DPX500BT/DPX300U Before reading this manual, click the button below to check the latest edition and the modified pages.
DPX500BT/DPX300U 1. Before use 1-1. Safety precaution 1-1. Safety precaution WARNING To prevent injuries or a fire, take the following precautions: Stop the car before operating the unit. To prevent a short circuit, never put or leave any metallic objects (such as coins or metal tools) inside the unit. CAUTION Adjust the volume so that you can hear the sound outside the car. Driving with the volume too high may cause an accident. Wipe off the dirt on the panel with a dry silicon or soft cloth.
DPX500BT/DPX300U 1. Before use 1-2. Important information 1-2. Important information Condensation When the car is air-conditioned, moisture may collect on the laser lens. This may cause disc read errors. In this case, remove the disc and wait for the moisture to evaporate. How to reset your unit If the unit fails to operate properly, press the Reset button. The unit returns to the factory settings when the Reset button is pressed.
DPX500BT/DPX300U 1. Before use 1-3. Regulatory Compliance 1-3. Regulatory Compliance CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. In compliance with Federal Regulations, following are reproductions of labels on, or inside the product relating to laser product safety. Location : Top plate FCC WARNING This equipment may generate or use radio frequency energy.
The term "IC: " before the certification/ registration number only signifies that the Industry Canada technical specification were met. CAUTION This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65 and RSS-102 of the IC radio frequency (RF) Exposure rules.
(2) este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda causar su operacion no deseada.
DPX500BT/DPX300U 2. Appendix 2-1. Specifications 2-1. Specifications FM tuner section Frequency range (200 kHz step) : 87.9 MHz – 107.9 MHz Usable sensitivity (S/N = 30dB) : 9.3dBf (0.8 μV/75 Ω) Quieting Sensitivity (S/N = 46dB) : 10.2 dBf (1.
File System : FAT12/ 16/ 32 Maximum Supply current : DC 5 V 1A MP3 decode : Compliant with MPEG-1/2 Audio Layer-3 WMA decode : Compliant with Windows Media Audio AAC decode : AAC-LC ".m4a" files WAV decode : Linear-PCM Audio section Maximum output power : 50 W x 4 Full Bandwidth Power (at less than 1% THD) : 22 W x 4 Speaker Impedance :4–8Ω Tone action Bass : 100 Hz ±8 dB Middle : 1 kHz ±8 dB Treble : 12.
DPX500BT : 14.4 V (10.5 – 16V allowable) DPX300U : 14.4 V (11 – 16V allowable) Maximum Current consumption : 10 A Installation Size (W x H x D) : 182 x 111 x 157 mm 7-3/16 x 4-3/8 x 6-1/16 inch Weight : 3.4 lbs (1.5 kg) Specifications subject to change without notice.
DPX500BT/DPX300U 2. Appendix 2-2. Trademarks 2-2. Trademarks The "AAC" logo is a trademark of Dolby Laboratories. "Made for iPod" and "Made for iPhone" mean that an electronic accessory has been designed to connect specifically to iPod or iPhone, respectively, and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards.
Android is a trademark of Google Inc. BlackBerry®, RIM®, Research In Motion® and related trademarks, names and logos are the property of Research In Motion Limited and are registered and/or used in the U.S. and countries around the world. Used under license from Research In Motion Limited.
DPX500BT/DPX300U 3. Basic operations 3-1. Component names 3-1. Component names 1. Disc slot Insert a disc (label side up) in this slot. 2. [1] - [6] button When listening to the radio, press the button to call a registered station. When listening to the CD/USB/iPod, press the button to perform the following operations: [1] [2] : Selecting an audio file folder. [3] : Selecting Random Play. [4] : Selecting Repeat Play. DPX500BT [5] : Selecting App & iPod Control Mode. 3.
. 14. 15. 16. 17. Press the button to switch between play/pause. DPX500BT [7] button Press the button to select the Phone Book. DPX300U [A~Z] button Press the button to enter the alphabet search mode. DPX500BT [Ú] button Press the button to make, answer, or disconnect a hands-free call. DPX300U [iPod] button Press the button to switch to the iPod source. [AUDIO] button Press the button to enter the Audio Control mode.
DPX500BT/DPX300U 3. Basic operations 3-2. Preparations 3-2. Preparations Exiting the Demonstration mode Turn off the Demonstration mode when you use the unit for the first time after installation. 1. Press the [Control knob] to quit the Demonstration mode when the message "CANCEL DEMO PRESS VOLUME KNOB" appears (approx. 15 seconds). 2. Turn the [Control knob] to select the "YES" and then press the [Control knob]. The Demonstration mode can also be canceled in the Function Setting mode. Refer to <13-3.
DPX500BT/DPX300U 3. Basic operations 3-3. How to select the item 3-3. How to select the item For how to select setting items such as a function setting item, see the following example: Example: Adjusting the text scroll of the display 1. Press and hold the [AUDIO] button. "Function" appears and enters the Function setting mode. 2. Select the Text scroll function item Turn the [Control knob] to select "SETTINGS", and then press the [Control knob].
DPX500BT/DPX300U 3. Basic operations 3-4. Adjusting the clock 3-4. Adjusting the clock 1. Press and hold the [Control knob]. The hour display blinks. 2. Turn the [Control knob] to adjust the hour, and then press the [Control knob]. The minute display blinks. 3. Turn the [Control knob] to adjust the minute, and then press the [Control knob].
DPX500BT/DPX300U 3. Basic operations 3-5. General operations 3-5. General operations Power Turn the power on by pressing the [SRC] button. Press and hold [SRC] button to turn the power off. Source selection Press the [SRC]. Pressing the button switches among sources.
DPX500BT/DPX300U 4. Audio adjustments 4-1. Audio control 4-1. Audio control You can adjust the audio control items. 1. Select the source. Refer to . 2. Press the [AUDIO] button. Enter the Audio control mode. 3. Use the [Control knob] to select an audio item. For how to use the [Control knob], refer to <3-3. How to select the item>.
"HPF" High Pass Filter Through/ 100/ 120/ 150 (Hz) "LPF Low Pass Filter SUBWOOFER"[2] 85/ 120/ 160/ Through (Hz) "SUB-W PHASE"[2][3] Subwoofer Phase Reverse (180°)/ Normal (0°) "SUPREME SET"[4] Supreme setting ON/ OFF "VOLUME OFFSET" Volume offset –8 — ±0 (dB) (AUX: -8 — +8) (0) (Colored text: Factory setting) [1] "USER": The customized Bass, Middle, and Treble settings are effective. [2] "SUB-W LEVEL"/ "LPF SUBWOOFER"/ "SUB-W PHASE" is selectable only if "SUBWOOFER SET" is set to "ON".
