KDC-BT34U CD-RECEIVER INSTRUCTION MANUAL CD-RECEIVER BEDIENUNGSANLEITUNG CD-PECИBEP ИHCTPУKЦИЯ ПO ЭKCПЛУATAЦИИ © 2013 JVC KENWOOD Corporation EN_KDC_BT34U_EN_001B.
For Israel Information on Disposal of Old Electrical and Electronic Equipment and Batteries (applicable for EU countries that have adopted separate waste collection systems) Products and batteries with the symbol (crossed-out wheeled bin) cannot be disposed as household waste. Old electrical and electronic equipment and batteries should be recycled at a facility capable of handling these items and their waste byproducts.
The marking of products using lasers The label is attached to the chassis/case and says that the component uses laser beams that have been classified as Class 1. It means that the unit is utilizing laser beams that are of a weaker class. There is no danger of hazardous radiation outside the unit. Kennzeichnung von Geräten mit Laser-Abtastern Das Etikett ist am Chassis/Gehäuse angebracht und besagt, dass sich die Komponente Laserstrahlen bedient, die als Laserstrahlen der Klasse 1 klassifiziert wurden.
CONTENTS BEFORE USE BEFORE USE 2 BASICS 3 GETTING STARTED 4 RADIO 5 AUX 6 CD / USB / iPod 6 BLUETOOTH® 8 AUDIO SETTINGS 13 DISPLAY SETTINGS 14 MORE INFORMATION 14 TROUBLESHOOTING 15 SPECIFICATIONS 16 INSTALLATION / CONNECTION 18 Warning Do not operate any function that takes your attention away from safe driving. Caution Volume setting: • Adjust the volume so that you can hear sounds outside the car to prevent accidents.
BASICS Faceplate Attach Volume knob (turn/press) Loading slot Detach Display window How to reset Your preset adjustments will also be erased. Detach button To Do this (on the faceplate) Turn on the power Press B SRC. • Press and hold to turn off the power. Adjust the volume Turn the volume knob. Select a source Press B SRC repeatedly. Change the display information Press DISP SCRL repeatedly. • Press and hold to scroll the current display information. ENGLISH | EN_KDC_BT34U_EN_3.
GETTING STARTED While in clock display screen... Press and hold DISP SCRL to enter clock adjustment mode directly. Then, perform step 4 to set the clock. 3 1 Select the display language and cancel the demonstration When you turn on the power (or after you reset the unit), the display shows: “SEL LANGUAGE” “PRESS” “VOLUME KNOB” 1 Turn the volume knob to select [ENG] (English) or [RUS] (Russian), then press the knob. [ENG] is selected for the initial setup.
GETTING STARTED RUSSIAN SET Selects the display language for [FUNCTION] menu and Tag information (folder name, file name, song title, artist name, album name) if applicable. RUSSIAN OFF: Display language is English. ; РУССКИЙ BКЛ: Display language is Russian. P-OFF WAIT Applicable only when the demonstration mode is turned off. Sets the duration when the unit will automatically turns off (while in standby mode) to save the battery.
RADIO AUX PTY SEARCH Preparation: Select [ON] for [BUILT-IN AUX]. ( 4) Press the volume knob to enter PTY language selection. Turn the volume knob to select the PTY language (ENGLISH/ FRENCH/ GERMAN), then press the knob. Selects the available Program Type (see the following), then, press S / T to start. Start playback The source changes automatically and playback starts. Start listening 1 Connect a portable audio player CD (commercially available).
CD / USB / iPod Select a track/file from a list To Do this Pause or resume playback Press 6 IW. Select a track/file Press S / T. Select a folder *3 Press J / K. Reverse/Fast-forward Press and hold S / T. Repeat play *4 Random play *4 Press 4 repeatedly. • Audio CD: TRACK REPEAT, REPEAT OFF • MP3/WMA/WAV file or iPod: FILE REPEAT, FOLDER REPEAT, REPEAT OFF • KENWOOD Music Editor Light (KME Light)/ KENWOOD Music Control (KMC) file ( 14): FILE REPEAT, REPEAT OFF Press 3 repeatedly.
BLUETOOTH® CD / USB / iPod Select a song by name While listening to iPod... 1 Press . 2 Turn the volume knob to select a category, then press the knob. 3 Turn the volume knob quickly to enter character search. 4 Turn the volume knob to select the character to be searched for. 5 Press S / T to move to the entry position. You can enter up to 3 characters. 6 Press the volume knob to start searching. 7 Turn the volume knob to make a selection, then press the knob.
