DNX996XR DNR876S DNX696S DNX576S DNR46EX DNR476S GPS NAVIGATION SYSTEM INSTRUCTION MANUAL • Updated information (the latest Instruction Manual, system updates, new functions, etc.) is available from . • The Instruction manual is subject to change for modification of specifications and so forth. Be sure to download the latest edition of the Instruction manual for reference. Take the time to read through this instruction manual.
Contents Before Use 4 APPS 34 Precautions.................................................................... 4 Wireless Mirroring Operation................................34 Safety Precautions and Important Information................................ 5 Apple CarPlay Operation........................................34 How to read this manual.......................................... 6 Spotify Operation......................................................
SiriusXM® 60 Controlling Audio 95 SiriusXM® Basic Operation.....................................60 3-way speaker system setup.................................95 Storing Channels in Preset Memory...................62 Speaker / X’over setup.............................................96 Preset select................................................................62 Controlling General Audio.....................................98 Direct search.......................................................
Before Use Before Use Precautions # WARNINGS ÑÑTo prevent injury or fire, take the following precautions: • To prevent a short circuit, never put or leave any metallic objects (such as coins or metallic tools) inside the unit. • Do not watch or fix your eyes on the unit’s display when you are driving for any extended period. • If you experience problems during installation, consult your KENWOOD dealer.
Before Use ÑÑAcquiring GPS signal The first time you turn on this unit, you must wait while the system acquires satellite signals for the first time. This process could take up to several minutes. Make sure your vehicle is outdoors in an open area away from tall buildings and trees for fastest acquisition. After the system acquires satellites for the first time, it will acquire satellites quickly each time thereafter.
Before Use # CAUTION Failure to avoid the following potentially hazardous situations may result in injury or property damage. The navigation system is designed to provide you with route suggestions. It does not reflect road closures or road conditions, weather conditions, or other factors that may affect safety or timing while driving. Use the navigation system only as a navigational aid.
Basic Operations Basic Operations Functions of the Buttons on the Front Panel DNX996XR 9 10 1 2 3 4 5 6 7 DNR876S 10 1 2 DNX696S / DNX576S 11 3 4 5 9 6 8 1 4 2 3 5 6 English 7
Basic Operations DNR46EX / DNR476S 11 1 4 2 3 5 6 NOTE • The panels shown in this manual are examples used to provide a clear explanation of operations. For this reason, they may be different from the actual panels. Number Name Remote Sensor • Receives the remote control signal. 2 S, R (Volume) • Adjusts the volume. The volume will go up to 15 when you keep pressing R. (P.11) 3 NAV/[ ] • Displays the navigation screen. • Pressing and holding turns the screen off.
Basic Operations Number Name Motion 9 Disc insert slot • A slot to insert a disc media. (DNX996XR / DNX696S / DNX576S only) 10 SD card slot • A slot to insert an SD card. • You can play audio/visual files in the card. *1 • An SD card slot for upgrading the map. For how to upgrade the map, refer to the instruction manual of the navigation system. *2 *1 If the map update file remains in the SD card, you cannot play audio/visual files.
Basic Operations Initial Settings (DNX996XR / DNR876S only) 5 Touch [Display Adjustment]. 6 Adjust a viewing angle and a tilt position. 7 Touch [ ]. For details, see Display Adjustment (P.12). Initial setup Perform this setup when you use this unit first time. 1 Set each item as follows. (DNX696S / DNX576S / DNR46EX / DNR476S only) 5 Touch [Viewing Angle]. 6 Select a viewing angle. 7 Touch [ ]. For details, see Viewing Angle (P.12). For details, see Display Setup (P.92).
Basic Operations Calendar/clock settings 1 Press the [MENU]/[ ] button. hh Popup menu appears. 2 Touch [SETUP]. hh SETUP Menu screen appears. 3 Touch [User Interface]. NOTE • Please set the date and time. If they are not set, some functions may not work. Adjusting the volume You can adjust the volume (0 to 40). Press [R] to increase, and press [S] to decrease. Holding [R] increases the volume continuously to level 15.
Basic Operations Display Adjustment (DNX996XR / DNR876S) Viewing Angle (DNX696S / DNX576S / DNR46EX / DNR476S) DNX996XR 1 Press the [G] button. hh Display Adjustment screen appears. DNR876S You can adjust the viewing angle when the image on the screen is difficult to see evenly. The smaller the (negative) value, the more whitish the image on the screen looks. 1 Press the [ ] button. hh Popup menu appears. You can set up following items from this screen. 2 Touch [SETUP].
Basic Operations Touch screen operations To perform operations on the screen, you need to touch, touch and hold, flick or swipe to select an item, display a setting menu screen or change pages. HOME screen descriptions Most functions can be performed from the HOME screen. 1 ●● Touch Touch the screen gently to select an item on the screen. ●● Touch and hold Touch the screen and keep your finger in place until the display changes or a message is displayed.
Basic Operations Popup menu Turn off the screen 1 Press the [MENU]/[ ] button. hh Popup menu appears. 1 2 Touch to display the popup menu. DNX996XR / DNR876S / DNR46EX / DNR476S Select [Display OFF] on the popup menu. NOTE • Touch the display to turn on the screen. • To display the clock while the screen is off, it is necessary to set "OSD Clock" to "ON". (P.92) Source selection screen description 1 You can display icons of all playback sources and options on the source selection screen.
Basic Operations Select the playback source 1 Press the [HOME]/[ ] button. hh HOME screen appears. 2 Touch [ ]. From the screen, you can select the following sources and functions. • Displays the navigation screen. (P.18) • Switches to the Apple CarPlay screen from the connected iPhone. (P.34) • Switches to the Android Auto screen from the connected Android device. (P.38) • Displays the Hands Free screen. (P.
Basic Operations To select the playback source on the source control screen Customize Short-cut source icons on HOME screen You can arrange the positions of the source icons as you like. Display source selection icons by touching [ ]/[ ] or flicking left or right on the source control screen, then select a playback source. 1 Press the [HOME]/[ ] button. hh HOME screen appears. 2 Touch [ 3 Touch and hold the icon which you want to move in the customizing mode.
Basic Operations Source control screen descriptions 4 • Connected Bluetooth device information. 5 Artwork & information There are some functions which can be performed from most screens. You can select whether to display an artwork and song information or only song information in more detail. Touching the artwork area switches to the VU meter.
Basic Operations List screen 5 [ There are some common function keys in the list screens of most sources. See (P.31, 47, 49, 77). ] Page scroll NOTE • Depending on the current source or mode, some function key may not appear. Touch [1] or the item listed on the information area in the source control screen. hh The list screen appears. Navigation Operation For Bluetooth audio: For details on the navigation function, please refer to the Navigation Instruction Manual. Touch [1].
Basic Operations How to Use the Navigation System 1 NOTE • To enter letters contained in the name, touch the Search bar and enter the letters. Operate the desired function from the Main Menu screen. 1 3 2 3 4 5 1 GPS and GLONASS signal status. 2 Finds a destination. 3 Views the map. 4 Uses the Apps such as ecoRoute and Help. 5 Adjusts the settings. NOTE • GLONASS reception is not available on all device models.
Basic Operations 2 From the Map Updates section, select Update 3 Follow the on-screen instructions. NOTE • Touch and drag the map to view a different area of the map. • A speed limit icon could appear as you travel on major roadways. ●● Adding a stop ] and 1 While navigating a route, touch [ then touch [Where To?]. 2 Search for the extra stop. 3 Touch [Go!]. 4 Touch [Add to Active Route] to add this stop before your final destination. ●● Taking a detour 1 While navigating a route, touch [ 2 Touch [ ].
Basic Operations Displays the navigation and view camera display. Returns to the full navigation screen. NOTE • For details on control keys, refer to the instructions in each section. • Touching the source icon at the bottom of the screen displays the full audio screen. During video playback, touching the viewing area displays operation keys. • During camera view display, touching the viewing area switches to the view cameras set in the camera assignment settings. (P.
Basic Operations KENWOOD Traffic Powered By INRIX 2 You can receive INRIX traffic information and weather forecast by connecting your iPhone or Android smartphone in which the “KENWOOD Traffic Powered By INRIX” application is installed to this unit. Press the [NAV]/[ ] button. DNX996XR / DNR876S DNX696S / DNX576S / DNR46EX / DNR476S Preparation • Install the latest version of the KENWOOD Traffic Powered By INRIX application on your iPhone or Android.
Widget Widget Widget 1 2 Press the [HOME]/[ ] button. You can change the widget by flicking left or right on the widget area. Multi Widget You can place a widget on each of the following areas. Up to 4 widgets can be placed per a multi widget screen. 1 2 Press the [HOME]/[ ] button. Flick the widget area to the left/right to display the multi widget.
Widget ●● To replace the widget 1 Touch [ ] on the multi widget screen. 1 NOTE • [ ] and the widget list popup disappear when no operation is done for 5 seconds. • When the screen is switched from another widget to multi widget screen, [ ] appears again. ÑÑAdd a new multi widget You can add pages to the multi widget screen. 1 hh Widget list popup appears. Touch [ ] on the multi widget screen. hh Widget list popup appears.
Widget Weather Widget You can display the weather forecast of the present location on the Home screen. Preparation • See KENWOOD Traffic Powered By INRIX (P.22). • Select “ON” for Weather Widget. See Widget Setup (P.26). 1 2 Press the [HOME]/[ ] button. Flick the widget area to the left/right to display the weather widget. Photo Frame Widget You can display a slideshow of the image files stored in the USB memory/SD card on the Home screen. ÑÑPreparation • Select “ON” for Photo Frame Widget.
Widget Widget Setup To Photo Frame Setup Set up the widgets on the Home screen. Make settings related to display of the photo frame widget. 1 Press the [MENU]/[ ] button. hh Popup menu appears. 1 Touch [Photo Frame SETUP] on the Widget SETUP screen. 2 Touch [SETUP]. hh SETUP screen appears. 2 Set each item as follows. 3 ■■ [Sort Order] Specify a file sorting criterion.
Disc Disc (DNX996XR / DNX696S / DNX576S) Playing a disc ÑÑInsert a disc DNX996XR 1 Press the [G] button. 2 Touch [DISC EJECT]. hh The panel opens. 3 Insert the disc into the slot. ÑÑEject a disc DNX996XR 1 2 Press the [G] button. 3 Press the [G] button. hh The panel closes. Touch [DISC EJECT]. When removing a disc, pull it horizontally. NOTE • To forcibly eject the disc, press and hold the [[G] button for 2 seconds and then touch [DISC EJECT] after the message is displayed.
Disc DVD/VCD Basic Operation • Linear PCM, etc.: Audio format • OFF/Zoom2 – 4 (DVD)/Zoom2 (VCD): Displays the zoom ratio. This function can be used from the remote control. (P.104) • [Hide]: Hides the control screen. •[ ] : Repeats the current content.
Disc 4 Operation keys • [E] [F] : Searches for the previous/next content. Touch and hold to fast-forward or fastbackward the disc. (It will be cancelled automatically after about 50 seconds.) • [DH] : Plays or pauses. •[ ] : Displays the Graphic Equalizer screen. (P.98) 5 Indicator Items • [IN]: Disc insertion status. White: A Disc is inside the unit. Orange: Disc player failure. VCD • [1chLL/2chLL]: Identifies the left audio output of channel 1 or 2.
Disc •[ ] : Repeats the current track/folder. Each time you touch the key, repeat mode switches in the following sequence; Track/File repeat ( ), Folder repeat ( ) (Disc media only), Repeat all ( ) •[ ] : Randomly plays all tracks in current folder/disc. Each time you touch the key, random mode switches in the following sequence; Track random ( ) (Music CD only), Folder ) (Disc media only), Random off random ( ( ) 2 Track information • Displays the information of the current track/file.