DPX500BT/DPX300U 5. Listen to the iPod 5-1. Models of iPods/iPhones that can be connected to this unit 5-1.
DPX500BT/DPX300U 5. Listen to the iPod 5-2. Playing music 5-2. Playing music Playing an iPod Connect the iPod to the USB terminal using KCA-iP102 connecter (optional accessory). When it is connected, the source is switched automatically and playback starts. When playback of iPod touch or iPhone does not start If an unsupported application has started when connecting iPod touch or iPhone, "APP&iPod MODE" appears and sometimes playback does not starts.
DPX500BT/DPX300U 5. Listen to the iPod 5-3. Music search 5-3. Music search You can search for the song you want to play. 1. Press the [ ] button. "SEARCH" appears and enters the Music search mode. 2. Search for a song Operation type Operation Selecting items Turn the [Control knob]. Determining selection Press the [Control knob]. Skip Search Press the [ ] or [ Press and hold the [ Returning to previous item Press the [ Returning to Top menu Push the [5] button. ]./ ] or [ ]. ] button.
DPX500BT/DPX300U 5. Listen to the iPod 5-4. Alphabet search 5-4. Alphabet search You can select an alphabetic character from the list in the browse item (artist, album, etc.) currently selected. When DPX300U is used DPX300U allows you to enter the Alphabet search mode by pressing [A to Z] buttons instead of executing the following steps 1 and 2. 1. Press the [ ] button. "SEARCH" appears and enters the Music search mode. 2. Press the [ ] button. Enter the Alphabet search mode and "SEARCH <_ >" appears. 3.
DPX500BT/DPX300U 5. Listen to the iPod 5-5. Skip search ratio setting 5-5. Skip search ratio setting You can change the ratio of skip performed as mentioned in . 1. Select the iPod source. Refer to . 2. Press and hold the [AUDIO] button. Enter the Function setting mode. 3. Use the [Control knob] to select "SETTINGS" > "SKIP SEARCH". For how to use the [Control knob], refer to <3-3. How to select the item>. 4. Use the [Control knob] to select a ratio (0.5, 1, 5, 10).
DPX500BT/DPX300U 5. Listen to the iPod 5-6. Play function 5-6. Play function Repeat play Press the [4] button. Switches between Repeat ("FILE REPEAT") and off ("REPEAT OFF") when pressed. Random play Press the [3] button. Randomly plays the music. Pressing the button toggles the setting between Random play on ("FOLDER RANDOM") and off ("RANDOM OFF"). Press this button again cancels the Random play. All Random play Press and hold the [3] button. All songs in iPod are played at random.
DPX500BT/DPX300U 5. Listen to the iPod 5-7. APP & iPod Mode 5-7. APP & iPod Mode Allowing you to operate iPod with the control on the iPod. DPX500BT Press the [5] button. DPX300U Press and hold the [iPod] button. When the APP & iPod mode is selected, "MODE ON" appears. Canceling the APP & iPod mode DPX500BT Press the [5] button. DPX300U Press the [iPod] button.
DPX500BT/DPX300U 6. Pandora® (Function of iPhone®/ Android™/ BlackBerry®) 6-1. Requirements Pandora® 6-1. Requirements Pandora® Requirements for listening to Pandora® are as follows: A smartphone with the latest Pandora application installed. Latest version of the Pandora application (search App Store for Pandora and install). An active internet connection.
DPX500BT/DPX300U 6. Pandora® (Function of iPhone®/ Android™/ BlackBerry®) 6-2. Listening to Pandora® 6-2. Listening to Pandora® Android or BlackBerry (DPX500BT only) You need to register your cell-phone before using it with this unit. See <14-2. Reg istering a Bluetooth device>. Disconnect the iPhone or iPod touch. 1. Connect the Android/BlackBerry smartphone via Bluetooth. Speakers from which audio is output change depending on the Bluetooth setting "BT HF/AUDIO". The default is Front. See <17-5.
DPX500BT/DPX300U 6. Pandora® (Function of iPhone®/ Android™/ BlackBerry®) 6-3. Basic operation 6-3. Basic operation Thumbs up Press and hold the [1] button. Thumbs down Press and hold the [2] button. Song skip Press the [ ]. Pause and play a song Press the [L] button.
DPX500BT/DPX300U 6. Pandora® (Function of iPhone®/ Android™/ BlackBerry®) 6-4. Station search 6-4. Station search You can select the station you want to listen to from your station list. 1. Press the [ ] button. "SEARCH" appears and enter the Station List mode. 2. Use the [Control knob] to select a sort type. For how to use the [Control knob], refer to <3-3. How to select the item>. "A-Z": Stations are displayed in alphabetical order. "By Date": Stations are displayed in date order. 3.
DPX500BT/DPX300U 6. Pandora® (Function of iPhone®/ Android™/ BlackBerry®) 6-5. New station Creation 6-5. New station Creation You can search for a desired station. You can register the displayed station as a new station in your station list. 1. Press and hold the [ ] button. "NEW STATION" appears and enter the New station registration. 2. Use the [Control knob] select a search method. For how to use the [Control knob], refer to <3-3. How to select the item>.
DPX500BT/DPX300U 6. Pandora® (Function of iPhone®/ Android™/ BlackBerry®) 6-6. Station preset memory 6-6. Station preset memory You can store a station in the memory. 1. Press the [ ] button. "SEARCH" appears and enter the Station List mode. 2. Use the [Control knob] to select a sort type. For how to use the [Control knob], refer to <3-3. How to select the item>. "A-Z": Stations are displayed in alphabetical order. "By Date": Stations are displayed in date order. 3.
DPX500BT/DPX300U 6. Pandora® (Function of iPhone®/ Android™/ BlackBerry®) 6-7. Preset tuning 6-7. Preset tuning Recalling a channel from the memory. Press the button ([3] to [5]) corresponding to the station you want to listen to.
DPX500BT/DPX300U 6. Pandora® (Function of iPhone®/ Android™/ BlackBerry®) 6-8. Pandora source control 6-8. Pandora source control You can turn on/off the Pandora source. 1. Press and hold the [AUDIO] button. Enter the Function setting mode. 2. Use the [Control knob] to select "INITIAL SET" > "PANDORA SRC". For how to use the [Control knob], refer to <3-3. How to select the item>. 3. Use the [Control knob] to select a Pandora source control method. "ON": Turns on the Pandora source.
DPX500BT/DPX300U 7. Aha Radio (Function of iPhone®/ Android) 7-1. Requirements Aha™ 7-1. Requirements Aha™ Requirements for listening to Aha™ are as follows: In the application on your device, log in and create a free account with Aha. Internet connection by 3G, LTE, EDGE, or WiFi. iPhone or iPod touch Use an Apple iPhone or iPod touch running iOS4 or later. Search for "Aha" in the Apple iTunes App Store to find and install the most current version of the Aha™ application on your device.
