DPX792BH DPX702BH DPX592BT DPX502BT DUAL DIN SIZED CD RECEIVER INSTRUCTION MANUAL RECEPTEUR CD FORMAT DUAL DIN MODE D’EMPLOI RECEPTOR DUAL DE CD TAMAÑO DIN MANUAL DE INSTRUCCIONES For your records Record the serial number, found on the back of the unit, in the spaces designated on the warranty card, and in the space provided below. Refer to the model and serial numbers whenever you call upon your Kenwood dealer for information or service on the product.
CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. In compliance with Federal Regulations, following are reproductions of labels on, or inside the product relating to laser product safety. JVC KENWOOD Corporation 2967-3, ISHIKAWA-MACHI, HACHIOJI-SHI, TOKYO, JAPAN THIS PRODUCT COMPLIES WITH DHHS RULES 21CFR SUBCHAPTER J IN EFFECT AT DATE OF MANUFACTURE.
IC (Industry Canada) Notice This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. The term “IC: ” before the certification/ registration number only signifies that the Industry Canada technical specification were met.
SOFTWARE LICENSE AGREEMENT The software embedded in the Product (hereinafter the "Licensed Software") provided by Licensor is copyrighted to or sublicensable by the Licensor, and this Agreement provides for the terms and conditions which Users shall follow in order to use the Licensed Software. The User shall use the Licensed Software by agreeing with the terms of this Software License Agreement.
Article 8 Termination In case the User falls under any of the events described in the following items, the Licensor may immediately terminate this Agreement or claim that the User compensates for the damage incurred by the Licensor due to such event: (1) when the User violated any provision of this Agreement; or (2) when a petition has been filed against the User for an attachment, provisional attachment, provisional disposition or any other compulsory execution.
CONTENTS BEFORE USE BEFORE USE 2 BASICS 3 GETTING STARTED 4 1 Select the display language and cancel the demonstration 2 Set the clock and date 3 Set the initial settings HD RadioTM tuner / RADIO 5 AUX 7 CD / USB / iPod / ANDROID 7 Pandora® 10 iHeartRadio® 11 SiriusXM® Radio 12 BLUETOOTH® 15 AUDIO SETTINGS 21 DISPLAY SETTINGS 23 REFERENCES 24 Maintenance More information IMPORTANT • To ensure proper use, please read through this manual before using this product.
BASICS Faceplate Remote control (RC-406) Loading slot Display window Remote sensor (Do not expose to bright sunlight.) Lights up when Bluetooth connection is established. ( 15) Pull out the insulation sheet when using for the first time. How to replace the battery Reset button Press twice within 5 seconds. Volume knob Flashes when the unit enters searching status. To On the faceplate On the remote control Turn on the power . Press • Press and hold to turn off the power.
GETTING STARTED To adjust the clock 3 Turn the volume knob to select [CLOCK ADJUST], then press the knob. 4 Turn the volume knob to make the settings, then press the knob. Hour Minute 5 Turn the volume knob to select [CLOCK FORMAT], then press the knob. 6 Turn the volume knob to select [12H] or [24H], then press the knob.
GETTING STARTED HD Radio™ tuner/ RADIO TUNER SETTING (For / ) You can tune in to both conventional and HD Radio broadcasts. • To find HD Radio stations in your area, visit . (For / ) You can only tune in to conventional broadcast. PRESET TYPE NORMAL: Memorizes one station for each preset button in each band (FM1/ FM2/ FM3/ AM). ; MIX: Memorizes one station or SiriusXM channel for each preset button, regardless of the selected band or SiriusXM channel.
HD Radio™ tuner/ RADIO Default: XX Direct Access Tuning (using RC-406) 1 Press DIRECT to enter Direct Access Tuning. 2 Press the number buttons to enter a frequency. 3 Press to search for a station or channel. TUNER SETTING (for or DIRECT. • To cancel, press • If no operation is done for 10 seconds after step 2, Direct Access Tuning is automatically canceled. Select an HD Radio multicast channel (for / Other settings 1 Press the volume knob to enter [FUNCTION].
AUX CD / USB / iPod / ANDROID Preparation: Select [ON] for [BUILT-IN AUX]. ( 5) Start playback The source changes automatically and playback starts. Start listening 1 Connect a portable audio player (commercially available). Auxiliary input jack Label side M Eject disc Portable audio player USB input terminal USB 3.5 mm (1/8") stereo mini plug with “L” shaped connector (commercially available) CA-U1EX (max.: 500 mA) (optional accessory) 2 Press repeatedly to select AUX.