Disc File search Operation (Disc media only) You can search for a file according to hierarchy. NOTE DVD Disc Menu Operation You can set up some functions using the DVDVIDEO disc menu. 1 Touch the framed area during playback. • For operations in the list screen, see List screen (P.18). 1 Touch [1]. hh Folder List screen appears. 2 Touch the desired folder. hh Menu Control screen appears. 2 Perform your desired operation as follows. hh When you touch a folder its contents are displayed.
Disc ■■ To switch among picture angles Touch [Angle]. Each time you touch this key, picture angles are switched. * These keys may not function depending on the disc. DVD Setup You can set up the DVD playback functions. 1 Touch the framed area during playback. 2 Touch [ ] on the left side of the screen. Touch [SETUP]. ÑÑHighlight control Highlight control lets you control the DVD menu by touching the menu key directly on the screen. 1 Touch [Highlight] on the Menu Control screen.
Disc ■■ [Screen Ratio] Sets the screen display mode. [16:9 ](Default): Displays wide pictures. [4:3 LB]: Displays wide pictures in the Letter Box format (having black stripes at the top and bottom of screen). [4:3 PS]: Displays wide pictures in the Pan & Scan format (showing pictures cut at the right and left ends). ÑÑLanguage setup This setting is for the languages used for the menu, subtitle, and voice. 1 Touch the desired item; [Menu Language], [Subtitle Language], [Audio Language].
APPS APPS Wireless Mirroring Operation (DNX996XR / DNR876S) You can display the same screen of the Android device on the monitor of the unit using the Wireless Mirroring function of the Android device. Preparation • You can use the Wireless Mirroring function with Android devices compatible with this function. • This function may be called Wireless Display, Screen Mirroring, AllShare Cast, etc., depending on the manufacturer. • The settings on the Android device differ depending on the device type.
APPS ÑÑConnecting an iPhone Wired connection 1 Connect your iPhone using KCA-iP103 via the USB (Black) terminal. (P.115) When an iPhone compatible with Apple CarPlay is connected to the USB (Black) terminal, the Bluetooth Hands-Free phone currently connected is disconnected. If the Bluetooth Hands-Free phone is being used, disconnection will occur after ending the call. 2 Unlock your iPhone.
APPS ÑÑSelect an Apple CarPlay device To delete the registered Apple CarPlay device If two or more iPhones compatible with Apple CarPlay have been registered, select the iPhone to be used as the Apple CarPlay source. 1 2 (DNX996XR / DNR876S) 1 Press the [MENU]/[ ] button. hh Popup menu appears. 2 Touch [SETUP]. hh SETUP screen appears. 3 Touch [AV]. 4 5 Touch [ ]. Touch the device name to check. ■■ [þ [ALL] Selects all Apple CarPlay devices. Touch [Apple CarPlay Device List].
APPS ÑÑOperation buttons and DNX696S / DNX576S / DNR46EX / DNR476S available Apps on the home screen of Apple CarPlay You can use the Apps of the connected iPhone. The items displayed and the language used on the screen differ among the connected devices. To enter the Apple CarPlay mode, touch [Apple CarPlay] icon on the source selection screen. (P.15) 2 Press for 1 second 2 Talk to Siri. To deactivate 1 Press the [ ] button.
APPS Android Auto™ Operation Android Auto enables you to use the functions of your Android device convenient for driving. You can easily access route guidance, make calls, listen to music, and access convenient functions on the Android device while driving. For details about Android Auto, visit https:// www.android.com/auto/ and https://support. google.com/androidauto. Compatible Android devices You can use Android Auto with Android devices of Android version 5.0 (Lollipop) or later.
APPS ÑÑOperation buttons and ÑÑSwitch to the Android Auto You can perform the operations of the Apps of the connected Android device. The items displayed on the screen differ among the connected Android devices. To enter the Android Auto mode, touch the [Android Auto] icon on the source selection screen. (P.15) 1 available Apps on the Android Auto screen screen while listening to another source Press the [ ] button.
APPS Spotify Operation 3 Operation keys •[ You can listen to Spotify on this unit by controlling the application installed in the iPhone or Android. To select the Spotify source, touch [Spotify] icon on the source selection screen. (P.15) •[ ],[ ] : Skips the current song. (Note that this function is disabled when the Spotify skip limitation is exceeded.) Preparation • Install the latest version of the Spotify application "Spotify" on your iPhone or Android.
APPS ■■ [ Top] Returns to the top of the list. Up] ■■ [ Returns to the previous list. About Spotify® Note • Ensure you are logged in to your smartphone application. If you do not have an Spotify account, you can create one for free from your smartphone or at www.spotify.com. • Because Spotify is a third-party service, the specifications are subject to change without prior notice. Accordingly, compatibility may be impaired or some or all of the services may become unavailable.
APPS Pandora® Operation You can listen to Pandora® on this unit by controlling the application installed in the iPhone or Bluetooth device. To select the Pandora source, touch the [Pandora] icon on the source selection screen. (P.15) Preparation • Install the latest version of the Pandora® application on your iPhone, Android or BlackBerry. iPhone: Search for "Pandora" in the Apple App Store to find and install the most current version. Android: Visit the Google play and search for Pandora to install.
APPS Genre list screen NOTE • You can operate Pandora by using the remote control function. However, you can perform only play, pause, and skip operations. 1 Touch [Create station from genre]. 2 The selected genre is created as a new station. ÑÑCreates a new station 1 2 Touch [ ]. Touch your desired item. ■■ Create station from artist Creates a new station based on the artist who is playing now. ■■ Create station from track Creates a new station based on the song being played.
USB/SD USB/SD Connecting a USB device 1 2 3 4 Connect the USB device with the USB cable. (P.114) Press the [HOME]/[ ] button. Touch [ Inserting the SD DNX996XR 1 Press the [G] button. 2 3 Touch [OPEN] to the panel fully opens. 4 5 6 7 Press the [G] button. Insert the SD card into the slot until it clicks. ]. Touch [USB]. (P.15) ÑÑDisconnect the USB device 1 2 3 Press the [HOME]/[ ] button. Touch a source other than [USB]. Detach the USB device.
USB/SD DNX696S / DNX576S / DNR46EX / DNR476S 1 2 3 4 Insert the microSD card into the slot until it clicks. Press the [ ] button. Touch [ ]. Touch [SD]. (P.15) ÑÑRemove the SD card DNX996XR 1 2 3 4 Press the [G] button. Touch [OPEN] to the panel fully opens. Push the SD card until it clicks and then remove your finger from the card. The card pops up so that you can pull it out with your fingers. Press the [G] button. DNR876S 1 2 3 Press and hold the [CAM] button.
USB/SD Close the drawer 6 5 Content list 5 7 • Touch the right side of the screen to display the Content list. Touch again to close the list. • Displays the playing list. When you touch a track/file name on the list, playback will start. 6 Artwork/VU meter 8 1 [CODEC]/[ ]/[ ] • When a high-resolution source is played, its format information is displayed. •[ ] : Repeats the current track/folder.
USB/SD Search Operation You can search music or video files by the following operations. 1 2 Touch [1]. 3 Select a list type. Touch [S]. ÑÑLink search You can search for a file of the same artist/ album/genre as that in the current track. 1 2 ÑÑCategory search You can search for a file by selecting a category. 1 2 3 Touch [Category List]. Touch the desired tag type. You can select from artists, albums and genres. hh The list corresponding to your selection appears.
iPod/iPhone iPod/iPhone Preparation 1 Connect the iPod/iPhone using the KCAiP103. (P.115) ÑÑConnectable iPod/iPhone 2 3 4 Press the [HOME]/[ ] button. The following models can be connected to this unit. Made for • iPhone X • iPhone 8 Plus • iPhone 8 • iPhone 7 Plus • iPhone 7 • iPhone SE • iPhone 6s Plus • iPhone 6s • iPhone 6 Plus • iPhone 6 • iPhone 5s • iPhone 5c • iPhone 5 • iPod touch (6th generation) NOTE • Latest compatible list of iPod/iPhone. For details, see www.kenwood.com/cs/ce/ipod/.
iPod/iPhone Open the drawer 6 2 5 5 Content list • Touch the right side of the screen to display the Content list. Touch again to close the list. • Displays the playing list. When you touch a track/file name on the list, playback will start. 6 [ Close the drawer 2 5 ]/[ ] •[ ] : Repeats the current track/album. Each time you touch the key, repeat modes are switched in the following sequence: ), All songs repeat ( ), Song repeat ( Repeat off ( ) •[ ] : Randomly plays all tracks in the current album.
iPod/iPhone ÑÑCategory search You can search for a file by selecting a category. 1 2 Touch [Category List]. Touch the desired category. hh The list corresponding to your selection appears. 3 Touch to select the desired item in the list. Repeat this step until you find the desired file. ÑÑLink search You can search for a file of the same artist/ album/genre/composer as that in the current track. 1 2 Touch [Link Search]. Touch the desired tag type.
Radio Radio (DNX576S / DNR46EX / DNR476S) Radio Basic Operation 1 Information display • Displays the information on the current station: Frequency Touching [ ] allows you to switch between Content A and Content B. Content A: PS name, Radio Text, Title & Artist Content B: PTY Genre, Radio Text plus Preset#: Preset number • Change the text size of the information smaller when the "Small Audio Text" is set to "ON" in the User Interface screen (P.90).
Radio • [PTY] (FM only) : Searches for a program by program type. For details, see Search by program type (P.53). • [MONO] (FM only) : Selects the Monaural reception mode. 7 Indicator Items • [ST]: A stereo broadcast is being received. • [MONO]: The forced monaural function is active. • [TI]: Indicates the reception state of traffic information. White: TP is being received. Orange: TP is not being received.
Radio Selecting Operation ÑÑPreset select You can list and select memorized stations. 1 Touch [ ] on the right side of the screen. Select a station from the list. Traffic Information (FM only) You can listen to and watch traffic information automatically when a traffic bulletin starts. However, this feature requires a Radio Broadcast Data System that includes TI information. 1 Touch [ ] on the left side of the screen. Touch [TI].
HD Radio™ Tuner HD Radio™ Tuner (DNX996XR / DNR876S / DNX696S) HD Radio Tuner Basic Operation 1 Information display Most functions can be controlled from the source control screen. To listen to the HD Radio source, touch [HD Radio] icon on the source selection screen. (P.15) NOTE • Set the remote control mode switch to AUD mode before starting operation, see Switch the operation mode (P.104). • HD Radio broadcasting is for North American sales area only. • The screen shot below is for tuner.
HD Radio™ Tuner 5 Operation keys • [E] [F] : Tunes in a station. The method of switching frequencies can be changed (see 2 Seek mode). • [CHS] [CHR] : Selects a channel. • [1] : Display the Channel List screen. See Channel search (P.57). • [ ] : Display a list of registered bookmarks. See Bookmark list (P.58). •[ ] : Displays the Graphic Equalizer screen. (P.98) 6 Preset list • Touching [ ]/[ ] allows you to change the display size. • Recalls the memorized station or channel.
HD Radio™ Tuner Receive Mode 2 Touch [ ] on the left side of the screen. Touch [AME]. 3 Touch [Yes]. You can set the radio broadcasts receive mode. 1 2 Touch [ ] on the left side of the screen. Touch [RCV]. Select a receive mode. hh Auto memory starts. ÑÑManual memory You can store the currently being received station or channel in the memory. ■■ [Auto] Switch between digital and analog audio automatically. 1 Select the station or channel you wish to store in the memory.
HD Radio™ Tuner ÑÑDirect search 2 Select the desired content from the list. You can tune in by entering the desired frequency or channel number. 1 Touch [ ] on the left side of the screen. Touch [10key Direct]. NOTE • Touch [Info Change] in the channel list. Select the sequence of the list (Song title, artist name, album name). 2 Select the search method. ÑÑSearch by program type (FM only) You can tune in the station broadcasting the specified type of program when listening to FM.