DPX500BT/DPX300U 7. Aha Radio (Function of iPhone®/ Android) 7-2. Listening to the Aha Radio 7-2. Listening to the Aha Radio Android (DPX500BT only) You need to register your cell-phone before using it with this unit. See <14-2. Reg istering a Bluetooth device>. Disconnect the iPhone or iPod touch. 1. Connect the Android smartphone via Bluetooth. Speakers from which audio is output change depending on the Bluetooth setting "BT HF/AUDIO". The default is Front. See <17-5. Bluetooth detail setting>. 2.
DPX500BT/DPX300U 7. Aha Radio (Function of iPhone®/ Android) 7-3. Basic operations Pause and play a content Press the [L] button. Selecting a content Press the [ ] or [ ] button. Forward 30 seconds a content Press and hold the [ ] button. Backward 15 seconds a content Press and hold the [ ] button. "Likes" current content Press the [1] button. To unvote, press the button again. "Dislikes" current content Press the [2] button. To unvote, press the button again. 7-3.
DPX500BT/DPX300U 7. Aha Radio (Function of iPhone®/ Android) 7-4. Station search 7-4. Station search You can select the station you want to listen to from your station list. 1. Press the [ ] button. "SEARCH" appears and enter the Station List mode. 2. Use the [Control knob] to select a station. For how to use the [Control knob], refer to <3-3. How to select the item>. 3. Use the [Control knob] to select a content.
DPX500BT/DPX300U 7. Aha Radio (Function of iPhone®/ Android) 7-5. Calling a number in the content 7-5. Calling a number in the content You can call the phone number obtained from the content from a smartphone connected to this unit via Bluetooth. 1. Press the [3] button. "MAKE A CALL" appears. 2. Press the [Control knob] to make a call. "CALL" appears. Canceling the confirmative display Press and hold the [ Disconnecting a call Press the [Ú] button. ] button.
DPX500BT/DPX300U 8. iHeartRadio (Function of iPhone®/ Android) 8-1. Requirements iHeartRadio™ 8-1. Requirements iHeartRadio™ Requirements for listening to iHeartRadio are as follows: In the application on your device, log in and create a free account with iHeartRadio. Internet connection by 3G, LTE, EDGE, or WiFi. iPhone or iPod touch Use an Apple iPhone or iPod touch running iOS4 or later.
DPX500BT/DPX300U 8. iHeartRadio (Function of iPhone®/ Android) 8-2. Listening to the iHeartRadio 8-2. Listening to the iHeartRadio Android (DPX500BT only) You need to register your cell-phone before using it with this unit. See <14-2. Reg istering a Bluetooth device>. Disconnect the iPhone or iPod touch. 1. Connect the Android smartphone via Bluetooth. Speakers from which audio is output change depending on the Bluetooth setting "BT HF/AUDIO". The default is Front. See <17-5. Bluetooth detail setting>.
DPX500BT/DPX300U 8. iHeartRadio (Function of iPhone®/ Android) 8-3. Basic operations Stop/Pause and play a song Press the [L] button. Skip track (Custom station) Press the [ ] button. Thumbs up (Custom station) Press the [1] button. Thumbs down (Custom station) Press the [2] button. Adding to favorite stations Press and hold the [5] button. Creating a custom station name Press and hold the [ ] button. Station Scan (Live station) Press the [5] button. 8-3.
DPX500BT/DPX300U 8. iHeartRadio (Function of iPhone®/ Android) 8-4. Station search 8-4. Station search You can select the station you want to listen to from your station list. 1. Press the [ ] button. "SEARCH" appears and enter the Station List mode. 2. Use the [Control knob] to select a category and station. For how to use the [Control knob], refer to <3-3. How to select the item>. When a city list appears, you can skip cities in alphabetical order. Refer to <8-5. Al phabet search>.
DPX500BT/DPX300U 8. iHeartRadio (Function of iPhone®/ Android) 8-5. Alphabet search 8-5. Alphabet search When a city list appears <8-4. Station search>, you can search for a city by alphabet. 1. Press the [ ] button. "SEARCH" appears and enter the Station List mode. 2. Press the [ ] button. Enter the Alphabet search mode and "" appears. 3. Select a character. Operation type Operation Selection of initial Turn the [Control knob].
DPX500BT/DPX300U 8. iHeartRadio (Function of iPhone®/ Android) 8-6. Station delete 8-6. Station delete You can delete a custom or favorite station. 1. Select the iHeartRadio source. Refer to . 2. Press and hold the [AUDIO] button. Enter the Function setting mode. 3. Use the [Control knob] to select "STATION DEL". For how to use the [Control knob], refer to <3-3. How to select the item>. 4. Use the [Control knob] to select a category ("LIVE" or "CUSTOM "). 5.
DPX500BT/DPX300U 9. Listen to the CD/ Audio file 9-1. Playing music 9-1. Playing music Playing a disc Insert a disc in the Disc slot. When it is inserted, the source is switched automatically and playback starts. Playing a USB device Connect a USB device to the USB terminal using CA-U1EX connecter (500 mA Max.: optional accessory). When it is connected, the source is switched automatically and playback starts. Selecting an audio file folder Press the [1] or [2] button.
DPX500BT/DPX300U 9. Listen to the CD/ Audio file 9-2. Music search 9-2. Music search You can select the music you want to listen to from the device or media being played now. 1. Press the [ ] button. "SEARCH" appears and enters the Music search mode. 2. Search for music. Audio file Operation type Operation Selecting folders/files Turn the [Control knob]. Determining selection Press the [Control knob].
DPX500BT/DPX300U 9. Listen to the CD/ Audio file 9-3. Skip search ratio setting 9-3. Skip search ratio setting You can change the ratio of skip performed as mentioned in . 1. Select the USB source. Refer to . 2. Press and hold the [AUDIO] button. Enter the Function setting mode. 3. Use the [Control knob] to select "SETTINGS" > "SKIP SEARCH". For how to use the [Control knob], refer to <3-3. How to select the item>. 4.
DPX500BT/DPX300U 9. Listen to the CD/ Audio file 9-4. Play function 9-4. Play function Repeat play Press the [4] button. Switches between Track Repeat ("TRACK REPEAT") and OFF ("REPEAT OFF") when pressed while playing a CD. Switches between File Repeat ("FILE REPEAT"), Folder Repeat ("FOLDER REPEAT"), and OFF ("REPEAT OFF") when pressed while playing an Audio file. Random play Press the [3] button. Randomly plays the music in the disc or folder.