CD / USB / iPod / ANDROID Select control mode While in iPod/ iPod FRONT/ iPod REAR source, press 5 repeatedly. MODE ON : Control iPod using the iPod itself. However, you can still play/pause, file skip, fast-forward or reverse from this unit. MODE OFF : Control iPod from this unit. To On the faceplate On the remote control Playback / pause Press Press Reverse / Fast-forward*4 Press and hold S / T. Press and hold S / Select a track/file Press S / T. Press S / Select a folder*5 Press J / K.
CD / USB / iPod / ANDROID Select a file from a folder/list . 1 Press 2 Turn the volume knob to select a folder/list, then press the knob. 3 Turn the volume knob to select a file, then press the knob. Quick Search If you have many files, you can search through them quickly. Turn the volume knob quickly to browse through the list quickly. – Not applicable for iPod. (or) Press S / T to search at a preset skip search ratio. ( [SKIP SEARCH]) • Pressing and holding S / T searches at a 10% ratio.
Pandora® Preparation: Install the latest version of the Pandora application on your device (iPhone/ iPod touch), then create an account and log in to Pandora. • Select [ON] for [PANDORA SRC]. ( 5) Create and save a new station . 1 Press 2 Turn the volume knob to select [NEW STATION], then press the knob. 3 Turn the volume knob to select [FROM TRACK] or [FROM ARTIST], then Start listening 1 Open the Pandora application on your device. 2 Connect your device to the USB input terminal. press the knob.
Pandora® Delete a station While listening to PANDORA... 1 Press the volume knob to enter [FUNCTION]. 2 Turn the volume knob to select [SYSTEM], then press the knob. 3 Turn the volume knob to select [STATION DEL], then press the knob. 4 Turn the volume knob to select [SORT BY A-Z] or [SORT BY DATE], then press the knob. 5 Turn the volume knob to select the desired station to delete, then press the knob. 6 Turn the volume knob to select [YES], then press the knob. 7 Press and hold to exit. .
iHeartRadio® SiriusXM® Radio Search and store a station . 1 Press 2 Turn the volume knob to select a category, Only SiriusXM® brings you more of what you love to listen to, all in one place. Get over 140 channels, including commercial-free music plus the best sports, news, talk, comedy and entertainment. Welcome to the world of satellite radio. A SiriusXM Vehicle Tuner and Subscription are required. For more information, visit www.siriusxm.com. then press the knob.
SiriusXM® Radio 5 Turn the volume knob to select a channel, then press the knob. (or) Press S / T to search for a channel manually. • Pressing and holding S / T changes the channel rapidly. If a locked channel or a mature channel is selected, a pass code input screen appears. Enter the pass code to receive the channel. ( 14) To change the tuning method for S / T: Press .
SiriusXM® Radio Default: XX TuneScan™ You can get a short preview of the songs that you have missed on each of your SmartFavorite music channels or currently tuned music channel. Press and hold to start scanning the first 6 seconds of the recorded music contents. • To listen to the current song, press the volume knob to stop scanning. The unit continues playing the current song. • To select the previous/next song, press S / T. • To cancel scanning, press and hold the volume knob.
BLUETOOTH® BLUETOOTH — Connection Supported Bluetooth profiles – Hands-Free Profile (HFP) – Advanced Audio Distribution Profile (A2DP) – Audio/Video Remote Control Profile (AVRCP) – Serial Port Profile (SPP) – Phonebook Access Profile (PBAP) Supported Bluetooth codecs – Sub Band Codec (SBC) – Advanced Audio Coding (AAC) – aptX Codec (aptX) (for / ) Connect the microphone MIC (Microphone input terminal) Microphone (supplied) Adjust the microphone angle Pair and connect a Bluetooth device for the first ti
BLUETOOTH® Connect with a remote device by One-touch (NFC) (for / ) Near Field Communication (NFC) enables short-range wireless communication between the unit and remote devices. By holding an NFC-compatible remote device near to the N-Mark on the unit, the unit and remote device proceed to complete pairing and established the BLUETOOTH connection automatically. 1 Activate the NFC function on the remote device. Refer to the instruction manual of the remote device for more information.
BLUETOOTH® To On the faceplate Default: XX On the remote control While talking on the first incoming call... MIC GAIN –10 — +10 (–4): The sensitivity of the microphone increases as the number increased. Answer another incoming call and hold the current call Press . Press . NR LEVEL –5 — +5 (0): Adjust the noise reduction level until the least noise is being heard during a phone conversation. Reject another incoming call Press . Press .
BLUETOOTH® Make a call NUMBER DIAL 1 Turn the volume knob to select a number (0 to 9) or character ( , #, +). 2 Press S / T to move the entry position. Repeat steps 1 and 2 until you finish entering the phone number. 3 Press the volume knob to call. (or using RC-406) 1 Press the number buttons (0 to 9) to enter the phone number. 2 Press to call. VOICE Speak the name of the contact you want to call or the voice command to control the phone functions.