HD Radio™ Tuner Bookmark Stores tag information (title, artist, album, URL, and description) about the song you are listening to now. Detailed information and QR codes can be displayed according to the stored tag information. ÑÑBookmark registration 1 Touch [ Touch [ ] on the left side of the screen. ]. ■■ [ Delete] Deletes the bookmarks being displayed. Bookmark delete Deleting a bookmark. hh Registers a bookmark. 1 Touch [Delete]. 2 Select the bookmark to delete from the list.
HD Radio™ Tuner Alert Message This function is to receive alert messages. First, you need to turn on the “Emergency Alerts”. (P.54) ÑÑWhen an Alert Message comes [Snooze] ÑÑDisplay of the received Alert Message You can read the received alert message afterward. 1 Touch [ ] on the left side of the screen. Touch [Alert Message Log]. 2 Select the desired Alert Message from the list. The alert message is erased. Same alert message cannot be displayed for next 10 minutes.
SiriusXM® SiriusXM® SiriusXM® Basic Operation Only SiriusXM® brings you more of what you love to listen to, all in one place. Get over 140 channels, including commercial-free music plus the best sports, news, talk, comedy and entertainment. Welcome to the world of satellite radio. A SiriusXM Vehicle Tuner and Subscription are required. For more information, visit www.siriusxm.com. To listen to the SiriusXM source, touch the [SiriusXM] icon on the source selection screen. (P.
SiriusXM® • Change the text size of the information smaller when the "Small Audio Text" is set to "ON" in the User Interface screen (P.90). NOTE • While getting contents, "Waiting" is showing on the display. 2 Band button Switches among bands. (SXM1/SXM2/SXM3/ SXM4) 3 Artwork • Displays/hides artwork area. • Displays the album artwork for most SiriusXM music channels 4 Operation keys • [1] : Display the Category search screen. For details on search operation, see Category/ Channel search (P.63).
SiriusXM® Storing Channels in Preset Memory You can store the current channel in memory. 1 Tune in the channel you wish to store in the memory. 2 Touch [ 3 Direct search You can tune in a channel directly. 1 Touch [ ] on the left side of the screen. Touch [Direct Channel]. 2 Enter the channel number and touch [Enter]. ] on the right side of the screen. Touch [SXM(1-4) P(1-6)] in which you want to store the channel for 2 seconds until a beep sounds.
SiriusXM® Category/Channel search Replay You can specify the desired category and select a channel. You can replay the last 60 minutes of the program from the current channel. 1 Touch [1]. 1 2 Select a category. ■■ [E] [F] Press to skip to the previous/next track. Press and hold to rewind or fast forward. (It will be cancelled automatically after about 50 seconds.) hh Channel list appears. 3 Touch [L] or [Replay] on the function panel. Select the desired content from the list.
SiriusXM® ■■ [Info Change] Touch [Info Change]. Select a desired item: content info, channel name, artist name, song title, category name. To return to live music/content 1 2 Touch the left side of the screen. Touch [Live]. TuneMix™ TuneMix™ plays a unique blend of songs from your Preset music channels of the current SiriusXM Preset Band, allowing you to build a custom channel from as few as two to as many as 6 music channels. You can even skip songs you don’t want to hear.
SiriusXM® Content Alerts NOTE • To cancel TuneScan™, touch the left side of the screen. Touch [TuneScan]. • Touch and hold [TuneScan] to cancel TuneScan, and the music/content which was present on the channel before starting TuneScan will be played. • Compatible with SXV200 or later tuner models. When a broadcast program related to the registered artist, song or team starts, an Alert Content List screen appears to allow you to switch the current channel to the relevant channel.
SiriusXM® SportsFlash™ SportsFlash™ will notify you when a big play happens during a game with one of your favorite sports teams. Choose to tune in and hear the play unfold like it was live. Continue listening to the game or return to your previous channel. 1 1 Touch [ ] on the left side of the screen. Touch [SETUP]. When a big play happens during one of the games, an Alert screen appears. ■■ [Listen] Touch to tune in that channel and play back the big play.
SiriusXM® ÑÑParental code ÑÑParental Control You can set a SiriusXM parental code for Parental Control. Parental Control is a feature that provides the user with the ability to prevent unauthorized access to mature content and user selected channels. 1 Touch [Parental Code] on the SiriusXM SETUP screen. hh Parental Pass Check screen appears. NOTE • The code number is set to “0000” as default. 2 1 Touch [Parental Control] on the SiriusXM SETUP screen. 2 Touch [User], [Mature] or [OFF].
SiriusXM® NOTE 3 • Touch [All-Channels] to display all channels. • To delete the parental lock channel setting, touch [Disable All] and then touch [YES] on the confirmation screen. 4 Touch each channel in the list and set to ON or OFF. Touch each channel on the list and set to ON or OFF. [ON]: Locks the channel. [OFF]: Unlocks the channel. NOTE • To delete the skip channel setting, touch [Disable All] and then touch [YES] on the confirmation screen. • Touch [Info Change].
SiriusXM® 3 Touch each content list item you want to select ON or OFF. NOTE • You can select up to 60 artists or songs. To select a Team Get alerted when your favorite sports team is playing on another SiriusXM channel with GameAlert™ 1 Touch [My Games]. 2 Touch the desired league in the list. 3 Touch the team(s) in the list you want to select. ●● To delete the Artist and Song 1 Touch [Delete]. 2 Touch the content(s) in the list you want to select. ■■ [þ All] Selects all contents.
SiriusXM® ÑÑSportsFlash™ setup 5 Touch [ ] twice. Activating SportsFlash 1 Touch [SportsFlash] on the SiriusXM SETUP screen. hh SportsFlash is turned on or off. Default is “ON”. Selecting SportsFlash Beep 1 Touch [SportsFlash Beep] on the SiriusXM SETUP screen. hh SportsFlash Beep is turned on or off. Default is “ON”. ■■ [Edit] Sets and removes teams. ■■ [Priority] Sets the priority of a team. Selecting the teams for SportsFlash 1 Touch [SportsFlash Team Set] on the SiriusXM SETUP screen.
SiriusXM® 3 Touch [Done]. ÑÑTuneStart™ 1 Touch [Tune Start] on the SiriusXM SETUP screen. The TuneStart is turned on or off. Default is “ON”. ÑÑReset NOTE 1 • Priority can be set on up to 5 teams. • When priority has already been set for 5 teams, it cannot be set for any other team. Delete an unnecessary team. Touch [SiriusXM Reset] on the SiriusXM SETUP screen. hh Confirmation screen appears. 2 Touch [YES]. hh All SiriusXM settings are reset to defaults.
Bluetooth Control Bluetooth Control Using the Bluetooth function allows you to use various functions such as listening to the audio file and making/receiving a call. Information for using Bluetooth® devices Bluetooth is a short-range wireless radio communication technology for mobile devices such as cell-phones, portable PCs, and other devices. Bluetooth devices can be connected without cables and communication with each other.
Bluetooth Control Register the Bluetooth device 5 Touch [ ] on the Select Device screen. It is necessary to register the Bluetooth audio player or cell-phone in this unit before using the Bluetooth function. You can register up to 10 Bluetooth devices. NOTE • Up to 10 Bluetooth devices can be registered. If an attempt is made to register the 11th Bluetooth device, the Bluetooth device connected on the earliest date will be deleted to register the 11th one.
Bluetooth Control 8 Select the function you want to use. ■■ HFP [Hands Free1]/[Hands Free2]/[No Connection.] Select the hands-free number to connect. ■■ A2DP/SPP [Audio/App] Select if you want to use the audio player app in your smartphone over A2DP, and the other apps in your smartphone over SPP. ■■ PBAP [Phonebook DL] Select if you want to transfer your phonebook data. 9 3 Touch [Bluetooth]. hh Bluetooth SETUP screen appears. See the following section for each setting.
Bluetooth Control ■■ [Audio (A2DP)/App (SPP)] Select to interwork with an application installed in a smartphone or to use as an audio player. 4 Touch [Close]. To delete the registered Bluetooth device 1 2 Touch [ ÑÑChange the device name 1 Touch [Device Name] on the Bluetooth SETUP screen. hh Change Device Name screen appears. 2 3 Touch and hold [ 4 Touch [Enter]. ]. Input the device name. ] on the Select Device screen. Touch the device name to check.
Bluetooth Control Playing the Bluetooth Audio Device •[ ] : Displays the Graphic Equalizer screen. (P.98) Most function can be controlled from the source control screen. To select Bluetooth source, touch [Bluetooth] icon on the source selection screen. (P.15) NOTE ÑÑBluetooth basic operation Control screen 5 6 2 3 1 Artwork/VU meter • Displays/hides artwork area. • Touch to switch between the artwork and VU meter.
Bluetooth Control ÑÑKENWOOD Music Mix Up to 5 Bluetooth audio device can be connected and switched easily to play music. 1 Touch [ ]. hh A list of registered devices is displayed. 2 Touch [ ] of device name you want to connect. • Touching [ ] displays the Bluetooth device connection setup screen. (P.74) ] on the left of the • Touching [ connected device ( ) disconnects this device. • • 3 NOTE • If a connected Bluetooth audio device is operated to play music, connections are switched.
Bluetooth Control Using the Hands-Free Unit 4 Select a dialing method. You can use the telephone function by connecting the Bluetooth telephone to this unit. NOTE • If you use the hands-free function frequently, move the TEL short-cut button (icon) to the Home screen. (P.16) • While Apple CarPlay or Android Auto is connected, the Bluetooth Hands-Free function and two Bluetooth devices connections cannot be used. Only the Apple CarPlay or Android Auto Hands-Free function can be used.
Bluetooth Control Call using call records 1 2 Touch [ 5 Select the phone number from the list. ]. Select the phone number from the list. NOTE • You can sort the phone numbers in the list by last name or first name. For details, see Hands-Free Setup (P.82). Call using the phonebook 1 2 3 Touch [ Touch [ Call using the preset number ]. ]. Select the initial. • Characters with no corresponding name will not appear.
Bluetooth Control ÑÑVoice Recognition You can access the voice recognition function of the cell-phone connected to this unit. You can search the cell-phone phonebook by voice. (The functionality depends on the cell-phone.) 1 Press the [ ] button for 1 second. DNX996XR / DNR876S Press for 1 second NOTE • While monitoring the picture from the view camera, this screen does not appear even if a call comes in. To end call 1 While talking, touch [ ].
Bluetooth Control DNX696S / DNX576S / DNR46EX / DNR476S ÑÑPhone number preset You can register frequently used phone numbers in this unit. 1 2 Touch [ 3 Select where to preset. ]. Touch [Edit]. ●● Mute your voice Touch [ ] to mute or not to mute your voice. ●● Output the dial tone Touch [DTMF] to display the tone input screen. You can send tones by touching desired keys on the screen.
Bluetooth Control ■■ [Delete] To delete a preset number, touch [Delete] and then touch [OK] on the confirmation screen. Hands-Free Setup You can make various settings for the HandsFree function. ÑÑPhonebook transfer 1 You can transfer phonebook data from your Bluetooth smartphone using PBAP. Press the [MENU]/[ ] button. hh Popup menu appears. 2 Touch [SETUP]. 1 2 Touch [ ]. Touch [ ]. hh SETUP Menu screen appears. 3 Touch [Bluetooth]. hh Phonebook data transfer starts.
Bluetooth Control ■■ [Auto Response]* Set the automatic response time to pick-up an incoming call. [OFF ](Default): Turns off the Automatic response function. [1]/[5]/[10]/[15]/[20]/[25]/[30]: Sets the ringing time (second). ■■ [Auto Pairing] When set to “ON”, the Apple Auto Pairing function is turned on to automatically register the iPod touch or iPhone connected to this unit. [ON ](Default): Turns on the Apple Auto Pairing function. [OFF]: Turns off the Apple Auto Pairing function.
