SETUP screen Touch Menu" screen (page 62). in the "SETUP Touch Menu" screen (page 62). in the "SETUP 2 Setup each item 2 Setting up TV 1 1 2 3 4 5 2 6 3 1 Moves to "TV2 Area Set" screen. 2 Sets the present TV1 receiving area. 3 Returns to the "SETUP Menu" screen.
iPod Setup Bluetooth Setup Performs setup when using iPod. Registers and selects Bluetooth unit. 1 Display the Bluetooth Setup screen 1 Display the iPod SETUP screen Touch Menu" screen (page 62). in the "SETUP Touch Menu" screen (page 62). in the "SETUP 2 Setup each item 2 Setup each item 1 1 2 2 3 1 Sets the Audio book playback speed. 2 Sets Wide Screen on or off. 3 Returns to the "SETUP Menu" screen. ⁄ 3 1 Sets cell-phone for Hands Free and Audio player for Bluetooth Audio.
Setup Menu Registering Bluetooth Unit 4 Enter PIN code Registers the Bluetooth unit to be connected. Enter the PIN code specified for the Bluetooth unit to register. 1 Display the Connect Device List screen 13 12 14 15 w e r t 2 Search for a Bluetooth unit 1 2 3 Enters a code number. Cancels registration of PIN code. Enters PIN code. Clears the code number. ⁄ 4 5 1 Displays the registered Bluetooth unit. Displays the busy service in blue. Displays the available service in gray.
Registering Bluetooth Unit PIN Code Registering Special Bluetooth Unit Sets the PIN code of the Bluetooth unit to enter when registering (pairing) from the cell-phone or audio player side. Registers Special Bluetooth unit that results in error by normal operation by selecting from model name. 1 Display the Receiver PIN Code screen 1 Display the Special Device List screen 2 Enter PIN code 2 Select a model name 2 1 1 2 3 3 3 4 1 2 3 4 4 Enters a code number. Cancels registration of PIN code.
Setup Menu Bluetooth Unit Connection Deleting Bluetooth Unit Selects the Bluetooth unit to connect. Deletes the registered Bluetooth unit. 1 Display the Connect Device List screen 1 Display the Connect Device List screen 2 Select a registered Bluetooth unit 2 Select a Bluetooth unit to delete 1 2 3 1 Displays the registered Bluetooth unit. 2 Scrolls the name of the Bluetooth unit. 3 Returns to the previous screen.
DivX Setup Setup Memory Checks the registration code. This code is needed when making a disc which has DRM (Digital Rights Management). Audio Setup and AV Interface settings can be memorized. The memorized settings can be recalled at any time. For example, even when the settings are cleared due to replacement of the battery, the settings can be restored. 1 Display the DivX Setup screen Touch Menu" screen (page 62).
Setup Menu 6 Clears the currently memorized settings. 7 Returns to "SETUP Memory" screen. 3 Memorize or recall the settings When memorizing the Audio Setup and AV Interface settings: EXT SW Setup Setting up power specification of the external device for which the power is controlled from this unit. 1 Display the EXT SW SETUP screen Touch Menu" screen (page 62). in the "SETUP 2 Perform EXT SW Setup If settings have already been memorized, a confirmation message appears. Touch Yes .
Setting EXT SW Control 2 (EXT SW2) The setup method is the same as "EXT SW1". English B64-4093-00̲00̲EN.indb 87 87 08.2.
Audio Control Audio Control Menu Audio Control Displays the Audio Control menu to set the sound effect function of this unit. You can adjust the front/rear and right/left audio balance. 1 Display the control screen of any source 1 Display Audio Control screen Touch in the "Audio Control Menu" screen (page 88). 2 Set the each item Press several times until the control screen appears. 1 4 2 2 Display the Audio Control menu 3 3 4 5 1 Moves to the "Audio Control 2" screen.