DPX500BT/DPX300U 9. Listen to the CD/ Audio file 9-5. Direct music search 9-5. Direct music search (Function of remote control) You can search for music by entering the track number. 1. Press the [DIRECT] button on the remote control. "– –" appears and enter the Direct Music search mode. 2. Press the number buttons on the remote control to enter the music number. 3. Press the [ENT] button on the remote control. Canceling the Direct music search mode Press the [ ] button on the remote control.
DPX500BT/DPX300U 9. Listen to the CD/ Audio file 9-6. About the Audio file 9-6. About the Audio file Playable Audio files AAC-LC (.m4a), MP3 (.mp3), WMA (.wma), WAV of USB device (.wav) Playable disc media CD-R/RW/ROM Playable disc file formats ISO 9660 Level 1/2, Joliet, Long file name.
DPX500BT/DPX300U 9. Listen to the CD/ Audio file 9-7. About the USB device 9-7. About the USB device When the USB device is connected to this unit, it is charged when this unit is powered. Install the USB device in the place where it will not prevent you from driving your vehicle properly. You cannot connect a USB device via a USB hub or multi card reader. Save backups of the audio files used with this unit. The files can be erased depending on the operating condition of the USB device.
DPX500BT/DPX300U 9. Listen to the CD/ Audio file 9-8. About "KENWOOD Music Editor Light" and "KENWOOD Music Control" 9-8. About "KENWOOD Music Editor Light" and "KENWOOD Music Control" This unit supports the PC application "KENWOOD Music Editor Light" (hereinafter "KME-Light"), and Android™ application "KENWOOD Music Control" (hereinafter "KMC").
DPX500BT/DPX300U 9. Listen to the CD/ Audio file 9-9. About the discs used with this unit 9-9. About the discs used with this unit This unit can only play the CDs with The following discs cannot be used: . A discs that is not round A discs with coloring on the recording surface or a disc that is dirty A recordable/rewritable disc that has not been finalized (For the finalization process, refer to the instruction manual that came with your disc writing software or your disc recorder.
DPX500BT/DPX300U 9. Listen to the CD/ Audio file 9-10. Handling discs 9-10. Handling discs Do not touch the recording surface of the disc. Do not stick tape etc. on the disc, or use a disc with tape stuck on it. Do not use any accessories for the disc. Do not use any solvents to clean discs. Use a dry silicon or soft cloth. Clean the disc by moving the cloth outward from the center of the disc. When removing a disc from this unit, pull it out horizontally.
DPX500BT/DPX300U 10. Listen to the tuner 10-1. Listening to the radio 10-1. Listening to the radio Selecting a tuner source Press the [SRC] button to select "TUNER". Selecting a band Press the [ ] button. Pressing the button switches the receiving band (FM1, FM2, FM3, AM). Selecting a station Press the [ ] or [ ] button. The tuning mode can be changed. Refer to <10-6. Tuner setting>.
DPX500BT/DPX300U 10. Listen to the tuner 10-2. Station preset memory 10-2. Station preset memory You can store a station in the memory. 1. Press the [ ] or [ ] button to select the station. 2. Press and hold the button ([1] to [6]) to which you want to assign the selected station. "STORED" appears and the station is registered. About the Mix station preset mode In this mode, different bands and tuner sources (Radio, SiriusXM etc.
DPX500BT/DPX300U 10. Listen to the tuner 10-3. Auto memory 10-3. Auto memory You can register 6 stations with good reception automatically. 1. Select the Tuner source. Refer to . 2. Press and hold the [AUDIO] button. Enter the Function setting mode. 3. Use the [Control knob] to select "SETTINGS" > "AUTO MEMORY". For how to use the [Control knob], refer to <3-3. How to select the item>. 4. Use the [Control knob] to select "YES".
DPX500BT/DPX300U 10. Listen to the tuner 10-4. Preset tuning 10-4. Preset tuning Recalling a station from the memory. 1. Press the [ ] button to select a band. 2. Press the button ([1] to [6]) corresponding to the station you want to listen to.
DPX500BT/DPX300U 10. Listen to the tuner 10-5. PTY (Program Type) 10-5. PTY (Program Type) You can search for a station by selecting a Program Type. 1. Press and hold the [AUDIO] button. Enter the Function setting mode. 2. Use the [Control knob] to select "SETTINGS" > "PTY SEARCH". For how to use the [Control knob], refer to <3-3. How to select the item>. 3. Use the [Control knob] to select a Program Type.
Music: Program type indicated by black letters 4. Press the [ ] or [ ] button to select a station. Exit the PTY mode. Press and hold the [ ] button. "NO PTY" display When the selected Program Type is not found, "NO PTY" appears. Select another Program Type. Case where PTY cannot be used This function cannot be used during reception of a traffic bulletin or AM broadcast.
DPX500BT/DPX300U 10. Listen to the tuner 10-6. Tuner setting 10-6. Tuner setting You can set up the tuner. 1. Select the Tuner source. Refer to . 2. Press and hold the [AUDIO] button. Enter the Function setting mode. 3. Use the [Control knob] to select "SETTINGS". For how to use the [Control knob], refer to <3-3. How to select the item>. 4. Use the [Control knob] to select a Tuner setting item. Display Description "SEEK MODE" Sets the tuning mode.
DPX500BT/DPX300U 10. Listen to the tuner 10-7. Direct access tuning 10-7. Direct access tuning (Function of remote control) You can search for a station directly by entering frequency. 1. Press the [DIRECT] button on the remote control. "– – – –" appears and enter the Direct access tuning mode. 2. Press the number buttons on the remote control to enter the frequency. Example: Desired frequency Press the following buttons 92.1 MHz (FM) [9], [2], [1] 810 kHz (AM) [8], [1], [0] 3.
DPX500BT/DPX300U 11. Listen to the AUX 11-1. Start listening 11-1. Start listening 1. Connect a portable audio player with 3.5 mm stereo mini plug audio cable (commercially available). 2. Select the AUX source. Refer to . 3. Turn on the portable audio player and start playback.
DPX500BT/DPX300U 11. Listen to the AUX 11-2. Auxiliary input display setting 11-2. Auxiliary input display setting You can set the display when switched the AUX source. 1. Select the AUX source. Refer to . 2. Press and hold the [AUDIO] button. Enter the Function setting mode. 3. Use the [Control knob] to select "SETTINGS" > "AUX NAME SET". For how to use the [Control knob], refer to <3-3. How to select the item>. 4.