Other External Components Other External Components View Camera 4 Switching the Angle *2 Touching each time changes camera angles. NOTE • To connect a camera, see P.113. • To use a rear view camera, a REVERSE lead connection is required. (P.112) • If [Rear Camera Interruption] is active the camera screen is displayed when you shift the gear to the reverse (R) position. ÑÑDisplay the camera screen 1 Press the [MENU]/[ ] button. hh Popup menu appears. 2 Touch [Camera].
Other External Components 4 Set each item as follows. ■■ Camera Assignment Settings Set up the camera assignment. See To set up the camera assignment settings (P.85). ■■ [Rear Camera Interruption] [ON]: Displays the picture from the rear view camera when you shift the gear to the reverse (R) position. [OFF ](Default): Select this when no camera is connected. ÑÑTo set up the camera assignment settings 1 Touch [Camera Assignment Settings] on the Camera screen. (P.84) 2 Set each item as follows.
Other External Components ÑÑTo adjust the parking For AV-IN input terminal: 1 2 Touch [AV-IN]. hh Displays the picture from view camera connected to AV-IN input terminal. Select the view camera to set up. 1 2 3 4 5 6 guidelines NOTE • Install the rear view camera in the appropriate position according to the instruction manual supplied with the rear view camera. • When adjusting the parking guidelines, make sure to apply the parking brake to prevent the car from moving.
Other External Components ÑÑAdded function Use Dashboard Camera A Dashboard Camera, DRV-N520 (optional accessory), connected to this unit lets you play video-recorded data and so on. For details, see the instruction manual of the Dashboard Camera DRV-N520 (optional accessory). NOTE Display the map while playing the recorded file 1 Play the recorded file. See the instruction manual of the Dashboard Camera. 2 Touch [ ]. • To connect a dashboard camera, see P.116.
Other External Components OEM Features Operation By connecting this unit to the bus system of the vehicle using an iDataLink (commercially available), this unit can access the satellite radio source provided for the vehicle and can display vehicle information on this unit. 1 Press the [HOME]/[ ] button. hh HOME screen appears. 2 3 Touch [ ] on the HOME screen. Touch icon. • Displays the control screen of the Bluetooth Hands Free function provided for the vehicle.
Setup Setup Monitor Screen Setup You can adjust the image quality of video, menu screen, etc. 1 Press the [MENU]/[ ] button. hh Popup menu appears. 2 Touch [Screen Adjustment]. System Setup 1 Press the [MENU]/[ ] button. hh Popup menu appears. 2 Touch [SETUP]. hh Screen Adjustment screen appears. 3 Adjust each setting as follows. ■■ [Backlight]/[Contrast]/[Black]/ [Brightness]/[Color]/[Tint] Adjust each setting. ■■ [Aspect] Select a screen mode.
Setup User Interface Setup You can setup user interface parameters. 1 Press the [MENU]/[ ] button. hh Popup menu appears. 2 Touch [SETUP]. hh SETUP screen appears. 3 Touch [User Interface]. hh User Interface screen appears. 4 Set each parameter as follows. ■■ [Language Select] Select a language. ■■ [Touch Panel Adjust] (Except DNX996XR) Adjust the sensing position of the touch panel. (P.91) ■■ [Time Format] Select the time display format.
Setup ÑÑAdjust the date and time Special Setup manually You can setup special parameters. 1 2 3 Touch [Clock] on the User Interface screen. 4 5 Select the time zone. 6 Adjust the date, then adjust the time. 1 Press the [MENU]/[ ] button. hh Popup menu appears. 2 Touch [SETUP]. hh SETUP screen appears. 3 Touch [Special]. Select [Manual]. Touch [Time Zone] on the User Interface screen. Touch [Clock Adjust] on the User Interface screen. hh Special screen appears.
Setup ■■ [Screen transition effect] Select whether to use the screen transition effect when the source control screen is switched to the Home screen. "ON" (Default)/"OFF" NOTE • For how to update the software, see the relevant update procedure manual which comes with the software. Display Setup ÑÑCustomizing the key color You can set the key illumination color. 1 Press the [MENU]/[ ] button. hh Popup menu appears. 2 Touch [SETUP]. hh SETUP screen appears. 3 Touch [Display].
Setup ÑÑChange the wallpaper image or color 1 Touch [Wallpaper Customize] on the Display screen. 2 Select an image. *1 *2 To select wallpaper color Touch [Wallpaper Color] on the Background screen. 2 Select a wallpaper color. You can load an image from the connected USB device and set it as the wallpaper image. Before starting this procedure, it is necessary to connect the device which has the image to load. 1 Touch [User1 Select] or [User2 Select] on the Wallpaper Customize screen.
Setup AV Setup • If you select USB, SD, iPod, DISC (Music CD/ Disc media), Spotify, Pandora or Bluetooth audio as the main source, you cannot select USB, SD or iPod as the AV output source. • If you select Wireless Mirroring, Apple CarPlay or Android Auto as the main source, you cannot select DISC (Music CD/ Disc media), USB, SD or iPod as the AV output source. You can set AV parameters. 1 Press the [MENU]/[ ] button. hh Popup menu appears. 2 Touch [SETUP]. hh SETUP screen appears. 3 Touch [AV].
Controlling Audio Controlling Audio You can adjust various settings such as audio balance or subwoofer level. 1 Press the [MENU]/[ ] button. hh Popup menu appears. 2 Touch [Audio]. 4 Press the button 1 followed by the button 2 for 1 second at the same time. DNX996XR 2 1 DNX696S 2 1 hh Speaker system select screen appears. 5 • • • • • • • • See the following section for each setting. Set up speaker / X’over (P.96) Controlling equalizer (P.98) Set listening position / DTA (P.
Controlling Audio Speaker / X’over setup 1 Press the [MENU]/[ ] button. hh Popup menu appears. 2 Touch [Audio]. hh Audio screen appears. 3 Touch [Speaker / Xʼover]. ■■ [Tweeter] (Only for Front) You can set up the tweeter when you are selecting front speakers. None, Small, Medium, Large ■■ [Xʼover] Display the speaker crossover setup screen. You can adjust the crossover frequency that was set automatically when you selected the speaker type. For details, see Crossover network setup (P.
Controlling Audio 3 Set each parameter as follows. ■■ [HPF FREQ] High Pass Filter adjustment. (When Front or Rear is selected on the Speaker Select screen) ■■ [LPF FREQ] Low Pass Filter adjustment. (When Subwoofer is selected on the Speaker Select screen) ■■ [Slope]*1 Set a crossover slope. ■■ [Gain] Adjust the gain of the front speaker, rear speaker, or subwoofer. ■■ [TW Gain] *2 Adjust the tweeter level.
Controlling Audio Controlling General Audio 1 Press the [MENU]/[ ] button. hh Popup menu appears. 2 Touch [Audio]. hh Audio screen appears. 3 Touch [Fader / Balance]. 4 Equalizer Control You can adjust equalizer by selecting the optimized setting for each category. 1 Press the [MENU]/[ ] button. hh Popup menu appears. 2 Touch [Audio]. hh Audio screen appears. 3 Touch [EQ / SW Level]. 4 Touch the screen and set the Graphic Equalizer as desired. Set each parameter as follows.
Controlling Audio ■■ [SW Level] Adjust the subwoofer volume. This setting is not available when Subwoofer is set to “None”. See Speaker / X’over setup (P.96). ÑÑRecall the EQ curve 1 2 Volume Offset Finely adjust the volume of the current source to minimize the difference in volume between different sources. 1 Press the [MENU]/[ ] button. hh Popup menu appears. 2 Touch [Audio]. hh Audio screen appears. 3 Touch [Volume Offset]. 4 Touch [+] or [-] to adjust the level. Touch [Preset Select].
Controlling Audio Zone Control ■■ [Zone Select] Touch [Single Zone] to turn off the dual zone function. You can select different sources for front and rear positions in the vehicle. 1 Press the [MENU]/[ ] button. hh Popup menu appears. 2 Touch [Audio]. hh Audio screen appears. 3 Touch [Zone Control]. hh Zone Control screen appears. 4 Touch [Zone Select]. 5 Touch [Dual Zone]. ■■ [[Front Source], [Rear Source] Select an audio source for each.
Controlling Audio 3 4 Touch [Sound Effect]. Set each parameter as follows. Listening Position / DTA Listening Position / DTA allows you to improve the sound field depending on the position of the seat you sit. Listening Position / DTA allows you to set “Listening Position” and “Front Focus”. You cannot set both at the same time. 1 Press the [MENU]/[ ] button. hh Popup menu appears. 2 Touch [Audio]. hh Audio screen appears. 3 Touch [Position / DTA].
Controlling Audio 3 4 5 Touch [T] or [U] to adjust the delay time of the selected speaker. ÑÑFront Focus fine adjustment 1 2 3 Touch [Adjust]. Touch [Delay]. Set each parameter as follows. Touch [Level]. Touch [T] or [U] to adjust the sound level of the selected speaker. ■■ [Sound Image LR (Front)] Focus the sound image on the front of front seats. ■■ [Sound Image LR (Rear)] Focus the sound image on the front of rear seats.
Controlling Audio Audio Setup memory Audio Control settings can be memorized. The memorized settings can be recalled at any time. 1 Press the [MENU]/[ ] button. hh Popup menu appears. 2 Touch [Audio]. hh Audio screen appears. 3 Touch [Audio Memory]. ■■ [SETUP Memory] Lock or unlock the Audio SETUP Memory/ Recall/Clear. ■■ [Audio SETUP Memory] Memorize the current audio settings. • Fader / Balance, Speaker / X’over, (User Preset, SW Level), Position / DTA, Sound Effect (P.
Remote control Remote control This unit can be operated using the remote control KNA-RCDV331 (optional accessory). # CAUTION • Put the remote control in a place where it will not move during braking or other operations. A dangerous situation could result, if the remote control falls down and gets wedged under the pedals while driving. • Do not leave the battery near fire or under direct sunlight. A fire, explosion or excessive heat generation may result.
Remote control ■■ DVD Title number/Chapter number ÑÑBasic Operation ■■ VCD 1.X and 2.X (PBC OFF) Track number ■■ VCD 2.X (PBC ON) Scene number/Track number 1 2 3 5 4 ■■ Music CD Track number 6 ■■ Radio (DNX576S / DNR46EX / DNR476S) Frequency value ■■ HD Radio tuner (DNX996XR / DNR876S / DNX696S) Frequency value/Channel number 7 9 11 17 8 10 12 ■■ SiriusXM Channel number 13 2 Enter the number of the content you want to play using the numeric keypad.
Remote control Key Name 9 10 11 106 VOICE VIEW MAP DIR Mode switch Function AUD Displays the control screen of current source. (USB, SD, iPod, DISC) DVD Displays the DVD menu. Turns the playback control on or off while playing VCD. NAV Speaks the voice guidance. AUD, DVD Switches the AV source to be output. NAV Switches between 2D and 3D map displays. AUD, DVD Switches the display angle each time it is pressed.
Connection/Installation Connection/Installation Before Installation Before installation of this unit, please note the following precautions. # WARNINGS • If you connect the ignition wire (red) and the battery wire (yellow) to the car chassis (ground), you may cause a short circuit, that in turn may start a fire. Always connect those wires to the power source running through the fuse box. • Do not cut out the fuse from the ignition wire (red) and the battery wire (yellow).
Connection/Installation In case of DNX996XR/DNR876S 6 (M5 x 8 mm) x6 7 (M5 x 8 mm) Cooling fan • Do not press hard on the panel surface when installing the unit to the vehicle. Otherwise scars, damage, or failure may result. • Reception may drop if there are metal objects near the Bluetooth antenna. x6 8 x1 9 (3.