• You may not set some models of power amp boost to "+18". See the catalog or instruction manual of power amplifier. Graphic Equalizer Setup You can Manually set the equalizer curve. 1 Display the Parametric Equalizer screen Equalizer Control You can setup the equalizer. 1 Display Equalizer Control Touch in the "Audio Control Menu" screen (page 88). 2 Display the Equalizer screen 1 1 2 3 1 1 Selects an equalizer curve type. You can select any of the following equalizer curves.
Audio Control Zone Control ⁄ You can set the front and rear audio source. • There are following limitations when zone function is set to "On". - There is no output from the subwoofer. -
SRS WOW User Setup Surround Control You can adjust the audio SRS. You can set up the sound field. 1 Display the Audio SRS Adjust screen 1 Display the Surround Control screen Touch in the "Audio Control Menu" screen (page 88). 2 1 1 2 Adjust the Audio SRS 3 4 1 2 1 Sets a sound field. You can select any of the following sound fields. • "Bypass" • "Bypass+Center" • "Dolby PLII Movie" • "Dolby PLII Music" • "Dolby PLII Matrix" 2 Displays the present source information.
Audio Control Surround Control Adjustment Position You can adjust the sound field. You can adjust the sound effects according to your listening position. 1 Display the Surround Control screen 1 Display the Position screen Touch in the "Audio Control Menu" screen (page 88). 1 2 Adjust the sound field 2 3 1 1 2 2 4 1 Sets a listening position. You can select any of "Front R" (Right front), "Front L" (Left front), "Front All" (All front), and "All" (All) positions.
Position Fine Control 3 Set a delay time You can fine-adjust your listening position. 1 Display the Position Fine Control screen 2 1 2 3 4 1 Selects a speaker to be adjusted. 2 Indicates setup distance. The adjusted distance (Position and Position Fine Control values), and the total of the distance adjusted by Car Type Set Up (page 62) and the adjustment distance for position setup are indicated. 3 Adjust the distance to each speaker.
Remote Controller This unit can be operated using the Remote Controller supplied with the unit. ¤ • Put the Remote Controller in a place where it will not move during braking or other operations. A dangerous situation could result, if the Remote Controller falls down and gets wedged under the pedals while driving. • Do not place the battery near an open flame or heat source. This may cause the battery to explode. • Do not recharge, short, break up or heat the battery or place it in an open fire.
Common operations (AUD mode) Source switching Switches to the source to be played. Display angle Switches the display angle each time it is pressed. O ROUTEM DISP CANCEL VOICE AV OUT OPEN VIEW MAP DIR SUBTITLE V.SEL IN POSITION O Cursor key Moves the cursor when displaying menu.
Remote Controller DVD/DVD Audio/VCD/CD/Audio files (DVD mode) Folder search Selects the folder to be played. ANGLE FM+ O O O D O VOL ZOOM O AM− Y 1 Group number Track number Item number* Cancel O DVD Audio 2 ZONE * You may not be able to use this function with some discs or scenes. 2ABC 3 DEF 1 CD Track search and file search Selects the track or file to be played. VIEW MAP DIR ANGLE FM+ O O D O O VOL ZOOM O AM− Y 1 O 1 Play/Pause Pauses the track.
O O MODE/TOP MENU FNC/MENU/PBC OPEN MAP DIR Band switching Switches to bands received by the unit. AUDIO RETURN CANCEL VOICE VIEW Radio (AUD mode) SUBTITLE ANGLE O FM+ O ANGLE O O O NAVI AUDIO RETURN CANCEL VOICE OPEN SUBTITLE ANGLE O Station selection Switches to broadcast stations received by the unit.
Remote Controller ZOOM IN MODE/TOP MENU FNC/MENU/PBC POSITION O AUD O OPEN VIEW MAP DIR • TV• • NAVI AUDIO RETURN CANCEL SUBTITLE ANGLE TV• • NAVI AUDIO RETURN VIEW Switches between 2D and 3D map displays. ZOOM OUT VOICE DVD • ENTER Performs the selected function.