DPX500BT/DPX300U 12. Display settings 12-1. Illumination color selection 12-1. Illumination color selection You can select the illumination color of the panel. 1. Press and hold the [AUDIO] button. Enter the Function setting mode. 2. Use the [Control knob] to select "SETTINGS" > "DISP & KEY" > "COLOR SELECT". For how to use the [Control knob], refer to <3-3. How to select the item>. 3. Use the [Control knob] to select a illumination part. Display Part "ALL" All "DISP" Display "KEY" Button 4.
DPX500BT/DPX300U 12. Display settings 12-2. Adjusting the Illumination color 12-2. Adjusting the Illumination color You can adjust the illumination color of the panel. 1. Select the illumination color you want to adjust. Select from among "COLOR01" to "COLOR24" with reference to <12-1. Illumin ation color selection>. 2. Press and hold the [Control knob]. The RGB value of the selected illumination color appears and enters the Detail color adjustment mode. 3. Set the color.
DPX500BT/DPX300U 12. Display settings 12-3. Display & Illumination setting 12-3. Display & Illumination setting You can set the display and illumination. 1. Press and hold the [AUDIO] button. Enter the Function setting mode. 2. Use the [Control knob] to select "SETTINGS" > "DISP & KEY". For how to use the [Control knob], refer to <3-3. How to select the item>. 3. Use the [Control knob] to select a Display & Illumination setting item.
DPX500BT/DPX300U 12. Display settings 12-4. Text Display Selection 12-4. Text Display Selection You can change the information displayed on each of the following sources: 1. Press the [DISP].
Track title "TRACK TITLE" Play time "P-TIME" Display off "DISP OFF MODE" On Tuner source Information Display Program Service name (FM) "PS" Radio text (FM) "RADIO TEXT" Frequency "FREQUENCY" Display off "DISP OFF MODE" DPX500BT On Bluetooth audio source Information Display Title and Artist name "TITLE/ARTIST" Album and Artist name "ALBUM/ARTIST" Play time "P-TIME" Display off "DISP OFF MODE" On Standby/ Auxiliary input source Information Display Source name "SOURCE NAME" Displ
Information Display Music title "TITLE***" Folder name "FOLDER***" File name "FILE***"
DPX500BT/DPX300U 12. Display settings 12-5. Text scroll Press and hold the [DISP]. The displayed text scrolls. 12-5.
DPX500BT/DPX300U 13. General settings 13-1. Clock setting 13-1. Clock setting 1. Press and hold the [AUDIO] button. Enter the Function setting mode. 2. Use the [Control knob] to select "SETTINGS" > "CLOCK". For how to use the [Control knob], refer to <3-3. How to select the item>. 3. Use the [Control knob] to select a Clock setting item. Display Description "TIME SYNC" Synchronizes this unit's clock with the radio data system station's time data. "ON" / "OFF" (Colored text: Factory setting) 4.
DPX500BT/DPX300U 13. General settings 13-2. Muting the audio upon reception of a phone call 13-2. Muting the audio upon reception of a phone call Function of DPX300U The audio system automatically mutes when it receives an incoming call. When a call comes in "CALL" appears. The audio system pauses. Listening to the audio during a call Press the [SRC] button. The "CALL" display disappears and the audio system comes back ON. When the call ends Hang up the phone.
DPX500BT/DPX300U 13. General settings 13-3. Demonstration mode setting 13-3. Demonstration mode setting You can turn on/off the demonstration mode. 1. Press and hold the [AUDIO] button. Enter the Function setting mode. 2. Use the [Control knob] to select "DEMO MODE". For how to use the [Control knob], refer to <3-3. How to select the item>. 3. Use the [Control knob] to select a setting ("ON" or "OFF"). Exit the Function setting mode. Press and hold the [ ] button.
DPX500BT/DPX300U 13. General settings 13-4. Initial settings 13-4. Initial settings You can configure initial settings of this unit. 1. Select the Standby source. Refer to . 2. Press and hold the [AUDIO] button. Enter the Function setting mode. 3. Use the [Control knob] to select "INITIAL SET". For how to use the [Control knob], refer to <3-3. How to select the item>. 4. Use the [Control knob] to select an Initial setting item.
(Colored text: Factory setting) 5. Use the [Control knob] to select a setting. The previous item appears. Exit the Function setting mode. Press and hold the [ ] button.
DPX500BT/DPX300U 14. Registering a Bluetooth (DPX500BT) 14-1. About the Bluetooth module 14-1. About the Bluetooth module This unit conforms to the following Bluetooth specifications: Version Bluetooth Ver.2.
DPX500BT/DPX300U 14. Registering a Bluetooth (DPX500BT) 14-2. Registering a Bluetooth device 14-2. Registering a Bluetooth device You can register your Bluetooth device in this unit. 1. Start registering a unit by operating the Bluetooth device. By operating the Bluetooth device, register the hands-free unit or audio unit (pairing). Select "DPX5**BT" (for DPX500BT) from the list of found units. 2. If "PAIRING PASS ****** (Bluetooth device name) PRESS VOLUME KNOB" appears, proceed to step 4. 3.
DPX500BT/DPX300U 14. Registering a Bluetooth (DPX500BT) 14-3. Selecting the Bluetooth device you wish to connect 14-3. Selecting the Bluetooth device you wish to connect When two or more Bluetooth devices have already been registered, you need to select the Bluetooth device you wish to use. 1. Press the [Ú] button. "BT MODE" appears and enter the Bluetooth mode. 2.
DPX500BT/DPX300U 14. Registering a Bluetooth (DPX500BT) 14-4. Deleting a registered Bluetooth device 14-4. Deleting a registered Bluetooth device You can delete a registered Bluetooth device. 1. Press the [Ú] button. "BT MODE" appears and enter the Bluetooth mode. 2. Use the [Control knob] to select "SETTINGS" > "PAIRING" > "DEVICE DELETE". For how to use the [Control knob], refer to <3-3. How to select the item>. "(name)" appears. 3. Use the [Control knob] to select an Bluetooth device. 4.
DPX500BT/DPX300U 14. Registering a Bluetooth (DPX500BT) 14-5. Bluetooth device registration test 14-5. Bluetooth device registration test You can check whether a Bluetooth device can be registered by operating this unit. 1. Press the [Ú] button. "BT MODE" appears and enter the Bluetooth mode. 2. Use the [Control knob] to select "BT TEST MODE". For how to use the [Control knob], refer to <3-3. How to select the item>. "PLEASE PAIR YOUR PHONE" appears. 3.
DPX500BT/DPX300U 15. Hands-free phoning (DPX500BT) 15-1. Receiving a call You can answer a phone call Press the [Ú] button. The following operations disconnect the line Inserting a CD. Connecting a USB device. Rejecting an incoming call Press the [SRC] button. 15-1.