Connection/Installation 5) Connect the wiring harness connector to the unit. 6) Install the unit in your car. 7) Reconnect the ¤ terminal of the battery. 8) Perform the Initial Setup. See Initial setup (P.10). DNX696S / DNX576S / DNR46EX / DNR476S 8 Installing the unit ÑÑNon-Japanese cars A A : Wide B B : Narrow ●● General Motors cars (DNX996XR) 1) Cut out accessory - to meet the shape of the opening of the center console. 2) Attach accessory - to the unit.
Connection/Installation ÑÑGPS antenna ÑÑMicrophone unit GPS antenna is installed inside of the car. It should be installed as horizontally as possible to allow easy reception of the GPS satellite signals. To mount the GPS antenna inside your vehicle: 1) Clean your dashboard or other surface. 2) Remove the separator of the metal plate (accessory 0). 3) Press the metal plate (accessory 0) down firmly on your dashboard or other mounting surface.
Connection/Installation ÑÑRemoving the trim plate ÑÑRemoving the unit 1) Engage the catch pins on the extraction key (accessory 5) and remove the two locks on the lower level. Lower the trim plate (accessory 8) and pull it forward as shown in the figure. 1) Remove the trim plate by referring to step 1 in "Removing the trim plate". 2) Insert the two extraction key (accessory 5) deeply into the slots on each side, as shown.
Connection/Installation ÑÑConnecting wires to terminals Fuse (15A) Speaker impedance: 4-8 Ω White To front left speaker White/Black Gray To front right speaker Gray/Black Green To rear left speaker Connect to the vehicle’s Accessory 1 parking brake detection switch harness. Light Green PRK SW (Parking sensor wire) (2 m) For best safety, be sure to connect the parking sensor. Green/Black Purple To rear right speaker Purple/Black If no connections are made, do not let the cable come out from the tab.
Connection/Installation ÑÑ3-way speaker system setup ÑÑConnecting the system and external components ●● DNX996XR / DNX696S 12 11 10 9 8 7 6 5 Subwoofer Preout Mid Range Preout Tweeter Preout When connecting to an external amplifier, connect its ground wire to the car’s chassis to avoid damaging the unit. Preout RCA Cable (Sold separately) 1 1 AV Audio output (ø3.
Connection/Installation 7 Dashboard camera interface Connect a Dashboard Camera DRV-N520 (optional accessory). (P.116) 8 Accessory 9: GPS Antenna Use the supplied GPS antenna. Using the GPS antenna other than the supplied one may cause a drop in positioning accuracy.
Connection/Installation ÑÑSecuring the USB extension ●● DNX576S / DNR46EX / DNR476S iPod/iPhone[2] cable KCA-iP103 (0.8m) [3] Secure the USB extension cable with insulating tape or the like so that its connectors are not disconnected. Accessory 2 (Black) (1 m) [4] USB (Black) terminal[1] ÑÑConnecting an iPod/iPhone ●● DNX996XR / DNR876S / DNX696S iPod/iPhone[2] KCA-iP103 (0.8m) [3] Accessory 3 (Gray) (1 m) [4] Accessory 2 (Black) (1 m) [4] iPhone (with Apple CarPlay)[2] KCA-iP103 (0.
Connection/Installation ÑÑConnecting an Android ÑÑConnecting the camera smartphone Left Side View Camera and Right Side View Camera [2] ●● DNX996XR / DNR876S / DNX696S [4] Android smartphone [2] Micro USB to USB cable[2] Front view camera [5] VIDEO input (Yellow) Accessory 3 (Gray) (1 m) [3] Accessory 2 (Black) (1 m) [3] [3] Accessory ~ [6] CA-C3AV [1] Front view camera/Dashboard camera input (Yellow) USB (Gray) terminal[1] USB (Black) terminal[1] Rear view camera [5] Rear view camera input (
Troubleshooting Troubleshooting Problems and Solutions If any trouble occurs, first check the following table for possible problems. NOTE • Some functions of this unit may be disabled by some settings made on this unit. • What might seem to be a malfunction in your unit may just be the result of slight misoperation or miswiring. ÑÑAbout settings • Cannot set up the subwoofer. • Cannot set up subwoofer phase. • No output from the subwoofer. • Cannot set up the low pass filter.
Troubleshooting Disc Error An unplayable disc is inserted. Change the disc. See Playable Media and Files (P.120). Read Error The disc is quite dirty. Clean the disc. See Precautions on handling discs (P.4). Disc is upside down. Load the disc with the labeled side up. Region Code Error The disc you wanted to play has a region code that cannot be played with this unit. See Region Codes in the World (P.122) or try another disc.
Troubleshooting ÑÑApple CarPlay The speed sensor must be connected to use Apple CarPlay wirelessly. Please verify the proper connections or plug in by USB to use Apple CarPlay. The speed pulse is not detected when the Apple CarPlay is started by connecting wirelessly or when the iPhone compatible with wireless Apple CarPlay is registered in [Apple CarPlay Device List]. Check the connection of the speed pulse or plug in over USB to use Apple CarPlay.
Appendix Appendix Playable Media and Files You can play various kinds of media and files on this unit. ÑÑList of playable discs (DNX996XR / DNX696S / DNX576S) Disc types / Standard 120 Support DVD Video DVD Audio DVD-VR DVD-R*1 v × × v DVD-RW DVD+R DVD+RW DVD-R DL (Dual layer) DVD+R DL (Double layer) DVD-RAM CD Music CD*1 CD-ROM CD-R CD-RW DTS-CD Video CD (VCD) Super video CD Photo CD CD-EXTRA HDCD CCCD Others Dualdisc Super audio CD v : Playback is possible. r : Playback is partly possible.
Appendix ÑÑAbout files The following audio and video files are supported. ■■Playable Audio files Format Bit rate Sampling frequency Bit count AAC-LC (.m4a) MPEG-2/MPEG-4 AAC LC HE-AAC(V1,V2) MP3 (.mp3) MPEG-1/MPEG-2 Audio Layer 3 WMA (.wma) Windows Media Audio Standard L3 profile (Version 7,8,9) Linear PCM RIFF waveform Audio (WAVE) (.wav) Format FLAC (.flac) flac 8 – 320kbps, VBR 16 – 48 kHz 16 bit 8 – 320kbps, VBR 16 – 48 kHz 16 bit 8 – 320kbps 16 – 48 kHz 16 bit 16 bit/24 bit Vorbis (.
Appendix Region Codes in the World The DVD players are given a region code according to the country or area it is marketed, as shown in the following map. 1 5 2 6 1 2 3 1 4 5 2 4 ■■DVD disc marks ALL Indicates a region number. The discs with this mark can be played with any DVD player. 8 Indicates the number of audio languages recorded. Up to 8 languages can be recorded in a movie. You can select a favorite language.
Appendix DVD Language Codes Code aa ab af am ar as ay az ba be bg bh bi bn bo br ca co cs cy da de dz el en eo es et eu fa fi fj fo fr fy ga gd gl gn gu ha he hi hr hu hy Language Afar Abkhazian Afrikaans Amharic Arabic Assamese Aymara Azerbaijani Bashkir Byelorussian Bulgarian Bihari Bislama Bengali, Bangla Tibetan Breton Catalan Corsican Czech Welsh Danish German Bhutani Greek English Esperanto Spanish Estonian Basque Persian Finnish Fiji Faroese French Frisian Irish Scots Gaelic Galician Guarani Gujara
Appendix Specifications ■■Monitor section Picture Size DNX996XR : 6.75 inches (diagonal) wide : 152.1 mm (W) × 79.5 mm (H) 5-63/64 × 3-1/8 inch DNR876S : 6.95 inches (diagonal) wide : 156.6 mm (W) × 81.6 mm (H) 6-3/16 × 3-3/16 inch DNX696S / DNX576S / DNR46EX / DNR476S : 6.75 inches (diagonal) wide : 151.8 mm (W) × 79.
Appendix ■■Wireless Mirroring Section (DNX996XR / DNR876S) Mode : Sink Copyright protection : HDCP2.2 Touch Control : UIBC ■■Wi-Fi section (DNX996XR / DNR876S) IEEE Standard : 802.11 a/b/g/n/ac Frequency Range : Dual Band ( 2.4GHz/5GHz ) Channels : Auto(1-11ch)/Auto(149,153,157,161ch) Transfer rates (MAX) : 11a: 54 Mbps / 11b: 11 Mbps / 11g: 54 Mbps / 11n: 300 Mbps / 11ac: 867 Mbps Output Power 2.
Appendix ■■Digital FM tuner section (DNX996XR / DNR876S / DNX696S) Frequency Range (step) : 87.9 MHz – 107.9 MHz (200 kHz) Frequency Response (± 3.
Appendix ■■Navigation section ■■General Receiver DNX996XR / DNR876S : High-sensitivity GNSS receiver DNX696S / DNX576S / DNR46EX / DNR476S : High-sensitivity GPS receiver Operating Voltage : 12V DC car battery Reception Frequency GPS: 1575.42 MHz (C/A code) GLONASS: 1598.0625 MHz – 1605.
Appendix About this Unit ■■Copyrights • The Bluetooth® word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use of such marks by JVC KENWOOD Corporation is under license. Other trademarks and trade names are those of their respective owners. • Manufactured under license from Dolby Laboratories. Dolby, Dolby Audio and the double-D symbol are trademarks of Dolby Laboratories.
Appendix • THIS PRODUCT IS LICENSED UNDER THE VC-1 PATENT PORTFOLIO LICENSE FOR THE PERSONAL AND NONCOMMERCIAL USE OF A CONSUMER TO ( i ) ENCODE VIDEO IN COMPLIANCE WITH THE VC-1 STANDARD (“VC-1 VIDEO”) AND/OR ( ii ) DECODE VC-1 VIDEO THAT WAS ENCODED BY A CONSUMER ENGAGED IN A PERSONAL AND NON-COMMERCIAL ACTIVITY AND/OR WAS OBTAINED FROM A VIDEO PROVIDER LICENSED TO PROVIDE VC-1 VIDEO. NO LICENSE IS GRANTED OR SHALL BE IMPLIED FOR ANY OTHER USE. ADDITIONAL INFORMATION MAY BE OBTAINED FROM MPEG LA, L.L.C.
Appendix ■■FCC WARNING This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made. NOTE • This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Appendix ■■Información acerca de la eliminación de equipos eléctricos y electrónicos al final de la vida útil (aplicable a los países que hayan adoptado sistemas independientes de recogida de residuos) ■■Informação sobre a eliminação de pilhas Los productos con el símbolo de un contenedor con ruedas tachado no podrán ser desechados como residuos domésticos.
DNX996XR DNX696S DNX576S DNR876S DNR46EX DNR476S GPS NAVIGATION SYSTEM INSTRUCTION MANUAL © 2019 JVC KENWOOD Corporation IM399_Nav_K_En_01
© 2019 JVC KENWOOD Corporation All rights reserved. Under the copyright laws, this manual may not be copied, in whole or in part, without the written consent of Garmin. Garmin reserves the right to change or improve its products and to make changes in the content of this manual without obligation to notify any person or organization of such changes or improvements. Go to www.garmin.com for current updates and supplemental information concerning the use of this product.
No Warranty. The Navigation Provider Products are provided to you "as is," and you agree to use them at your own risk.
Data, as further set forth at https://legal.here.com/en-gb/terms /general-content-supplier-terms-and-notices. Term. This Agreement is effective until such time as (i) if applicable, your subscription term is either terminated (by you or by the Navigation Provider) or expires, or (ii) Navigation Provider terminates this Agreement for any reason, including, but not limited to, if the Navigation Provider finds that you have violated any of the terms of this Agreement.
Table of Contents Getting Started................................ 1 Navigation System ................................... 1 Status Bar Icons ...................................... 1 Using the On-Screen Buttons .................. 1 Removing a Shortcut ............................... 1 Adding a Shortcut .................................... 1 Using Multi-touch Controls ...................... 1 Updating the Software ............................. 1 Updating Map Data ..................................