TV (TV mode) Switching Band/Video It switches between the station of the TV band to receive and video input. CANCEL VOICE OPEN VIEW MAP DIR SUBTITLE ANGLE O FM+ D O O O ZOOM O ROUTEM AV OUT VOL O AM− Y 2 ZONE Channel Selection The TV channel to receive is selected. VIEW MAP DIR FM+ O O O D O 1 ZOOM O ANGLE VOL O AM− Y 2 ZONE 2ABC 3 DEF Direct tuning (NTSC TV type only) R.
DVD Language Codes Code Language Code Language Code Language aa ab af am ar as ay az ba be bg bh bi bn bo br ca co cs cy da de dz el en eo es et eu fa fi fj fo fr fy ga gd gli gn gu ha he hi hr hu hy ia ie ik id Afar Abkhazian Afrikaans Amharic Arabic Assamese Aymara Azerbaijani Bashkir Byelorussian Bulgarian Bihari Bislama Bengali, Bangla Tibetan Breton Catalan Corsican Czech Welsh Danish German Bhutani Greek English Esperanto Spanish Estonian Basque Persian Finnish Fiji Faroese French Frisian Irish
English B64-4093-00̲00̲EN.indb 101 101 08.2.
Help? Troubleshooting Some functions of this unit may be disabled by some settings made on this unit. ! ! ! ! • Cannot set up the subwoofer. • Cannot set up subwoofer phase. • No output from the subwoofer. • Cannot set up the low pass filter. • Cannot set up the high pass filter. ▲ Subwoofer is not set to On. ☞
Help? Error When the unit fails to operate correctly, the cause of the failure appears on the display. Protect : Protective circuit has been activated because a speaker cord has shorted or it has come in contact with the car chassis. Error 07–67: The unit is not operating correctly due to some reason or other. ➡ Push the unit's Reset button. If the "Error 07−67" message does not disappear, see your nearest Kenwood dealer. ➡ Wire or insulate the speaker cord as appropriate and then push the Reset button.
Specifications Monitor section USB interface section Picture Size : 6.95 inches (diagonal) wide : 156.2 mm (W) x 82.4 mm (H) Display Sytem : Transparent TN LCD panel Drive System : TFT active matrix system Number of Pixels : 336,960 (480H x 234V x RGB) Effective Pixels : 99.99 % Pixel Arrangement : RGB striped arrangement Back Lighting : Cold Cathode Fluorescent Tube USB Standard : USB 1.1/ 2.
Video section Bluetooth section Color System of External Video Input : NTSC/ PAL External Video Input Level (RCA jack) : 1 Vp-p/ 75 Ω External Audio Max Input Level (RCA jack) : 2 V/ 25 kΩ Video Output Level (RCA jacks) : 1 Vp-p/ 75 Ω Audio Output Level (RCA jacks) : 1.2 V/ 10 kΩ Analog RGB input (DDX8022BT only) : 0.7 Vp-p/ 75 Ω Technology : Bluetooth Ver.1.2 Certified Frequency : 2.402 – 2.480 GHz Output Power : +4dBm (MAX), 0dBm (AVE), Power Class2 Maximum Communication range : Line of sight approx.
Music disc play Navigation section (DNX8220BT only) Receiver : High-sensitivity GPS receiver Reception Frequency : 1575.42 MHz (C/A code) Acquisition Times Cold : < 38 seconds Factory Reset : < 45 seconds (On average for a stationary receiver with a clear view of the sky) Accuracy Position : < 10 meters typical Velocity : 0.05 m/sec. RMS Position Method : GPS Antenna : External GPS antenna General Operating voltage : 14.4 V (10.
The marking of products using lasers (Except for some areas) CLASS 1 LASER PRODUCT The label is attached to the chassis/case and says that the component uses laser beams that have been classified as Class 1. It means that the unit is utilizing laser beams that are of a weaker class. There is no danger of hazardous radiation outside the unit.
English Hereby, Kenwood declares that this unit DNX8220BT/DDX8022BT is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Français Par la présente Kenwood déclare que l’appareil DNX8220BT/DDX8022BT est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE.
