DPX-U5130BT DPX-U5130 DUAL DIN SIZED CD RECEIVER INSTRUCTION MANUAL © 2012 JVC KENWOOD Corporation 13-2DIN_M_EN_00.
Contents Before use 4 Safety precaution Important information Regulatory Compliance Appendix 5 Trademarks Specifications Basic operations 8 Component names Preparations How to select the item Adjusting the clock General operations Audio adjustments 11 12 Models of iPods/iPhones that can be connected to this unit Playing music Music search Alphabet search Skip search ratio setting Play function APP & iPod Mode Pandora® internet radio Requirements Aha™ Listening to the Aha Radio Basic operations
Hands-free phoning (Function of DPX-U5130BT) 32 Receiving a call Calling a number in the phone book Alphabet search Dialing a number Calling a number in the call log Speed dialing (Preset dial) Registering in the preset dial number list During a call Switching between Two Connected Cell-phones Clearing the disconnection message Making a call by voice dialing Display of phone number types (categories) Bluetooth audio (Function of DPX-U5130BT) 35 Before use Basic operations Play function Bluetooth setti
Before use Safety precaution Important information # WARNING Notes To prevent injuries or a fire, take the following precautions: • Stop the car before operating the unit. • To prevent a short circuit, never put or leave any metallic objects (such as coins or metal tools) inside the unit. ! CAUTION • Adjust the volume so that you can hear the sound outside the car. Driving with the volume too high may cause an accident. • Wipe off the dirt on the panel with a dry silicon or soft cloth.
Appendix Trademarks • The “AAC” logo is a trademark of Dolby Laboratories. • “Made for iPod” and “Made for iPhone” mean that an electronic accessory has been designed to connect specifically to iPod or iPhone, respectively, and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. Please note that the use of this accessory with iPod or iPhone may affect wireless performance.
Appendix Specifications FM tuner section Frequency range 200 kHz space : 87.9 MHz – 107.9 MHz 50 kHz space : 87.5 MHz – 108.0 MHz Usable sensitivity (S/N = 26dB) : 7.2dBf (0.63 μV/75 Ω) Quieting Sensitivity (DIN S/N = 46dB) : 15.2dBf (1.
Audio section Maximum output power : 50 W x 4 Full Bandwidth Power (at less than 1% THD) : 22 W x 4 Speaker Impedance :4–8Ω Tone action Bass : 100 Hz ±8 dB Middle : 1 kHz ±8 dB Treble : 12.5 kHz ±8 dB Preout level/ Load (CD) : 2500 mV/10 kΩ Preout impedance : ≤ 600 Ω Bluetooth section (DPX-U5130BT) General Operating voltage DPX-U5130BT : 14.4 V (10.5 – 16V allowable) DPX-U5130 : 14.4 V (11 – 16V allowable) Maximum Current consumption : 10 A Installation Size (W x H x D) : 182 x 111 x 157 mm Weight : 1.
Basic operations Component names (2) (1) (3) (2) (10) [Control knob] (Volume knob) In the normal mode, turn the knob to adjust the volume or press the knob to turn down the volume quickly. In the Function mode, turn the knob to select an item or press the knob to determine the selection. (11) [E]/ [F] button Press the button to select a song or station. (12) [L] button Press the button to switch between play/pause.
Preparations Exiting the Demonstration mode Turn off the Demonstration mode when you use the unit for the first time after installation. 1 Press the [Control knob] to quit the Demonstration mode when the message “CANCEL DEMO PRESS VOLUME KNOB” appears (approx. 15 seconds). 2 Turn the [Control knob] to select the “YES” and then press the [Control knob]. The Demonstration mode can also be canceled in the Function Setting mode. Refer to (page 28).
Basic operations Adjusting the clock General operations 1 Press and hold the [Control knob]. The hour display blinks. 2 Turn the [Control knob] to adjust the hour, and then press the [Control knob]. The minute display blinks. Power Turn the power on by pressing the [SRC] button. Press and hold [SRC] button to turn the power off. 3 Turn the [Control knob] to adjust the minute, and then press the [Control knob]. Source selection Press the [SRC] button. Pressing the button switches among sources.