Saving Trip Logs ............................... 10 Viewing Previous Routes and Destinations ........................................... 10 Viewing the Weather Forecast .............. 10 Viewing Weather Near a Different City .................................................... 10 Viewing Road Weather .......................... 10 Finding Fuel Stations and Prices ........... 11 Dynamic Parking ................................... 11 About Traffic.................................
Getting Started WARNING See the Safety Precautions and Important Information in the KENWOOD system instruction manual for product warnings and other important information. NOTE: The screenshots shown in this manual may not exactly match the screens on your navigation system. The images used in this manual are intended for reference only. Navigation System For complete audio system information, see the KENWOOD system instruction manual. • Select to see a menu of options for the current screen.
Finding Locations About Locations The detailed maps loaded in your device contain locations, such as restaurants, hotels, and auto services. You can use categories to browse for nearby businesses and attractions. Finding a Location by Category 1 Select Where To?. 2 Select a category, or select Categories. 3 If necessary, select a subcategory. 4 Select a location. Searching Within a Category To narrow your search results, you can search within some categories. 1 Select Where To?.
Finding an Intersection You can search for an intersection or junction between two streets, highways, or other roads. 1 Select Where To? > Categories > Intersections. 2 Follow the on-screen instructions to enter street information. Select the intersection. 3 Finding a City 1 Select Where To? > Categories > Cities. 2 Select an option: • Select a city from the list of nearby cities. • To search near another location, select Searching near: (Changing the Search Area).
Clearing the List of Recently Found Places Select Where To? > Recent > Clear > Yes. > Finding Parking 1 Select Where To? > Categories > Parking. 2 Select a parking location. Setting a Simulated Location If you are indoors or not receiving satellite signals, you can use the GPS to set a simulated location. 1 Select Settings > Navigation > GPS Simulator. 2 From the main menu, select View Map. 3 Tap the map twice to select an area. The address of the location appears at the bottom of the screen.
4 Select a route. 5 Select Go!. Your Route on the Map NOTICE The speed limit feature is for information only and does not replace your responsibility to abide by all posted speed limit signs and to use safe driving judgment at all times. Garmin and JVC KENWOOD will not be responsible for any traffic fines or citations you receive for failing to follow all applicable traffic laws and signs. The route is marked with a magenta line. A checkered flag marks your destination.
Avoiding Road Features 1 Select Settings > Navigation > Avoidances. 2 Select the road features to avoid on your routes, and select Save. NOTE: When highway avoidances are enabled, long-distance routes may still include highways. • To delete all custom avoidances, select . • To delete one custom avoidance, select the avoidance, and select Delete. > Enabling Advanced Detours Select Settings > Navigation > Advanced Detours.
2 On the USB mass storage device, create a new folder named Garmin. Copy the custom POI files to the Garmin 3 folder on the USB mass storage device. 4 Connect the USB mass storage device to your KENWOOD system. 5 On the KENWOOD system screen, select Yes. 6 Select Custom POIs. 7 Select Install. The KENWOOD system imports the custom points of interest into the system storage. Customizing Map Buttons You can include up to three icons on the right side of the main map.
Viewing the Next Turn While navigating a route, a preview of the next turn, lane change, or other maneuver appears in the upper-left corner of the map. The preview includes the distance to the turn or maneuver and the lane in which you should be traveling, if available. From the map, select to view the next turn on the map. Viewing Traffic Alerts While navigating a route, a traffic alert may appear in the navigation bar. Select the alert to view more information.
specific vehicle and driving habits. You should calibrate when you fill up your fuel tank. 1 Select Apps > ecoRoute™ > At the Pump. 2 Enter the current fuel price. 3 Enter the amount of fuel the vehicle has used since the last time the fuel tank was filled. 4 Enter the distance you have traveled since the last time the fuel tank was filled. 5 Select Next. The device calculates the average vehicle fuel economy. 6 Select Save. Changing the Fuel Price 1 Select Apps > ecoRoute™ > At the Pump.
Scheduling a Trip You can add scheduling information to each location in your trip, including the desired arrival time and layover duration at each location. This can help you plan your departure to reach locations in your trip on time. 1 Select Apps > Trip Planner. 2 Select a trip. 3 Select a location. 4 Select Departure Time or Arrival Time. 5 Select a date and time, and select Save. 6 Select Duration. 7 Select the amount of time you intend to spend at the location, and select Save.
Finding Fuel Stations and Prices Before you can use this feature, your device must be connected using Bluetooth to access connected services. You can find nearby fuel stations and compare fuel prices. 1 Select Apps > Fuel Prices. 2 If necessary, select > Fuel Type, select a fuel type, and select Save. 3 Select a fuel station. Dynamic Parking Before you can use this feature, your device must be connected using Bluetooth to access connected services. This feature is not available in all areas.
Traffic in Your Area Searching for Traffic Delays 1 From the map page, select . 2 Select Traffic Conditions > . 3 Select an item in the list. 4 If there is more than one delay, use the arrows to view additional delays. Viewing a Traffic Incident on the Map 1 From the map, select . 2 Select Traffic Conditions. 3 Select a traffic icon. Understanding Traffic Data The traffic legend explains the icons and colors used on the traffic map. 1 From the map, select > Traffic. 2 Select Traffic Legend.
Display Settings Select Settings > Display. Color Mode: Allows the device to display day or night colors. Changing the Color Mode 1 Select Settings > Display > Color Mode. 2 Select an option: • To use a light background, select Day. • To use a dark background, select Night. • To allow the device to display day or night colors automatically, based on the time of day, select Auto. Traffic Settings From the main menu, select Settings > Traffic. Traffic: Enables traffic.
1 2 3 4 14 Select Settings. If necessary, select a settings category. Select > Restore. Select Yes.
To download free navigation software updates and purchase updated maps for your product, go to www.garmin.com/kenwood.
DNX996XR DNR876S DNX696S DNX576S DNR46EX DNR476S GPS NAVIGATION SYSTEM Quick Start Guide SYSTEME DE NAVIGATION GPS Guide de demarrage rapide SISTEMA DE NAVEGACl6N GPS Guia de inicio rapido JVC KENWOOD Corporation • Updated information (the latest Instruction Manual, system updates, new functions, etc.) is available from . • The Instruction manual is subject to change for modification of specifications and so forth.
Before Use I Contents I Before Use Before Use ............................................. 2 About the Quick start guide About the Quick start guide ................................. 2 How to read this manual........................................ 2 Precautions ................................................................. 2 Safety Precaut ions and Important lnformat ion.............................. 4 • This Quick Start Guide describes basic functions of this unit.
Before Use • You can select a language to display menus, audio file tags, etc. See User Interface Setup (P.90) in the Instruction Manual. • Discs that are not round cannot be used. ® • The Radio Data System or Radio Broadcast Data System feature won't work in areas where the service is not supported by any broadcasting station. • 8-cm (3 inch) discs cannot be used. [i Protecting the monitor • Discs with coloring on the recording surface or discs that are dirty cannot be used.
Before Use Safety Precautions and Important Information Read this information carefully before starting to operate the KENWOOD Car Navigation System and follow the instructions in this manual. Neither KENWOOD nor Garmin shall be liable for problems or accidents resulting from failure to observe the instructions in this manual. A WARNING Failure to avoid the following potentially hazardous situations could result in an accident or collision resulting in death or serious injury.
Bask Operations I Basic Operations Functions of the Buttons on the Front Panel DNX996XR DNR876S English I 5
Basic Operations NOTE • The panels shown in this manual are examples used to provide a clear explanation of operat ions. For this reason, they may be different from the actual panels. f Number [TI m m m m m 6 Name Motion Remote Sensor • Receives the remote control signal. T ,A • Adjusts the volume. The volume will go up to 15 when you keep pressing • · (Volume) NAVIA • Displays the navigation screen. • Pressing and holding turns the screen off.
Basic Operations Motion m Disc insert slot • A slot to insert a disc media. (DNX996XR / DNX696S / DNX576S only) SD card slot • A slot to insert an SD card. • You can play audio/visual files in the card. * 1 • An SD card slot for upgrading the map. For how to upgrade the map, refer to the instruction manual of the navigation system. * 2 *1 If the map update file remains in the SD card, you cannot play audio/visual files. *2 The system of the unit is rebooted after inserting/removing the MAP SD.
Basic Operations Initial Settings (DNX696S / DNX576S / DNR46EX / DNR476S only) Initial setup Perform this setup when you use this unit first time. D Set each item as follows. Initial SETUP United States Language Display Camera OEM SETUP DEMO ■ Locale Select the country for the navigation system. The language, the distance unit, and the gasoline unit are set. CD Touch Locale . (?) Select the desired country. ■ Language Select the language used for the control screen and setting items.
Basic Operations Calendar/clock settings NOTE D Press the MENU 1= button. • Please set the date and time. If they are not set, some functions may not work. ► Popup menu appears. If) Touch Touch screen operations SETUP. -c Str~ri D1~p!ay Off Camera Audio USB AdJU~tmE>nt ► SETUP Menu screen appears. To perform operations on the screen, you need to touch, touch and hold, flick or swipe to select an item, display a setting menu screen or change pages. • Touch D Touch User Interface.
Basic Operations HOME screen descriptions Most functions can be performed from the HOME screen. Widget 0 Press the HOME/,- button. ► HOME screen appears. If) You can change the widget by flicking left or right on the widget area. [I) · Widget - You can change the widget by flicking left or right on the widget area. - Touch the widget to display the detailed screen. (l] · Displays the source selection screen. (P.11) m· Short-cut playback source icons (P.
Basic Operations Popup menu D Press the MENU/=. button. ► Popup menu appears. Source selection screen description You can display icons of all playback sources and options on the source selection screen. f) Touch to display the popup menu. D D -,1 DNX996XR / DNR876S / DNR46EX / ONR476S II II II;~ \\'•r• I•~~ ,,_.,, ,c,,~Q C Spotify Pandora ' ~ X -~, •-• HD Radio SiriusXM Bluetooth ' -' DISC iPod ~ •!C.'\" NAV TEL D D DNX696S / DNX576S [II • Changes playback sources.
Basic Operations II ■ ■ ■ • Switches to the Radio broadcast. DNX576S / DNR46EX / DNR476S only • Switches to the HD Radio broadcast. (P.20) DNX996XR / DNR876S / DNX696S only • Switches to the SiriusXM• satellite radio broadcast. • Plays a Bluetooth audio player. II ■ ■ ■ 1:1 ■ ■ Iii • Plays an iPod/iPhone (P. 18) button. ► HOME screen appears. fl Touch Ill. D Touch STANDBY . ;;., ,,' USB < .,,. .. STAND BY .) • Plays files on a USB device. (P.18) X SD AV-IN ;. ~ Audio :.
Basic Operations Source control screen descriptions There are some functions which can be performed from most screens. Indicators O· D D AM1 Q:QQ Song Tilte 192kHz/24b,t Artist N,1rnc © ► Album Title List screen There are some common function keys in the list screens of most sources. Display the list screen D Touch O.. ► The list screen appears. Category List ... " ··• -._.I r. ~ [I] 1111 All sources icon Displays the source selection screen. (P.
Basic Operations Navigation Operation For details on the navigation function, please refer to the Navigation Instruction Manual. Display the navigation screen 0 • You can get additional information about using the navigation system from Help. To display Help, touch Apps and then touch Help . Press the NAY/ A button. DNX996XR / DNR876S ·{u:::n- I .. DNX696S / DNX576S I DNR46EX / DNR476S I~ L I~ ~ ► The navigation screen appears. ID Touch~. ► Main Menu screen appears.