BLUETOOTH® Settings in memory Store a contact in memory You can store up to 6 contacts into the number buttons (1 to 6). 1 Press to enter Bluetooth mode. 2 Turn the volume knob to select [CALL HISTORY], [PHONE BOOK], or [NUMBER DIAL], then press the knob. 3 Turn the volume knob to select a contact or enter a phone number. If a contact is selected, press the volume knob to show the phone number. 4 Press and hold one of the number buttons (1 to 6). “STORED” appears when the contact is stored.
BLUETOOTH® BLUETOOTH — Audio Bluetooth test mode You can check the connectivity of the supported profile between the Bluetooth device and the unit. • Make sure there is no Bluetooth device paired. 1 Press and hold . “PLEASE PAIR YOUR PHONE PIN 0000” appears. 2 Search and select this unit model name (DPX79 BH/ DPX70 BH/ DPX59 BT/ DPX50 BT) on the Bluetooth device. 3 Operate the Bluetooth device to confirm pairing. “TESTING” flashes on the display.
BLUETOOTH® Internet radio via Bluetooth Listen to Pandora You can listen to Pandora on the Android device via Bluetooth on this unit. Preparation: Select [ON] for [PANDORA SRC]. ( 5) 1 Open the Pandora application on your device. 2 Connect your Bluetooth audio player via Bluetooth connection. ( 15) 3 Press repeatedly to select PANDORA/ PANDORA FRONT/ PANDORA REAR. The source switches and broadcast starts automatically. You can operate Pandora in the same way as Pandora for iPod/iPhone.
AUDIO SETTINGS LOUDNESS LEVEL1/ LEVEL2: Selects your preferred low and high frequencies boost to produce a well-balanced sound at a low volume level. ; OFF: Cancels. SUBWOOFER SET ON: Turns on the subwoofer output. ; OFF: Cancels. FADER R15 to F15 (0): Adjusts the rear and front speaker output balance. BALANCE L15 to R15 (0): Adjusts the left and right speaker output balance. VOLUME OFFSET FRONT (Not applicable for TUNER source, AUX source and SIRIUS XM source.
DISPLAY SETTINGS AUDIO SETTINGS REAR HPF R - HPF FRQ R - HPF SLOPE (Refer FRONT HPF, 22.) R - HPF GAIN SUBWOOFER LPF SW LPF FRQ 30HZ/ 40HZ/ 50HZ/ 60HZ/ 70HZ/ 80HZ/ 90HZ/ 100HZ/ 120HZ/ 150HZ/ 180HZ/ 220HZ/ 250HZ: Adjusts the crossover frequency for the subwoofer (low pass filter). ; THROUGH: All signals are sent to the subwoofer. SW LPF SLOPE –6DB/ –12DB/ –18DB/ –24DB: Adjusts the crossover slope. (Selectable only if a setting other than [THROUGH] is selected for [SW LPF FRQ].
REFERENCES DISPLAY SETTINGS Default: XX COLOR SELECT DIMMER BRIGHTNESS TEXT SCROLL Select color for ALL ZONE, ZONE 1 and ZONE 2 separately. 1 Select a zone for setting. ( 23) 2 Select a color for the selected zone. VARIABLE SCAN/ CUSTOM R/G/B/ preset colors* To make your own color, select [CUSTOM R/G/B]. The color you have made will be stored in [CUSTOM R/G/B]. 1 Press the volume knob to enter the detailed color adjustment. 2 Press S / T to select the color (R/ G/ B) to adjust.
REFERENCES Playable files • Playable audio file: MP3 (.mp3), WMA (.wma), AAC (.aac) • Playable disc media: CD-R/CD-RW/CD-ROM • Playable disc file format: ISO 9660 Level 1/2, Joliet, Long file name. • Playable USB device file system: FAT12, FAT16, FAT32 Even when audio files comply with the standards listed above, playback may be impossible depending on the types or conditions of media or device. The AAC (.m4a) file in a USB device or a CD encoded by iTunes cannot be played on this unit.
REFERENCES About HD Radio™ Technology • Adjacent to traditional main stations are HD2/HD3 Channels, providing new original programming on the FM dial. • HD Radio broadcasts deliver crystal clear, CD-like digital audio quality to consumers; eliminates background noise. • Program Info provides song name, artist, station ID, and other relevant data to enrich the listening experience. Change the display information Each time you press DISP, the display information changes.
TROUBLESHOOTING Remedy Symptom Remedy • Adjust the volume to the optimum level. • Check the cords and connections. “NA FILE” Make sure the disc contains supported audio files. ( 25) “MISWIRING CHECK WIRING THEN PWR ON” appears. Turn the power off, then check to be sure the terminals of the speaker wires are insulated properly. Turn the power on again. “NO DISC” Insert a playable disc into the loading slot. “TOC ERROR” Make sure the disc is clean and inserted properly.