Audio adjustments Audio control ( : Factory setting) [1] “USER”: The customized Bass, Middle, and Treble settings are effective. [2] “SUB-W LEVEL”/ “LPF SUBWOOFER”/ “SUB-W PHASE” is selectable only if “SUBWOOFER SET” is set to “ON”. [3] SUB-W LEVEL”/ “SUBWOOFER SET”/ “LPF SUBWOOFER”/ “SUB-W PHASE” is selectable only if “SWITCH PREOUT” is set to “SUB-W”. (DPX-U5130 only : See <“SWITCH PREOUT”> (page 29). [4] “SUB-W PHASE” is selectable only if a setting other than “THROUGH” is selected for “LPF SUB-W”.
Listen to the iPod Models of iPods/iPhones that can be connected to this unit Made for • iPod nano (6th generation) • iPod nano (5th generation) • iPod nano (4th generation) • iPod nano (3rd generation) • iPod nano (2nd generation) • iPod nano (1st generation) • iPod with video • iPod classic • iPod touch (4th generation) • iPod touch (3rd generation) • iPod touch (2nd generation) • iPod touch (1st generation) • iPhone 4S • iPhone 4 • iPhone 3GS • iPhone 3G • iPhone • For information on the compatibility wi
Music search Alphabet search You can search for the song you want to play. You can select an alphabetic character from the list in the browse item (artist, album, etc.) currently selected. 1 2 Press the [1] button. “SEARCH” appears and enters the Music search mode. 1 Press the [1] button. “SEARCH” appears and enters the Music search mode. 2 Press the [1] button. Enter the Alphabet search mode and “SEARCH <_ >” appears. 3 Select a character.
Listen to the iPod Skip search ratio setting APP & iPod Mode You can change the ratio of skip performed as mentioned in (page 13). Allowing you to operate iPod with the control on the iPod. Press the [5] button. 1 Select the iPod source. Refer to (page 10). 2 Press and hold the [AUDIO] button. Enter the Function setting mode. Canceling the APP & iPod mode Press the [5] button. 3 Use the [Control knob] to select “SETTINGS” > “SKIP SEARCH”.
Pandora® internet radio (Function of iPhone®/ Bluetooth device) Requirements Pandora® internet radio Requirements for listening to the Pandora® internet radio are as follows: • In the application on your device, log in and create an account with Pandora. (If you are not already a registered user, an account can also be created at www.pandora.com.) • Internet connection by 3G, LTE, EDGE, or WiFi.
Pandora® internet radio Basic operation Station search Thumbs up You can select the station you want to listen to from your station list. DPX-U5130BT Press and hold the [1] button. 1 Press the [1] button. “SEARCH” appears and enter the Station List mode. 2 Use the [Control knob] to select a sort type. For how to use the [Control knob], refer to (page 9). “A-Z”: Stations are displayed in alphabetical order. “By Date”: Stations are displayed in date order.
New station registration Station preset memory You can search for a desired station. You can register the displayed station as a new station in your station list. You can store a station in the memory. 1 Press and hold the [1] button. “NEW STATION” appears and enter the New station registration. 2 Use the [Control knob] select a search method. For how to use the [Control knob], refer to (page 9).
Aha Radio (Function of iPhone®/ Android) Requirements Aha™ Requirements for listening to Aha™ are as follows: • In the application on your device, log in and create a free account with Aha. • Internet connection by 3G, LTE, EDGE, or WiFi. iPhone or iPod touch • Use an Apple iPhone or iPod touch running iOS4 or later. • Search for “Aha” in the Apple iTunes App Store to find and install the most current version of the Aha™ application on your device.
Basic operations Pause and play a content Press the [L] button. Station search You can select the station you want to listen to from your station list. 1 Press the [1] button. “SEARCH” appears and enter the Station List mode. 2 Backward 15 seconds a content Press and hold the [E] button. Use the [Control knob] to select a station. For how to use the [Control knob], refer to (page 9). 3 Use the [Control knob] to select a content. “Likes” current content Press the [1] button.