Basic Operations ■ Viewing the traffic map 09.9''.' '\ •• 'I •• •I $ w) +::, 4:30:·. 24"' D [I] $ •• Do ..~ •• (iD=-= ' ,;,llD •• The traffic map shows color-coded traffic flow and delays on nearby. D $ CD ® II - From the map, touch Touch Traffic Conditions . ■ About traffic 4:07;; D Views the NextTurn page or the junction view page, when available. m m Views the Turn List page. [I] Stops the currents route. III Displays traffic information on the route.
Disc I Disc (DNX996XR, oNX696s, 0Nxs16s) Playing a disc [j Insert a disc DNX996XR 1 DNX696S I DNX576S 1 s;;;;;a = button. ► Popup menu appears. 2 Press the ~ button. l.!)HOM E Press the Touch D. II MENU .J . ~ NAV TEL When removing a disc, pull it horizontally. 15? NOTE 2 Touch DISC EJECT. ► 3 The panel opens. Insert the disc into the slot. • This is not displayed on the popup menu screen of Apple CarPlay or Android Auto source.
Disc Video screen DVD Disc Menu Operation You can set up some functions using the DVDVIDEO disc menu. 1 Touch ► 2 [TI Functi,o n panel marea. Menu Control screen appears. Perform your desired operation as follows. MI-IMIMli'IM Return Touch the left side of the screen to display the function panel. Touch again to close the panel. Enter . Highlight ' a •■ :Stops playback. Touching twice will play the disc from the beginning when you play it next time.
USB/SD/iPod I USB/SD/iPod Connecting a USB device 1 Connect the USB device with the USB cable. (P.33) 2 Touch OPEN to the panel fully opens. 3 Insert the SD card into the slot until it clicks. 4 Press and hold the CAM button. DNX696S I DNX576S I DNR46EX I DNR476S 1 Insert the microSD card into the slot until it clicks. [i Disconnect the use device 1 Press the HOME/~ button. 2 Touch a source other than USB. 3 Detach the USB device.
USB/SD/iPod Connect iPod/iPhone USB/SD/iPod Basic Operation I Preparation 1 Press the HOME/liflll button. • With an Apple CarPlay-capable iPhone, turn off Apple CarPlay by operating the iPhone at functional setup before connecting iPhone. For details of the setup method, contact the manufacturer of the terminal. 2 Touch 3 Touch USB, SD, or iPod. (P.11) • Only one iPod/iPhone can be connected. D lfil. Control screen ..
HD Radio™Tuner/Radio I HD Radio™Tuner/Radio • Q. : Display the Channel List screen. HD Radio Tuner Basic Operation (DNX996XR / DNR876S / DNX696S} · E!J :Display a list of registered bookmarks. · Ill :Displays the Graphic Equalizer screen. (P.25) (!] Preset list To listen to the HD Radio source, touch HD Radio icon on the source selection screen. (P.11) NOTE • HD Radio broadcasting is for North American sales area only. • The screen shot below is for tuner.
HD Radio"" Tuner/Radio Radio Basic Operation (DNX576S / DNR46EX / DNR476S) [II Band buttons Switches bands (between FM and AM). I]] Function panel Touch the left side of the screen to display the function panel. Touch again to close the panel. To listen to the Radio source, touch Radio icon on the source selection screen. (P.11) • Tl (FM only) : Selects the traffic information Control screen ==::::=======! ~ mode. AM 99.9MHz Pre:.etl • PTY (FM only) : Searches for a program by program type.
8/uetooth Control I Bluetooth Control • Input the PIN Code in your smartphone/cell-phone. PIN Code is set to "0000" as the default. Register the Bluetooth device It is necessary to register the Bluetooth audio player or cell-phone in this unit before using the Bluetooth function. 1 •1. 1 8 Select the function you want to use. Touch SETUP. SETUP Menu screen appears. Touch Bluetooth . ► 4 •• (h••l' l'-,.i'"' ► 3 '( Pl~ (rnh• U(l(J/1 Press the MENU/= button. ► Popup menu appears.
8/uetooth Control Using the Hands-Free Unit • Iii: Call using call records • El: Call using the phonebook • D: Call using the preset number You can use the telephone function by connecting the Bluetooth telephone to this unit. • Iii: Call by entering a phone number NOTE • Select the cell-phone to use • If you use the hands-free function frequently, move the TEL short-cut button (icon) to the Home screen. (P.12) When you connect two cell-phones 1) Touch you want t o use.
8/uetooth Control S Select the phone number from the list. [i Operations during a call Phonebook Detail T.alkmg 0123456789 ~ N,1•11,· 1 tL·~,, 0 123456789 jg Narne1 /Office-) 012345678 9 IB ~ ~ N,1,m,1 ((;l•·:~,·.i!) 0 12345678 9 II) DTMF Speech Quality Na-ne i (Other) 0123456789 • Adjust the volume of your voice 1) Touch Speech Quality . NOTE 2) Touch ◄ or ► for Microphone Level . • You can sort the phone numbers in the list by last name or first name.
Controlling Audio I Controlling Audio You can adjust various settings such as audio balance or subwoofer level. 1 2 Press the MENU/= button. [j Equalizer Control You can adjust equalizer by selecting the optimized setting for each category. ► Popup menu appears. 1 Touch EQ / SW Level. Touch Audio. 2 Touch the screen and set the Graphic Equalizer as desired. • Screi>11 D1sp!aJ OFF Aciustment e Camera iC SFlUP USS •••••••••• •.....
Connection/Installation IConnection/Installation Before Installation Before installation of this unit, please note the following precautions. A WARNINGS • If you connect the ignition wire (red) and the battery wire (yellow) to the car chassis (ground), you may cause a short circuit, that in turn may start a fire. Always connect those wires to the power source running through the fuse box. • Do not cut out the fuse from the ignition wire (red) and the battery wire (yellow).
Connection/Installation • Reception may drop if there are metal objects near the Bluetooth antenna.
Connection/Installation DNX696S I DNX576S I DNR46EX I DNR476S Installing the unit [j Non-Japanese cars ~ : Wide Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place. • General Motors cars (DNX996XR) 1) Cut out accessory@ to meet the shape of the opening of the center console. 2) Attach accessory (U) to the unit. [j Japanese cars ®or(J) ~Ca,B,acket @or(J) • Toyota/Scion cars (DNX996XR) NOTE • Make sure that the unit is installed securely in place.
Connection/Installation [j GPS antenna [j Microphone unit GPS antenna is installed inside of the car. It should be installed as horizontally as possible to allow easy reception of the GPS satellite signals. 1) Check the installation position of the microphone (accessory©). To mount the GPS antenna inside your vehicle: 1) Clean your dashboard or other surface. 2) Remove the separator of the metal plate (accessory@)).
Connection/Installation [i Removing the trim plate [i Removing the unit 1) Engage the catch pins on the extraction key (accessory®) and remove the two locks on the lower level. Lower the trim plate (accessory@) and pull it forward as shown in the figure. 1) Remove the trim plate by referring to step 1 in "Removing the trim plate". 2) Insert the two extraction key (accessory@) deeply into the slots on each side, as shown. DNX996XR I DNR876S ,ft , ---~ ® ~ \.
Connection/Installation [j Connecting wires to terminals Fuse (l SA) o□ White Speaker impedance: 4-8 0 (±) ~ 8 _f7..1._j To front left speaker White/Black Gray (±)~ 8_f7..I.__J To front right speaker Gray/Black Green (±)~ 8 _f7..l._j To rear left speaker Connect to the vehicle's Accessory CD parking brake detection switch harness. Light Green ~ (Parking sensor wire) (2 m) For best safety, be sure to connect the parking sensor. Green/Black Purple (±)~ 8 _f7..1.
Connection/Installation [i 3-way speaker system setup e DNX996XR / DNX696S [i Connecting the system and external components ~7===~_p ~ : :c :::;;rr.-:::7=qDJ :.~-~ [!] ~ When connecting to an external amp1 r.er, connect 'ts ground wire to the car's chassis to avoid damaging the unit. ff Precut RCA Cable (Sold separately) m FM/AM antenna input ll~-c:H~ Power amplifier """'- ~ Speaker (optional accessor ) m Input White ~J{(] ~ ..............
Connection/Installation [!) Accessory 9.: GPS Antenna Use the supplied GPS antenna. Using the GPS antenna other than the supplied one may cause a drop in positioning accuracy. /i'----[JJ D [I) [j Connecting an Android smartphone M,cm USB to USB cable'" Accessory 1.1 ': Bluetooth Microphone Accessory 13 (Gray) (1 m) Accessory ( 2 ) (Black) (1 m) ' ~~ 4 ' --""'=-~ ~ :::[l]Jr IIQJ Rear view camera input (Yellow) (TI] Front view camera/Dashboard camera input (Yellow). (P.
Connection/Installation [i Connecting an iPod/iPhone [i Connecting the camera iPod/iPhone12 ==eCJJloD I I3I rrK=C=A=-iP=1=03=(=0.8=m=)= Left Side View Camera and I· Accessory Q) (Gray) (1 m) r411sI Accessory@ (Black) (1 m) 141 \ USB (Gray) terminal 1 ' jsJ ~ ffi Front view camera/Dashboard ~~ USB (Black) terminali' camera input (Yellow) iPhone (with Apple CarPlay)121 131 ~KC=A=-iP=l0=3=(0=.8=m=) = =C[=:JJloD 1·1 1 USB maximum power supply current: DCSV = 1.
Appendix [j To set up the camera assignment settings 1 Press the MENU 1= button. ► Popup menu appears. 2 3 IAppendix Note for specifications Touch SETUP. ■ Bluetooth ► SETUP Menu screen appears. Frequency Touch Camera. ► Camera screen appears. 4 Touch Camera Assignment Settings. 5 Set each item as follows. ■ FRONT VIEW CAMERA / DASH CAM Set the camera assignment from view camera connected to Front view camera/ Dashboard camera input terminal. section : 2.402 - 2.
Appendix ■ Copyrights • The Bluetooth® word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use of such marks by JVC KENWOOD Corporation is under license. Other trademarks and trade names are those of their respective owners. Manufactured under license from Dolby Laboratories. Dolby, Dolby Audio and the double-D symbol are trademarks of Dolby Laboratories. • ~ is a trademark of DVD Format/Logo Licensing Corporation registered in the U.S., Japan and other countries.
Appendix • THIS PRODUCT IS LICENSED UNDER THE VC-1 PATENT PORTFOLIO LICENSE FOR THE PERSONAL AND NONCOMMERCIAL USE OF A CONSUMER TO ( i ) ENCODE VIDEO IN COMPLIANCEWITHTHEVC-1 STANDARD (''VC-1 VIDEO") AND/OR (ii) DECODE VC-1 VIDEO THAT WAS ENCODED BY A CONSUMER ENGAGED IN A PERSONAL AND NON-COMMERCIAL ACTIVITY AND/OR WAS OBTAINED FROM A VIDEO PROVIDER LICENSED TO PROVIDE VC-1 VIDEO. NO LICENSE IS GRANTED OR SHALL BE IMPLIED FOR ANY OTHER USE. ADDITIONAL INFORMATION MAY BE OBTAINED FROM MPEG LA, L.L.C.
r fJ11 Works with _,, Apple CarPlay Made for · • iPhone I iPod android {()) • auto H?) Radio• READY G Spotifye pandora® ave [I] DOLBY AUDIO™ HD2/HD3) Bookmark) Digital Sound) Program Info) VI DE 0 s;;r,™111E™A Bluetooth®Ml Fi J ~c= ~C u KENWOOD \ CERTIFIED Artist Experience) Emergency Alerts)
DNX996XR DNX696S DNX576S DNR876S DNR46EX DNR476S GPS NAVIGATION SYSTEM INSTRUCTION MANUAL © 2019 JVC KENWOOD Corporation IM399_Nav_K_En_01
© 2019 JVC KENWOOD Corporation All rights reserved. Under the copyright laws, this manual may not be copied, in whole or in part, without the written consent of Garmin. Garmin reserves the right to change or improve its products and to make changes in the content of this manual without obligation to notify any person or organization of such changes or improvements. Go to www.garmin.com for current updates and supplemental information concerning the use of this product.