TROUBLESHOOTING Pandora “NO DEVICE” or “READING” keeps flashing. • Make sure KENWOOD MUSIC PLAY APP is installed on the Android device. ( 7) • Reconnect the Android device and select the appropriate control mode. ( 8) • If this does not solve the problem, the connected Android device does not support [BROWSE MODE]. ( 25) Symptom • Switch off the developer options on the Android device. • Reconnect the Android device.
TROUBLESHOOTING No Bluetooth device is detected. Bluetooth® Bluetooth pairing cannot be made. Remedy • Search from the Bluetooth device again. • Reset the unit. ( 3) • Make sure you have entered the same PIN code to both the unit and Bluetooth device. • Delete pairing information from both the unit and the Bluetooth device, then perform pairing again. ( 15) Echo or noise is heard during a phone conversation. • Adjust the microphone unit’s position. ( 15) • Check the [ECHO CANCEL] setting.
SPECIFICATIONS Laser Diode GaAIAs Digital Filter (D/A) 8 times over sampling Frequency Response (±3 dB) 20 Hz — 20 kHz Spindle Speed 500 rpm — 200 rpm (CLV) Signal-to-Noise Ratio 75 dB (STEREO) Wow & Flutter Below measurable limit 530 kHz — 1 700 kHz (10 kHz space) Frequency Response (±1 dB) 20 Hz — 20 kHz Total Harmonic Distortion (1 kHz) 0.01 % CD player 87.9 MHz — 107.
Frequency Range 2.402 GHz — 2.480 GHz Output Power +4 dBm (MAX), 0 dBm (AVE) Power Class 2 Maximum Communication Range Line of sight approx. 10 m (32.8 ft) Profile HFP (Hands-Free Profile) A2DP (Advanced Audio Distribution Profile) AVRCP (Audio/Video Remote Control Profile) SPP (Serial Port Profile) PBAP (Phonebook Access Profile) Auxiliary Bluetooth Ver.2.1+EDR / Bluetooth 3.
INSTALLATION / CONNECTION Warning • The unit can only be used with a 12 V DC power supply, negative ground. • Disconnect the battery’s negative terminal before wiring and mounting. • Do not connect Battery wire (yellow) and Ignition wire (red) to the car chassis or Ground wire (black) to prevent a short circuit. • Insulate unconnected wires with vinyl tape to prevent a short circuit. • Be sure to ground this unit to the car’s chassis again after installation.
Installing the unit (in-dash mounting) Do the required wiring. ( 34) When installing without the mounting sleeve 1 Remove the mounting sleeve and trim plate Bend the appropriate tabs to hold the mounting sleeve firmly in place. from the unit. 2 Align the holes in the unit (on both sides) with the vehicle mounting bracket and secure the unit with screws (supplied/ commercially available).
Wiring connection When connecting to an external amplifier, connect its ground wire to the car’s chassis to avoid damaging the unit. IMPORTANT : We recommend installing the unit with a commercially available custom wiring harness specific for your car and leave this job to professionals for your safety. Consult your car audio dealer. MIC (Microphone input terminal) ( 15) Rear/ front/ subwoofer output / : USB cable (DC 5 V 1.
• HD Radio Technology manufactured under license from iBiquity Digital Corporation. U.S. and Foreign Patents. HD Radio™ and the HD, HD Radio, and “Arc” logos are proprietary trademarks of iBiquity Digital Corp. • “Made for iPod,” and “Made for iPhone” mean that an electronic accessory has been designed to connect specifically to iPod, or iPhone, respectively, and has been certified by the developer to meet Apple performance standards.
MILITARY Units purchased through theU.S A. military exchange service overseas may oe serviced urder warranty in the continental U.S.A., subject to the lollmvmg cond1t:ons 1) The miginatwarranty ism effect 2) Proof of purchase is prov1ded to the sen•icer WARRANTY FOR MILITARY MARKET Kenwood corporal ron is proud of the quality and workmanship ol itsaudio equipment This umt has been properly designed. tested and rnspecled Detore it was shipped to you.
U.S A. JVCKENWOOD USA Corporation This wauantywill be honored only in the U.S.A. WHO IS PROTECTED This warranty is enforceable only by the original purchaser. KENWOOD LIMITED WARRANTY FOR CAR STEREO COMPONENTS WHAT WE WILL PAY FOR We will pay lor all labor and material expenses lor covered items. Payment of shippiny charges is discussed mthe next section ot this wananty. HOW LONG IS THE WARRANTY Kenwood U.S.A.