Listen to the CD/ Audio file Playing music Playing a disc Insert a disc in the Disc slot. When it is inserted, the source is switched automatically and playback starts. Playing a USB device Connect a USB device to the USB terminal using the CA-U1EX connecter (500 mA Max.: optional accessory). Music search You can select the music you want to listen to from the device or media being played now. 1 Press the [1] button. “SEARCH” appears and enters the Music search mode.
Play function Repeat play Press the [4] button. Switches between Track Repeat (“TRACK REPEAT”) and OFF (“REPEAT OFF”) when pressed while playing a CD. Switches between File Repeat (“FILE REPEAT”), Folder Repeat (“FOLDER REPEAT”), and OFF (“REPEAT OFF”) when pressed while playing an Audio file. Random play Press the [3] button. Randomly plays the music in the disc or folder. When Random Play is turned on, “DISC RANDOM”/ “FOLDER RANDOM” appears. Press this button again cancels the Random play.
Listen to the CD/ Audio file About the USB device About the discs used with this unit • When the USB device is connected to this unit, it is charged when this unit is powered. • Install the USB device in the place where it will not prevent you from driving your vehicle properly. • You cannot connect a USB device via a USB hub or multi card reader. • Save backups of the audio files used with this unit. The files can be erased depending on the operating condition of the USB device.
Listen to the tuner Listening to the radio Selecting a tuner source Press the [SRC] button to select a “TUNER”. Selecting a band Press the [1] button. Pressing the button switches the receiving band (FM1, FM2, FM3, MW, SW1, SW2). Selecting a station Press the [E] or [F] button. The tuning mode can be changed. Refer to (page 23). Station preset memory You can store a station in the memory. 1 Press the [E] or [F] button to select the channel.
Listen to the tuner Direct access tuning (Function of remote control) You can search for a station directly by entering frequency. 1 Press the [DIRECT] button on the remote control. “– – – –” appears and enter the Direct access tuning mode. 2 Press the number buttons on the remote control to enter the frequency. Example: Desired frequency 92.1 MHz (FM) 810 kHz (AM) 3 Press the following buttons [9], [2], [1] [8], [1], [0] Press the [ENT] button on the remote control.
Listen to the AUX Start listening Auxiliary input display setting 1 You can set the display when switched the AUX source. Connect a portable audio player with 3.5 mm stereo mini plug audio cable (commercially available). 2 Select the AUX source. Refer to (page 10). 3 Turn on the portable audio player and start playback. 1 Select the AUX source. Refer to (page 10). 2 Press and hold the [AUDIO] button. Enter the Function setting mode.
Display settings Illumination color selection Display & Illumination setting You can select the illumination color of the panel. You can set the display and illumination. 1 Press and hold the [AUDIO] button. Enter the Function setting mode. 1 Press and hold the [AUDIO] button. Enter the Function setting mode. 2 Use the [Control knob] to select “SETTINGS” > “DISP & KEY” > “COLOR SELECT”. For how to use the [Control knob], refer to (page 9).
4 Use the [Control knob] to select a setting. The previous item appears. Exit the Function setting mode. Press and hold the [6] button.
General settings Muting the audio upon reception of a phone call Demonstration mode setting Function of DPX-U5130 The audio system automatically mutes when it receives an incoming call. 1 Press and hold the [AUDIO] button. Enter the Function setting mode. 2 Use the [Control knob] to select “DEMO MODE”. For how to use the [Control knob], refer to (page 9). 3 Use the [Control knob] to select a setting (“ON” or “OFF”). When a call comes in “CALL” appears.
Initial settings “SP SELECT” You can configure initial settings of this unit. 1 Select the Standby source. Refer to (page 10). 2 Press and hold the [AUDIO] button. Enter the Function setting mode. 3 Use the [Control knob] to select “INITIAL SET”. For how to use the [Control knob], refer to (page 9). 4 Use the [Control knob] to select an Initial setting item.