DPX500BT/DPX300U 15. Hands-free phoning (DPX500BT) 15-2. Calling a number in the phone book 15-2. Calling a number in the phone book 1. Press the [7] button. 2. Search for a name in the phone book. Operation type Operation Selection of name list Turn the [Control knob]. Switching to number list Press the [Control knob]. 3. Search for a number in the phone book. Operation type Operation Selection of number list Turn the [Control knob]. Switching to name list Press the [ ]. 4.
DPX500BT/DPX300U 15. Hands-free phoning (DPX500BT) 15-3. Alphabet search 15-3. Alphabet search You can search for a name in the phone book by the alphabet. 1. Press the [7] button. 2. Press the [ ] button. Enter the Alphabet search mode and "" appears. 3. Search for a name in the phone book. Operation type Operation Selection of initial Turn the [Control knob]. Page feeding of alphabetical list Press the [ Determine the initial Press the [Control knob]. ] or [ 4.
DPX500BT/DPX300U 15. Hands-free phoning (DPX500BT) 15-4. Dialing a number 15-4. Dialing a number 1. Press the [Ú] button. "BT MODE" appears and enter the Bluetooth mode. 2. Use the [Control knob] to select "NUMBER DIAL". For how to use the [Control knob], refer to <3-3. How to select the item>. 3. Enter a phone number. Operation type Operation Selection of number Turn the [Control knob]. Selection of digit Press the [ 4. Press the [Control knob]. Make a call.
DPX500BT/DPX300U 15. Hands-free phoning (DPX500BT) 15-5. Calling a number in the call log 15-5. Calling a number in the call log 1. Press the [Ú] button. "BT MODE" appears and enter the Bluetooth mode. 2. Use the [Control knob] to select "CALL HISTORY". For how to use the [Control knob], refer to <3-3. How to select the item>. 3. Turn the [Control knob] to select a name and phone number. I : Incoming calls O : Outgoing calls M : Missed calls 4. Press the [Control knob]. Make a call.
DPX500BT/DPX300U 15. Hands-free phoning (DPX500BT) 15-6. Speed dialing (Preset dial) 15-6. Speed dialing (Preset dial) 1. Press the [Ú] button. "BT MODE" appears and enter the Bluetooth mode. 2. Press number button ([1] to [6]). 3. Press the [Control knob]. Make a call. Registering a dial number You need to register the preset dial number. Refer to <15-7. Registering in the p reset dial number list>.
DPX500BT/DPX300U 15. Hands-free phoning (DPX500BT) 15-7. Registering in the preset dial number list 15-7. Registering in the preset dial number list 1. Press the [Ú] button. "BT MODE" appears and enter the Bluetooth mode. 2. Enter the phone number you wish to register. Enter the phone number with reference to the following: <15-2. Calling a number in the phone book> <15-4. Dialing a number> <15-5. Calling a number in the call log> 3. Press and hold number button ([1] to [6]).
DPX500BT/DPX300U 15. Hands-free phoning (DPX500BT) 15-8. During a call 15-8. During a call Disconnecting a call Press the [SRC] button. Switching to the Private mode Press the [L] button. Pressing this knob each time switches between the private talk mode ("PV TALK") and hands-free talk mode ("HF TALK").
DPX500BT/DPX300U 15. Hands-free phoning (DPX500BT) 15-9. Switching between two connected cell-phones 15-9. Switching between two connected cell-phones When two Bluetooth devices are connected, you can assign the Bluetooth device to be used in priority to the other Bluetooth device. When selecting the priority device using the button 1. Press the [Ú] button. "BT MODE" appears and enter the Bluetooth mode. 2. Press and hold [Ú] button. The device given priority is changed.
DPX500BT/DPX300U 15. Hands-free phoning (DPX500BT) 15-10. Clearing the disconnection message 15-10. Clearing the disconnection message Press the [Ú] button. "HF DISCONCT" disappears.
DPX500BT/DPX300U 15. Hands-free phoning (DPX500BT) 15-11. Making a call by voice dialing 15-11. Making a call by voice dialing You can make a voice call using the voice recognition function of the cell-phone. 1. Press and hold the [Ú] button to start voice recognize. "VOICE CONTROL" appears. 2. Pronounce the name registered in the cell-phone. Make a call. Canceling the voice recognize Press and hold the [Ú] button.
DPX500BT/DPX300U 15. Hands-free phoning (DPX500BT) 15-12. Display of phone number types (categories) 15-12.
DPX500BT/DPX300U 16. Bluetooth audio (DPX500BT) 16-1. Before use 16-1. Before use You need to register your Bluetooth audio player before using it with this unit. For more details, see <14-2. Registering a Bluetooth device>. You need to select the Bluetooth audio player you wish to connect. Refer to <14-3. Selecting the Bluetooth device you wish to connect>.
DPX500BT/DPX300U 16. Bluetooth audio (DPX500BT) 16-2. Basic operations 16-2. Basic operations Selecting a Bluetooth audio source Press the [SRC] button. Pause and play a song Press the [L] button. Selecting a song Press the [ ] or [ ] button. Fast-forwarding or fast-backwarding a song Press and hold the [ ] or [ ] button. Selecting an audio file folder Press the [1] or [2] button.
DPX500BT/DPX300U 16. Bluetooth audio (DPX500BT) 16-3. Play function 16-3. Play function Random play Press the [3] button. Switches between Folder Random ("FOLDER RANDOM"), All Random ("ALL RANDOM"), and OFF ("RANDOM OFF"). Repeat play Press the [4] button. Switches between File Repeat ("FILE REPEAT"), All Repeat ("ALL REPEAT"), and OFF ("REPEAT OFF"). Functions that can be used The available playback functions differ depending on the type of the connected Bluetooth audio player.
DPX500BT/DPX300U 17. Bluetooth settings (DPX500BT) 17-1. Registering the PIN code 17-1. Registering the PIN code By operating the Bluetooth device, specify the PIN code necessary for registering this unit. 1. Press the [Ú] button. "BT MODE" appears and enter the Bluetooth mode. 2. Use the [Control knob] to select "SETTINGS" > "DETAILED SET" > "PIN CODE EDIT". For how to use the [Control knob], refer to <3-3. How to select the item>. 3.
DPX500BT/DPX300U 17. Bluetooth settings (DPX500BT) 17-2. Downloading the phone book 17-2. Downloading the phone book If the phone book is not downloaded automatically to this unit to which a cell-phone which is not compatible with PBAP- is connected, download it in the following manner: 1. Press the [Ú] button. "BT MODE" appears and enter the Bluetooth mode. 2. Use the [Control knob] to select "SETTINGS" > "TRANSFER PB". For how to use the [Control knob], refer to <3-3. How to select the item>.
