Owner's Manual
Table Of Contents
- Quick Start Guide
- Instruction Manual for Audio Operations (Supplied on CD-ROM)
- Resetting The Unit
- Table of Contents
- Before Use
- How To Read This Manual
- Basic Operations
- DVD/Video CD (VCD) Operation
- CD/Audio And Visual Files/iPod Operation
- Radio, HD Radio tuner and SIRIUS XM Radio Operation
- Radio/HD Radio tuner Basic Operation
- SIRIUS XM Basic Operation
- Memory Operation
- Selecting Operation
- Traffic Information (FM Tuner and HD Radio tuner Only)
- Receive Mode (HD Radio tuner only)
- iTunes Tagging (SIRIUS XM and HD Radio tuner only)
- Content alert (SIRIUS XM only)
- Instant Replay (SIRIUS XM only)
- SIRIUS XM Setup
- Bluetooth Control
- Setting Up
- Controlling Audio
- Remote Controller
- Status Bar Indicator Items
- Troubleshooting
- Error Messages
- Specifications
- Instruction Manual for GPS Navigation (Supplied on CD-ROM)
- Getting Started
- Find It and Go!
- Where To?
- Favorites
- The Main Pages
- Creating and Editing Routes
- Using ecoRoute
- About ecoRoute
- Creating a Vehicle Profile
- Resetting Your Vehicle Profile
- Calibrating Fuel Economy
- Taking the ecoChallenge
- About ecoChallenge Scores
- Hiding Your ecoChallenge Score
- Resetting Your Score
- Viewing Your Fuel Economy
- About the Mileage Report
- Viewing a Mileage Report
- Exporting a Mileage Report
- Setting Routes that Use Less Fuel
- Traffic Information
- Customizing the Settings
- Appendix
- Firmware Update Instructions
- Scan of CD-ROM
Quick
Start Guide
I Installation
Procedure
Before Installation
Before installation
of
this unit,
please
note
the
following
precautions.
~WARNINGS
· If
you
connect the ignition
wire
(red)
and
the battery wire (yellow)
to
the
car
chassis
(ground),
you
may
cause
a
short
circuit,
that
in
turn
may
start
a
fire.
Always
connect those
wires
to
the power
source
running through the
fuse
box.
.
Do
not
cut
out the
fuse
from
the
ignition
wire
(red)
and
the battery
wire
(yellow).
The
power
supply
must
be
connected to
the
wires
via
the
fuse.
~CAUTION
.
Install
this
unit
in
the
console
of
your
vehicle.
Do
not touch the
metal
part of
this
unit
during
and
shortly
after the
use
of the
unit.
Metal
part
such
as
the
heat
sink
and
enclosure
become hot.
NOTES
•
Mounting and wiring this product requires
skills
and experience.
For
best
safety,
leave
the
mounting and wiring work to
professionals.
•
Make sure
to
ground the unit
to
a negative
12V
DC
power
supply.
•
Do
not
install
the
unit
in a spot exposed
to
direct sunlight or excessive heat or
humidity. Also avoid places with
too
much
dust or the possibility
of
water splashing .
•
Do
not
use
your
own
screws.
Use
only
the screws provided.
If
you
use
the wrong
screws, you could damage the unit.
• If
the
power
is
not
turned
ON
("PROTECT'
is
displayed), the speaker wire may have a
short-circuit
or
touched the
chassis
of
the
vehicle and the protection function may
have been activated. Therefore, the speaker
wire should be checked .
• If
your
car's
ignition does
not
have
an
ACC
position, connect
the
ignition wires
to
a
power
source that can be turned on and
off
with
the ignition
key.
If
you connect
the ignition wire
to
a power source
with
a constant voltage supply, such
as
with
battery wires,
the
battery may be drained.
-22-
• If
the console
has
a lid, make sure
to
install
the unit
so
that the faceplate
will
not
hit
the lid when closing and opening .
• If
the fuse blows, first make sure the wires
aren't touching
to
cause a short circuit,
then replace the old fuse with one
with
the
same rating.
• Insulate
unconnected wires
with
vinyl tape
or other similar material.
To
prevent a short
circuit,
do
not
remove the caps on the ends
of
the unconnected wires or the terminals.
• Connect
the speaker wires correctly
to
the
terminals
to
which they correspond. The
unit
may be damaged or fail
to
work
if
you
share the
8
wires or ground
them
to
any
metal part
in
the
car.
•
When only
two
speakers
are
being
connected to the system, connect the
connectors either
to
both the front
output
terminals or
to
both the
rear
output
terminals (do
not
mix front and
rear).
For
example, if you connect the
EB
connector
of
the left speaker
to
a front
output
terminal,
do
not
connect the
8
connector
to
a rear
output
terminal.
•
After the unit
is
installed, check
whether
the
brake lamps, blinkers, wipers, etc. on
the
car
are
working properly.
•
Mount
the unit
so
that the
mounting
angle
is
30°
or
less.
• This unit
has
the cooling fan
(P.27)
to
decrease the internal temperature. Do
not
mount
the unit
in
a place where
the cooling fan
of
the unit
are
blocked .
Blocking these openings will
inhibit
the
cooling
of
the internal temperature and
result
in
malfunction .
•
Do not
press
hard
on the panel surface when
installing the unit to the vehicle. Otherwise
scars,
damage, or failure may
result.
•
Reception may drop if there
are
metal
objects near the Bluetooth antenna.
Bluetooth antenna unit
l•l~~:J.~
1•]~~:~~
1•]~·:~
;;1
lll
II
III
Ill