Registering a Bluetooth (Function of DPX-U5130BT) About the Bluetooth module This unit conforms to the following Bluetooth specifications: Version Bluetooth Ver.2.1+EDR Certified Profile HFP (Hands Free Profile) SPP (Serial Port Profile) PBAP (Phonebook Access Profile) OPP (Object Push Profile) A2DP (Advanced Audio Distribution Profile) AVRCP (Audio/Video Remote Control Profile) For the cell-phones verified for compatibility, access the following URL: http://www.kenwood.
When no device can be selected • If a cell-phone is already selected, deselect it, and then select a different one. • If you cannot select a device using the audio player, connect the device with the audio player. Bluetooth device registration test 1 Press the [Ú] button. “BT MODE” appears and enter the Bluetooth mode. Deleting a registered Bluetooth device 2 Use the [Control knob] to select “BT TEST MODE”. For how to use the [Control knob], refer to (page 9).
Hands-free phoning (Function of DPX-U5130BT) Receiving a call Alphabet search You can search for a name in the phone book by the alphabet. You can answer a phone call Press the [Ú] button. The following operations disconnect the line • Inserting a CD. • Connecting a USB device. Rejecting an incoming call Press the [SRC] button. 1 1 Press the [7] button. 2 Search for a name in the phone book.
Calling a number in the call log 1 Press the [Ú] button. “BT MODE” appears and enter the Bluetooth mode. 2 Use the [Control knob] to select “CALL HISTORY”. For how to use the [Control knob], refer to (page 9). 3 Turn the [Control knob] to select a name and phone number. I : Incoming calls O : Outgoing calls M : Missed calls 4 Press the [Control knob]. Make a call. Speed dialing (Preset dial) 1 Press the [Ú] button. “BT MODE” appears and enter the Bluetooth mode.
Hands-free phoning Switching between Two Connected Cell-phones When two Bluetooth devices are connected, you can assign the Bluetooth device to be used in priority to the other Bluetooth device. When selecting the priority device using the button 1 Press the [Ú] button. “BT MODE” appears and enter the Bluetooth mode. 2 Press and hold [Ú] button. The device given priority is changed. When selecting the priority device from the menu Clearing the disconnection message Press the [Ú] button.
Bluetooth audio (Function of DPX-U5130BT) Before use • You need to register your Bluetooth audio player before using it with this unit. For more details, see (page 30). • You need to select the Bluetooth audio player you wish to connect. Refer to (page 30). Basic operations Selecting a Bluetooth audio source Select the Bluetooth audio source. Refer to (page 10).
Bluetooth settings (Function of DPX-U5130BT) Registering the PIN code Downloading the phone book By operating the Bluetooth device, specify the PIN code necessary for registering this unit. If the phone book is not downloaded automatically to this unit to which a cell-phone -which is not compatible with PBAP- is connected, download it in the following manner: 1 Press the [Ú] button. “BT MODE” appears and enter the Bluetooth mode.
Deleting the phone book Bluetooth detail setting You can delete the phone book stored in this unit to which a cell-phone − which is not compatible with PBAP − is connected. You can configure the initial settings of this unit. 1 2 Press the [7] button. Search for a number/name in the phone book. Operation type Selection of name list and number list Switching to number list Switching to name list 3 4 Press the [Ú] button. “BT MODE” appears and enter the Bluetooth mode.
Basic operation of remote control Before using remote control Basic opreation Preparing the remote control unit VOL Pull the battery sheet out from the remote control unit in the direction of the arrow. Changing the battery of the remote control unit SRC ATT ENT 5/∞ DIRECT/OK AM AUD FM (1) 0—9 (2) Use a commercially available button battery (CR2025). Insert the battery with the + side facing upward, following the illustration inside the case. (1) Keep on sliding. (2) Pull out.