DPX500BT/DPX300U 17. Bluetooth settings (DPX500BT) 17-3. Deleting the phone book 17-3. Deleting the phone book You can delete the phone book stored in this unit to which a cell-phone − which is not compatible with PBAP − is connected. 1. Press the [7] button. 2. Search for a number/name in the phone book. Operation type Operation Selection of name list and number list Turn the [Control knob]. Switching to number list Press the [Control knob]. Switching to name list Press the [ ]. 3.
DPX500BT/DPX300U 17. Bluetooth settings (DPX500BT) 17-4. Displaying the firmware version 17-4. Displaying the firmware version You can view the version of the firmware of this unit. 1. Press the [Ú] button. "BT MODE" appears and enter the Bluetooth mode. 2. Use the [Control knob] to select "SETTINGS" > "DETAILED SET" > "BT F/W UPDATE". For how to use the [Control knob], refer to <3-3. How to select the item>. The firmware version appears. Exit the Bluetooth mode. Press the [Ú] button.
DPX500BT/DPX300U 17. Bluetooth settings (DPX500BT) 17-5. Bluetooth detail setting 17-5. Bluetooth detail setting You can configure the initial settings of this unit. 1. Press the [Ú] button. "BT MODE" appears and enter the Bluetooth mode. 2. Use the [Control knob] to select "SETTINGS" > "DETAILED SET". For how to use the [Control knob], refer to <3-3. How to select the item>. 3. Use the [Control knob] to select an Bluetooth detail setting item.
DPX500BT/DPX300U 18. SiriusXM™ Satellite Radio (optional tuner and service required) 18-1. Before use 18-1. Before use SiriusXM Satellite Radio operation requires the connection of the optional SiriusXM Connect Vehicle Tuner. To activate the SiriusXM Vehicle Connect tuner, you will need the Radio ID. Make a note of your Radio ID For each SiriusXM Vehicle Connect tuner, peculiar Radio ID is assigned. To confirm your Radio ID, tune to channel 0. The letters I, O, S and F are not used in any Radio ID.
DPX500BT/DPX300U 18. SiriusXM™ Satellite Radio (optional tuner and service required) 18-2. Listening to the SiriusXM™ Satellite Radio 18-2. Listening to the SiriusXM™ Satellite Radio Selecting a tuner source Press the [SRC] button to select "SIRIUS XM". Selecting a band Press the [ ] button. Pressing the button switches the receiving band (SXM1, SXM2, SXM3, SXM4). Selecting a channel Press the [ ] or [ ] button. The tuning mode can be changed. Refer to <18-15. SiriusXM tuner setting>.
DPX500BT/DPX300U 18. SiriusXM™ Satellite Radio (optional tuner and service required) 18-3. Category and channel search 18-3. Category and channel search You can select the channel and category you want to receive. 1. Press and hold the [ ] button. "CAT SEARCH" appears and enter the Category and Channel search mode. 2. Use the [Control knob] to select a category. For how to use the [Control knob], refer to <3-3. How to select the item>. 3. Use the [Control knob] to select a channel.
DPX500BT/DPX300U 18. SiriusXM™ Satellite Radio (optional tuner and service required) 18-4. Channel preset memory 18-4. Channel preset memory You can store a channel in the memory. 1. Press the [ ] or [ ] button to select the channel. 2. Press and hold the button ([1] to [6]) to which you want to assign the selected channel. "STORED" appears and the channel is registered. About the Mix Station present mode In this mode, different bands and tuner sources (Radio, SiriusXM etc.
DPX500BT/DPX300U 18. SiriusXM™ Satellite Radio (optional tuner and service required) 18-5. Preset tuning 18-5. Preset tuning Recalling a channel from the memory. 1. Press the [ ] button to select a band. 2. Press the button ([1] to [6]) corresponding to the channel you want to listen to.
DPX500BT/DPX300U 18. SiriusXM™ Satellite Radio (optional tuner and service required) 18-6. Direct access tuning 18-6. Direct access tuning (Function of remote control) You can search for a channel directly by entering its number. 1. Press the [DIRECT] button on the remote control. 2. Press the number buttons on the remote control to enter a channel number. 3. Press the [ENT] button on the remote control. Canceling the Direct access tuning mode Press the [ ] button on the remote control.
DPX500BT/DPX300U 18. SiriusXM™ Satellite Radio (optional tuner and service required) 18-7. iTunes tagging 18-7. iTunes tagging You can store the tag of the information about the song being received, and send it to the connected iPod. You can easily find the song on the iTunes Store according to the tag sent to the iPod. 1. Press and hold the [ ] button. " " will be indicated on the display when song information can be registered.
DPX500BT/DPX300U 18. SiriusXM™ Satellite Radio (optional tuner and service required) 18-8. Parental Lock setting 18-8. Parental Lock setting You can turn on/off Parental Lock for each channel. 1. Select the SiriusXM Radio source. Refer to . 2. Press and hold the [AUDIO] button. Enter the Function setting mode. 3. Use the [Control knob] to select "SETTINGS" > "CHANNEL LOCK". For how to use the [Control knob], refer to <3-3. How to select the item>. 4. Enter the pass code.
DPX500BT/DPX300U 18. SiriusXM™ Satellite Radio (optional tuner and service required) 18-9. Clearing the Parental Lock setting 18-9. Clearing the Parental Lock setting You can clear the Parent Lock setting for each channel. 1. Select the SiriusXM Radio source. Refer to . 2. Press and hold the [AUDIO] button. Enter the Function setting mode. 3. Use the [Control knob] to select "SETTINGS" > "CHANNEL LOCK". For how to use the [Control knob], refer to <3-3. How to select the item>. 4.
DPX500BT/DPX300U 18. SiriusXM™ Satellite Radio (optional tuner and service required) 18-10. Setting Parental Lock for Mature content 18-10. Setting Parental Lock for Mature content You can turn on/off Parental Lock for the adult channels assigned by SiriusXM. 1. Select the SiriusXM Radio source. Refer to . 2. Press and hold the [AUDIO] button. Enter the Function setting mode. 3. Use the [Control knob] to select "SETTINGS" > "CHANNEL LOCK".
DPX500BT/DPX300U 18. SiriusXM™ Satellite Radio (optional tuner and service required) 18-11. Parental Lock pass code setting 18-11. Parental Lock pass code setting You can set a new pass code for Parental Lock setting. 1. Select the SiriusXM Radio source. Refer to . 2. Press and hold the [AUDIO] button. Enter the Function setting mode. 3. Use the [Control knob] to select "SETTINGS" > "CHANNEL LOCK". For how to use the [Control knob], refer to <3-3. How to select the item>. 4.