BLUETOOTH® Pair a Bluetooth device When connecting a Bluetooth device to the unit for the first time, perform pairing between the unit and the device. Once the pairing is completed, the Bluetooth device will remain registered in the unit even if you reset the unit. • Up to five devices can be registered (paired) in total. • A maximum of two Bluetooth phones and one Bluetooth audio device can be connected at any time. • This unit supports Secure Simple Pairing (SSP).
BLUETOOTH® Improve the sound quality during a call While talking on the phone... 1 Press the volume knob to enter [FUNCTION]. 2 Turn the volume knob to make a selection (see the following table), then press the knob. 3 Press and hold to exit. To return to the previous setting item or hierarchy, press . Default: XX MIC GAIN –20 — +8 (0): The sensitivity of the microphone increases as the number increased.
BLUETOOTH® BATT* LOW/ MID/ FULL: Shows the strength of the battery. SIGNAL* NO SIGNAL/ LOW/ MID/ MAX: Shows the strength of the current received signal. SETTINGS AUTO ANSWER Default: XX 1 — 30: The unit answer incoming call automatically in the selected time. ; OFF: Cancels. RING MODE SYSTEM: The unit rings to notify you when a call/text message comes in. (Default ring tone is different according to the paired device.) • CALL: Selects your preferred ring tone (TONE 1 — 5) for incoming calls.
BLUETOOTH® 3 Turn the volume knob to select a contact. If a contact is selected, press the volume knob to show the phone number. 4 Press and hold the volume knob to enter delete mode. 5 Turn the volume knob to select [DELETE ONE] or [DELETE ALL], then press the knob. DELETE ONE: Selected name or phone number in step 3 is deleted. DELETE ALL: All names or phone numbers from the selected menu in step 2 is deleted. 6 Turn the volume knob to select [YES] or [NO], then press the knob.
AUDIO SETTINGS While listening to any source... 1 Press the volume knob to enter [FUNCTION]. 2 Turn the volume knob to select [AUDIO CONTROL], then press the knob. 3 Turn the volume knob to make a selection (see the following table), then press the knob. Repeat step 3 until the desired item is selected or activated. 4 Press and hold to exit. To return to the previous setting item or hierarchy, press .
DISPLAY SETTINGS MORE INFORMATION 1 Press the volume knob to enter [FUNCTION]. 2 Turn the volume knob to select [DISPLAY], General About KENWOOD Music Editor Light and KENWOOD Music Control • This unit can only play the following CDs: then press the knob. 3 Turn the volume knob to make a selection (see the following table), then press the knob. Repeat step 3 until the desired item is selected or activated. 4 Press and hold to exit. To return to the previous setting item or hierarchy, press .
TROUBLESHOOTING Sound cannot be heard. “PROTECT” appears and no operations can be done. • Sound cannot be heard. • The unit does not turn on. • Information shown on the display is incorrect. The unit does not work at all. • Radio reception is poor. • Static noise while listening to the radio. Remedy • Adjust the volume to the optimum level. • Check the cords and connections. Check to be sure the terminals of the speaker wires are insulated properly, then reset the unit.
SPECIFICATIONS TROUBLESHOOTING Phone sound quality is poor. • Voice calling method is not successful. • “N/A VOICE TAG” appears. FM Frequency Range 87.5 MHz — 108.0 MHz (50 kHz space) Usable Sensitivity (S/N = 26 dB) 0.71 μV/75 Ω Quieting Sensitivity (DIN S/N = 46 dB) 2.0 μV/75 Ω • Use voice calling method in a more quiet environment. • Reduce the distance from the microphone when you speak the name. • Make sure the same voice as the registered voice tag is used.
Audio Bluetooth USB 1.1, USB 2.0 (Full speed) File System FAT12/16/ 32 Maximum Supply Current DC 5 V MP3 Decode Compliant with MPEG-1/2 Audio Layer-3 WMA Decode Compliant with Windows Media Audio WAV Decode Linear-PCM Version Bluetooth Ver.2.1+EDR Certified Frequency Range 2.402 GHz — 2.480 GHz Output Power +4 dBm (MAX), 0 dBm (AVE) Power Class 2 Maximum Communication Range Line of sight approx.
INSTALLATION / CONNECTION Warning • The unit can only be used with a 12 V DC power supply, negative ground. • Disconnect the battery’s negative terminal before wiring and mounting. • Do not connect Battery wire (yellow) and Ignition wire (red) to the car chassis or Ground wire (black) to prevent a short circuit. • Insulate unconnected wires with vinyl tape to prevent a short circuit. • Be sure to ground this unit to the car’s chassis again after installation.
Wiring connection Part list for installation Rear/subwoofer output (A) Faceplate Fuse (10 A) Antenna terminal Microphone input jack ( 8) Connecting the ISO connectors on some VW/Audi or Opel (Vauxhall) automobiles You may need to modify the wiring of the supplied wiring harness as illustrated below.