On iPod source • Enter Music search mode: [R]/[S] • Selecting items during Music search mode: [R]/ [S] • Returning to previous item: [6] • Pause/Play: [ENT] On Pandora internet radio source • Song skip: [F] • Pause/Play: [ENT] • Enter the station list mode: [R]/[S] -- Select item: [R]/[S] -- Exit the station list mode: [6] On Aha source • Selecting a content: [E]/[F] • Pause/Play: [ENT] • Enter the station search mode: [R]/[S] -- Select item: [R]/[S] -- Exit the station search mode: [6] Hands-free phone con
Troubleshooting guide Setting error Audio file source Some functions of this unit may be disabled by some settings made on this unit. ö The sound skips when an Audio file is being played. Í The media is scratched or dirty. ò Clean the CD with reference to (page 22). Í The recording condition is bad. ò Play the media again or use another media. ö Cannot set up display. Í The demonstration mode is not turned off as mentioned in (page 28).
Error messages The messages shown below indicates your system condition. ö “PROTECT” (blink) Í The speaker wire has short-circuited or touched the chassis of the vehicle, and then the protection function has been activated. ò Lay or insulate the speaker cable properly and press the Reset button. If “PROTECT” does not disappear, consult your nearest service center. Disc/ USB/ iPod Messages ö “COPY PRO” Í A copy-protected file is played. ö “iPod ERROR” Í Connection to the iPod has failed.
Troubleshooting guide Pandora Messages Aha Messages ö “ADD ERROR” Í Registration of the station has failed. ö “ACTN DISABLED” Í You performed an unavailable operation. ö “CHECK DEVICE” Í Any device ready for Pandora internet radio reception is not connected to this unit. Í Pandora application has not started, you have not signed in, or system maintenance is in progress. ö “AHA APP UPDATE REQUIRED” Í Upgrade the aha application to the latest version. ö “CONNECT ERROR” Í Communication is unstable.
Accessories/ Installation Procedure Installation accessories 1 ..........1 2 ..........1 3 ..........6 4 ..........6 5 ..........2 6 (DPX-U5130BT only) 3 m .....1 Installation Procedure 1 To prevent a short circuit, remove the key from the ignition and disconnect the - battery. ! CAUTION • Mounting and wiring this product requires skills and experience. For safety’s sake, leave the mounting and wiring work to professionals. • Make sure to ground the unit to a negative 12V DC power supply.
Connecting Wires to Terminals Microphone input (DPX-U5130BT only) Microphone (Accessory6) R L Antenna Cord FM/AM antenna input White To front left speaker White/Black Gray To front right speaker Gray/Black Green To rear left speaker Green/Black Purple To rear right speaker Purple/Black Ignition key switch Car fuse box ACC Car fuse box (Main fuse) Red (Ignition wire) Yellow (Battery wire) Black (Ground wire) · (To car chassis) + – Battery 44 | DPX-U5130BT/ DPX-U5130 13-2DIN_M_EN_00.
R L Rear output (DPX-U5130BT only) Front output Sub Woofer output (DPX-U5130BT only) Rear output/ Sub Woofer output (DPX-U5130 only) L Fuse (10A) Wiring harness (Accessory 1) If no connections are made, do not let the wire come out from the tab. Blue/White (Power control wire) P.CONT Blue (Antenna control wire) ANT. CONT Brown (Mute control wire) MUTE When using the optional power amplifier, connect to its power control terminal.
Installation Installing Nissan Cars that uses accessory 3 Installation Install onto the car bracket using the supplied screws (M5 × 8 mm). The holes of the car bracket to use will differ depending on the car model. Accessory 3 (M5 × 8 mm) or Accessory 4 (M5 × 8 mm) Install onto the car bracket using the supplied screws (Accessory 3). Use the mounting holes (¦ in the illustration shown below) that fit the car bracket.
DPX-U5130BT only Installation the Microphone Unit 1 2 3 4 Check the installation position of the microphone (accessory 6). Remove oil and other dirt from the installation surface. Install the microphone. Lay the cable up to the unit with it secured at several positions using tape or the like. ⁄ • Install the microphone as far as possible from the cellphone. Accessory 6 Fix a cable with a commercial item of tape.
13-2DIN_M_EN_00.