DPX500BT/DPX300U 18. SiriusXM™ Satellite Radio (optional tuner and service required) 18-12. SiriusXM Replay™ 18-12. SiriusXM Replay™ You can replay up to the last 60 minutes broadcasting of current channel. 1. Press the [L] button. "REPLAY MODE" appears. The "+" indicator stays lit during Replay. The songs are replayed starting with the song played 60 minutes ago. During Replay, you can perform the following operations: Operation type Operation Pause and play Press the [L].
DPX500BT/DPX300U 18. SiriusXM™ Satellite Radio (optional tuner and service required) 18-13. Channel skip setting 18-13. Channel skip setting You can register the channel you wish to skip. 1. Select the SiriusXM Radio source. Refer to . 2. Press and hold the [AUDIO] button. Enter the Function setting mode. 3. Use the [Control knob] to select "SETTINGS" > "CHANNEL SKIP" > "CHANNEL EDIT". For how to use the [Control knob], refer to <3-3. How to select the item>. 4.
DPX500BT/DPX300U 18. SiriusXM™ Satellite Radio (optional tuner and service required) 18-14. Clearing the channel skip setting 18-14. Clearing the channel skip setting You can clear the skip setting for all the selected channels together. 1. Select the SiriusXM Radio source. Refer to . 2. Press and hold the [AUDIO] button. Enter the Function setting mode. 3. Use the [Control knob] to select "SETTINGS" > "CHANNEL SKIP" > "CHANNEL CLEAR". For how to use the [Control knob], refer to <3-3.
DPX500BT/DPX300U 18. SiriusXM™ Satellite Radio (optional tuner and service required) 18-15. SiriusXM tuner setting 18-15. SiriusXM tuner setting You can set the SiriusXM tuner related items. 1. Press the [Control knob]. Enter the Function setting mode. 2. Use the [Control knob] to select "SETTINGS". For how to use the [Control knob], refer to <3-3. How to select the item>. 3. Use the [Control knob] to select an SiriusXM tuner setting item. Display Description "SEEK MODE" Sets the tuning mode.
DPX500BT/DPX300U 19. Basic operation of remote control 19-1. Before using remote control 19-1. Before using remote control Preparing the remote control unit Pull the battery sheet out from the remote control unit in the direction of the arrow. Changing the battery of the remote control unit Use a commercially available button battery (CR2025). Insert the battery with the + side facing upward, following the illustration inside the case. 1. Keep on sliding. 2. Pull out.
DPX500BT/DPX300U 19. Basic operation of remote control 19-2. Basic opreation 19-2. Basic opreation General control Volume control: [VOL] Source selection: [SRC] Press and hold to turn off the power. Volume reduction: [ATT] When the button is pressed again, the volume returns to the previous level. Returning to previous item: [ ] Selection of item: [ ]/[ ] Determination: [ENT] Enter Audio Control mode: [AUD] About power on The remote control cannot be used to turn the power on.
Enter the Music search mode: [ ]/[ ] Selecting folders/files during Music search mode: [ Returning to previous folder: [ ] ]/[ On iPod source Enter Music search mode: [ ]/[ ] Selecting items during Music search mode: [ Returning to previous item: [ ] Pause/Play: [ENT] On Pandora source Song skip: [ ] Pause/Play: [ENT] Enter the station list mode: [ ]/[ Select item: [ ]/[ ] Exit the station list mode: [ ] ] On Aha source Selecting a content: [ ]/[ Pause/Play: [ENT] Enter the station search mode: [ ]
Answer the call: [Ú] During a call End the call: [ ]
DPX500BT/DPX300U 20. Troubleshooting guide 20-1. Setting error 20-1. Setting error Some functions of this unit may be disabled by some settings made on this unit. Cannot set up display. The demonstration mode is not turned off as mentioned in <13-3. Demonstration mode setting>. Cannot set up the subwoofer. Cannot set up the low pass filter. No output from the subwoofer. "SUBWOOFER SET" is not set to ON as mentioned in <4-1. Audio control>. Cannot set up the subwoofer phase.
DPX500BT/DPX300U 20. Troubleshooting guide 20-2. Operation/wiring error 20-2. Operation/wiring error What might seem to be a malfunction in your unit may just be the result of a slight operation error or a wiring error. Before calling for service, first check the following table for possible problems. General The key beep does not sound The Preout jack is in use. The key beep cannot be output from the Preout jack. Sound cannot be heard. Adjust the volume to the optimum level.
No beep is heard depending on the type of your cell-phone. The "CALL BEEP" of <17-5. Bluetooth detail setting> is set ON. Voice is not recognized. The vehicle window is open. If the surrounding noise is large, voice cannot be recognized properly. Close the vehicle windows to reduce noise. Small voice. If voice is too small, it cannot be recognized properly. Speak into the microphone a little more loudly and naturally. The sound from the Bluetooth audio player is discontinuous.
DPX500BT/DPX300U 20. Troubleshooting guide 20-3. Error messages 20-3. Error messages The messages shown below indicates your system condition. General "PROTECT" (blink) The speaker wire has short-circuited or touched the chassis of the vehicle, and then the protection function has been activated. Lay or insulate the speaker cable properly and press the Reset button. If "PROTECT" does not disappear, consult your nearest service center. Disc/ USB/ iPod Messages "COPY PRO" A copy-protected file is played.
is repeated, use another USB device. Bluetooth Messages "AUD DISCONCT" The unit cannot communicate with the Bluetooth audio player. "DEVICE FULL" 5 Bluetooth device have already been registered. No more Bluetooth devices are registered. "HF DISCONCT" The unit cannot communicate with the cell-phone. "HF ERROR 68" The unit cannot communicate with the cell-phone. Cycle the power switch. If this message still appears, press the Reset button on the control unit. "HF ERROR 89" Update of the firmware has failed.
"NO STATIONS" There is no receivable station. "NOT EXIST" The registered station has been deleted or the device is not the registered one. "RATING ERROR" Registration of Thumbs Up/Down has failed. "SEARCH ERROR" No station could be searched for. "STATION LIMT" The number of registered stations has reached the upper limit. Retry after deleting an unnecessary station. "UPGRADE APP" The Pandora application is an older version which the unit can not support.
"CHECK APP" Log in to aha. "CHECK DEVICE" Aha application has not started, you have not signed in, or system maintenance is in progress. "CONNECT PHONE" Connect the cell-phone. "LOGIN FAILED" Logging in to aha has failed. "NETWORK UNAVAILABLE" The network has been disconnected. "NO CONTENT" There is no receivable content. "POOR GPS" The GPS reception condition of your smartphone is poor. SiriusXM Advisory Messages "CH UNAVAIL" The currently selected channel is unavailable.