No Warranty. The Navigation Provider Products are provided to you "as is," and you agree to use them at your own risk.
Data, as further set forth at https://legal.here.com/en-gb/terms /general-content-supplier-terms-and-notices. Term. This Agreement is effective until such time as (i) if applicable, your subscription term is either terminated (by you or by the Navigation Provider) or expires, or (ii) Navigation Provider terminates this Agreement for any reason, including, but not limited to, if the Navigation Provider finds that you have violated any of the terms of this Agreement.
Table of Contents Getting Started................................ 1 Navigation System ................................... 1 Status Bar Icons ...................................... 1 Using the On-Screen Buttons .................. 1 Removing a Shortcut ............................... 1 Adding a Shortcut .................................... 1 Using Multi-touch Controls ...................... 1 Updating the Software ............................. 1 Updating Map Data ..................................
Saving Trip Logs ............................... 10 Viewing Previous Routes and Destinations ........................................... 10 Viewing the Weather Forecast .............. 10 Viewing Weather Near a Different City .................................................... 10 Viewing Road Weather .......................... 10 Finding Fuel Stations and Prices ........... 11 Dynamic Parking ................................... 11 About Traffic.................................
Getting Started WARNING See the Safety Precautions and Important Information in the KENWOOD system instruction manual for product warnings and other important information. NOTE: The screenshots shown in this manual may not exactly match the screens on your navigation system. The images used in this manual are intended for reference only. Navigation System For complete audio system information, see the KENWOOD system instruction manual. • Select to see a menu of options for the current screen.
Finding Locations About Locations The detailed maps loaded in your device contain locations, such as restaurants, hotels, and auto services. You can use categories to browse for nearby businesses and attractions. Finding a Location by Category 1 Select Where To?. 2 Select a category, or select Categories. 3 If necessary, select a subcategory. 4 Select a location. Searching Within a Category To narrow your search results, you can search within some categories. 1 Select Where To?.
Finding an Intersection You can search for an intersection or junction between two streets, highways, or other roads. 1 Select Where To? > Categories > Intersections. 2 Follow the on-screen instructions to enter street information. Select the intersection. 3 Finding a City 1 Select Where To? > Categories > Cities. 2 Select an option: • Select a city from the list of nearby cities. • To search near another location, select Searching near: (Changing the Search Area).
Clearing the List of Recently Found Places Select Where To? > Recent > Clear > Yes. > Finding Parking 1 Select Where To? > Categories > Parking. 2 Select a parking location. Setting a Simulated Location If you are indoors or not receiving satellite signals, you can use the GPS to set a simulated location. 1 Select Settings > Navigation > GPS Simulator. 2 From the main menu, select View Map. 3 Tap the map twice to select an area. The address of the location appears at the bottom of the screen.
4 Select a route. 5 Select Go!. Your Route on the Map NOTICE The speed limit feature is for information only and does not replace your responsibility to abide by all posted speed limit signs and to use safe driving judgment at all times. Garmin and JVC KENWOOD will not be responsible for any traffic fines or citations you receive for failing to follow all applicable traffic laws and signs. The route is marked with a magenta line. A checkered flag marks your destination.
Avoiding Road Features 1 Select Settings > Navigation > Avoidances. 2 Select the road features to avoid on your routes, and select Save. NOTE: When highway avoidances are enabled, long-distance routes may still include highways. • To delete all custom avoidances, select . • To delete one custom avoidance, select the avoidance, and select Delete. > Enabling Advanced Detours Select Settings > Navigation > Advanced Detours.
2 On the USB mass storage device, create a new folder named Garmin. Copy the custom POI files to the Garmin 3 folder on the USB mass storage device. 4 Connect the USB mass storage device to your KENWOOD system. 5 On the KENWOOD system screen, select Yes. 6 Select Custom POIs. 7 Select Install. The KENWOOD system imports the custom points of interest into the system storage. Customizing Map Buttons You can include up to three icons on the right side of the main map.
Viewing the Next Turn While navigating a route, a preview of the next turn, lane change, or other maneuver appears in the upper-left corner of the map. The preview includes the distance to the turn or maneuver and the lane in which you should be traveling, if available. From the map, select to view the next turn on the map. Viewing Traffic Alerts While navigating a route, a traffic alert may appear in the navigation bar. Select the alert to view more information.
specific vehicle and driving habits. You should calibrate when you fill up your fuel tank. 1 Select Apps > ecoRoute™ > At the Pump. 2 Enter the current fuel price. 3 Enter the amount of fuel the vehicle has used since the last time the fuel tank was filled. 4 Enter the distance you have traveled since the last time the fuel tank was filled. 5 Select Next. The device calculates the average vehicle fuel economy. 6 Select Save. Changing the Fuel Price 1 Select Apps > ecoRoute™ > At the Pump.
Scheduling a Trip You can add scheduling information to each location in your trip, including the desired arrival time and layover duration at each location. This can help you plan your departure to reach locations in your trip on time. 1 Select Apps > Trip Planner. 2 Select a trip. 3 Select a location. 4 Select Departure Time or Arrival Time. 5 Select a date and time, and select Save. 6 Select Duration. 7 Select the amount of time you intend to spend at the location, and select Save.
Finding Fuel Stations and Prices Before you can use this feature, your device must be connected using Bluetooth to access connected services. You can find nearby fuel stations and compare fuel prices. 1 Select Apps > Fuel Prices. 2 If necessary, select > Fuel Type, select a fuel type, and select Save. 3 Select a fuel station. Dynamic Parking Before you can use this feature, your device must be connected using Bluetooth to access connected services. This feature is not available in all areas.
Traffic in Your Area Searching for Traffic Delays 1 From the map page, select . 2 Select Traffic Conditions > . 3 Select an item in the list. 4 If there is more than one delay, use the arrows to view additional delays. Viewing a Traffic Incident on the Map 1 From the map, select . 2 Select Traffic Conditions. 3 Select a traffic icon. Understanding Traffic Data The traffic legend explains the icons and colors used on the traffic map. 1 From the map, select > Traffic. 2 Select Traffic Legend.
Display Settings Select Settings > Display. Color Mode: Allows the device to display day or night colors. Changing the Color Mode 1 Select Settings > Display > Color Mode. 2 Select an option: • To use a light background, select Day. • To use a dark background, select Night. • To allow the device to display day or night colors automatically, based on the time of day, select Auto. Traffic Settings From the main menu, select Settings > Traffic. Traffic: Enables traffic.
1 2 3 4 14 Select Settings. If necessary, select a settings category. Select > Restore. Select Yes.
To download free navigation software updates and purchase updated maps for your product, go to www.garmin.com/kenwood.
Wireless Apple CarPlay KENv/00D t KENWOOD ' celon i rt g fiJ Phone 9:32 CarPlay I •• •• 9 1• ,1~ - &I • • • • • • • ~ Music Now Playing ... Maps HOME Messages Waze I 1 ' ' I' Google Maps •• .... f NAV <.!) HOME MENU ~= ~ ,~ , [- , ._...... To Enable: Connect phone via Wi-Fi & BT. Once connected, Bluetooth will Automatically Turn Off and Wi-Fi will be used for Wireless Apple CarPlay. Created by the KENWOOD Training Department - KENWOOD University - https://kwu.us.
Wireless Setup Recommended Method~ '"'· ~ ~ I ~ I' ~~ KENIW ~OO@ I Screen Display OFF M iustment ,111 I Camera SETUP KENWOOD X It · · • : ": 0 @ Bluetooth KENWOOD' @ Audio . N~V (.!) HOME Special ~. Bluetooth ~ ~I TEL USB ,.. ~ Audio W sETUP MENU "' ~ r-11n KENWOOo r ~ +;+0 Apple CarPlay Device List -«f D f, Android Auto Device Select 1 1 1 Apple CarPlay Device List ~peech Qualit~j~ AV-OUT Driving Position MENU . C: ~ 11/ /l r N~V .
Wireless Setup ( Settings Settings Bluetooth About Cellular Personal Hotspot General Oo Off Software Update Notifications AirDrop Sounds & Haptics Handoff KENWOOD Are you sure you want to add this BT device ? Passkey 417280 iPhone Do Not Disturb HFP Screen Time A2DP/SPP QJ Hands Free1 --( 0 Hands Free2 ii Accessibility iPhone Storage Background App Refresh Display & Brightness Wallpaper Date & Time Siri & Search DDX6705S DOX6 DDX9704S DOX97- ~ - - . .
Wireless Setup KENv/00D 12:52 I ..... .... It• tit E ., ' ..... I • I• ....... : ~ 12:52 It••••• I KENWOOD ••• LTE ~· CD \\ ii ii f!§ ~ • Music Maps Messages ■ ~ (11 Podcasts Audiobooks Phone Now Playing HOME NAV • l:> HDME MENU 'al: • Created by the KENWOOD Training Department - KENWOOD University - https://kwu.us.jvckenwood.com - JVCKENWOOD USA Corporation follows a policy of continuous advancement in technical development.
Wired (Wireless) Setup Alternate Method! CarPlay Plug in Phone CarPlay \, Allow CarPlay with "DDX9906XR" while phone is locked? Yourcontactsandotherinformation willappearonthiscar'sdisplaywithout unlockingyouriPhone. . ' rPlay Use Wireless CarPlay with "DDX9906XR"? ~arPlayautomatica llyconnectsyour 1Phonetoyourcar'sbuilt•indisplay, andcanacce ss yourphonewhileiti s locked. Enable Wireless CarPlay : . Not Now Allow Use USB Only Leave Plugged in for ~60 Seconds, then Restart =Receiver ..
Wireless Apple CarPlay Requirements The GPS antenna must be connected to use Apple CarPlay wirelessly. Please verify that the GPS antenna is installed, or plug in over USB to use Apple CarPlay. The speed sensor must be connected to use Apple CarPlay wirelessly. Please verify that the speed sensor is installed, or plug in over USB to use Apple CarPlay. 4887 KENv/00D The speed sensor and the GPS antenna must be connected to use Apple CarPlay wirelessly.
KENv/00D Speed Pulse Explanation Our new Wireless Apple CarPlay receivers require a vehicle speed pulse connection in order for Wireless Apple CarPlay to function. ~~ New Accessory: KENWOOD KNA-SPM100 MAP $49.95 Compatible with most 2008+ vehicles. ~ ~ fi.l .. 9:32 . .,.,..-; 9 2 meter cable plugs into OBD2 port Pre-programmed to work automatically. Small interface box footprint. CD I~ .
Receiver Replacement Interfaces Simple 1 Wire Connections 2003-Up GM Class 2 & GM 29-bit LAN Interface This GM2209SR allows you to replace your factory OEM stereo while retaining factory steering wheel con rols, if the • Provides amssorv power (12-volt 10-amp) • Maintain1 the retained accessory power (R.A.P.) feature • Can be uled innon-amplified, or aIlllog/digital amplified model1 • Retain1 warning chimes (GM) , Di,.t~int.tM, Idata link Serial Cable 11m 1;.inn~l did: tl:M\ vehicle is equipped.
MILITARY Units purchased through the U.S.A. military exchange sef'llce overseas may be serviced under warranty in the continental U.S.A., subjoct to the following conditions. 1) The original warranty is ,n effoct 2) P1ool of purchase is provided lo the servicer.
JVCKENWOOD USA Corporation U.S.A. This warranty will be honored only in the U.S.A. WHO IS PROTECTED This warranty is enforceable only by the original purchaser. KENWOOD LIMITED WARRANTY FOR CAR STEREO COMPONENTS WHAT WE WILL PAV FOR We will pay for all labor and material expenses for covered items.