CD-RECEIVER KDC-BT60U KDC-6047U INSTRUCTION MANUAL The latest version of the Instruction Manual can be downloaded from www. kenwood.com/cs/ce/. Before reading this manual, please access this site to check whether your manual is the latest one.
Contents Before use 4 Bluetooth Audio Operation Component names and functions 6 Connecting a Bluetooth Device Basic Operation General operation 7 Before Using Common Operation Menu List Operation iPod/iPhone Operation 8 Basic Operation Selecting a song by browsing iPod Play Mode iPod Setting Selecting the Search mode Direct Search Related Search Alphabet Search Skip Search My Playlist USB device Operation 14 Basic Operation Music Search Play Mode Basic Operation of Disc Changer (Optional) Dire
DSP Setup 40 Car Type Selection Speaker Setting Car Type Fine Adjustments X’Over Setting Audio Preset Memory Audio Preset Recall Favorite Control 44 Favorite Preset Memory Favorite Preset Recall Favorite Preset Memory Delete Bluetooth Setup 46 Bluetooth Setting Registering Bluetooth device Registering PIN Code Selecting the Bluetooth device You Wish to Connect Deleting a Registered Bluetooth device Downloading the Phone Book Adding a Voice Dialing Command Setting a Voice Command for Category SMS (S
Before use 2WARNING To prevent injury or fire, take the following precautions: To prevent a short circuit, never put or leave any metallic objects (such as coins or metal tools) inside the unit. Do not use this unit before canceling Demonstration mode! This unit is initially set on the Demonstration mode. When using this unit for the first time, cancel the Demonstration mode. Refer to (page 35).
Handling CDs • Do not touch the recording surface of the CD. • Do not stick tape etc. on the CD, or use a CD with tape stuck on it. • Do not use disc type accessories. • Clean from the center of the disc and move outward. • When removing CDs from this unit, pull them out horizontally. • If the CD center hole or outside rim has burrs, use the CD only after removing the burrs with a ballpoint pen etc. CDs that cannot be used • CDs that are not round cannot be used.
Component names and functions 1 2 3 10 11 5 4 6 AUX 7 8 9 1 Release button To drop the faceplate down to open and CD can be inserted or ejected (press the button). 2 [MENU] button To select a song or set functions. See
General operation Before Using Menu List Operation Exit of the Demonstration Mode Turn off the demonstration mode when you use it for the first time after installation. The basic operating procedure for using this function is described below. The individual function items are covered in the operating procedures. Press the [VOL] knob to quit the demonstration mode when the messages “To Cancel Demo Press the Volume Knob” are displayed (approx. 15 seconds).
iPod/iPhone Operation SRC MENU VOL DISP 4 38 ¢ SEARCH MODE KCA-iP101 (optional accessory) is required to connect an iPod. / TI Basic Operation 2 Enter Menu List mode Press the [MENU] button. Playing iPod 3 Turn the [VOL] knob and press it when the desired item is displayed. Select “Music”. 4 Select a song • Connect an iPod When connected, the source is switched automatically and a song starts playing. • Select iPod source Press the [SRC] button.
Play Mode You can select a Play Mode, such as Random play and Repeat play. 1 2 Select iPod source 3 Turn the [VOL] knob and press it when the desired item is displayed. Select “Play Mode”. 4 Select the Play Mode Turn the [VOL] knob. iPod Setting You can select following iPod Setting items. Enter Menu List mode Press the [MENU] button. Display “Play Mode” “iPod by Hand” • iPod can be operated when it conforms to the iPod control function.
iPod/iPhone Operation Selecting the Search mode Direct Search You can select the most suited search method for the desired song from 4 types of the Search mode. You can quickly search the desired song by specifying its Search item (artist, album, etc.) and initial. Normal playing Display “Direct Search” “Related Search” “Recall My Playlist” “Delete My Playlist” “Register My P-list” Overview You can quickly search the desired song by specifying its Search item (artist, album, etc.) and initial.
Related Search Alphabet Search Searches for music of the same artist or genre as the one being played. You can select a song by alphabet. This function searches songs whose name contain the specified character(s) in the list of the selected Search item (artist, album, etc). 1 2 3 Play the music in iPod 4 Select the Search item Turn the [VOL] knob and press it when the desired Search item is selected. Press the [SEARCH MODE] button.
iPod/iPhone Operation Skip Search My Playlist You can scroll up or down according to the number of the selected Search items so that you can quickly switch the display position. Allows you to register your favorite songs in the Playlist of this unit. You can register up to 10 songs in the Playlist. 1 2 Select iPod source Registering Songs in the Playlist Enter browsing mode Press the [MENU] button. Turn the [VOL] knob and press it when the desired item is displayed. Select “Music” > item.
2 Enter Delete Playlist mode Turn the [VOL] knob and press it when the desired item is displayed. Select “Delete My Playlist”. 3 Turn the [VOL] knob and press it when the desired item is displayed. Select ”Delete One” or ”Delete All”. Selecting “Delete All” moves to step 5 and all songs are deleted. 4 Turn the [VOL] knob and press it when the desired item is displayed. Select the song you want to delete. 5 Turn the [VOL] knob and press it when the desired item is displayed. Select ”Yes”.
USB device Operation SRC MENU VOL DISP 4 38 ¢ / TI SEARCH MODE When connecting the USB device, usage of the CA-U1EX (option) is recommended. Basic Operation File Search Playing USB device Selecting the file you want to listen to from the device being played now. • Connect a USB device When connected, the source is switched automatically and a song starts playing. USB device Display “Music” • Select USB source Press the [SRC] button.
1 ¡! USB Setting 2 You can select following USB Setting items. ¡" ¡# Cancelling Menu List mode Press the [MENU] button for at least 1 second, and then press it again briefly. ⁄ • When you search a song in the File Search mode, the unit memorizes the position of the song being played after the search. To set a different Menu item after searching a song, press the [MENU] button for at least 1 second to move to the first hierarchy.
USB device Operation Skip Search Function of remote control You can scroll up or down according to the number of the selected Search items so that you can quickly switch the display position. Searching the music by entering the file number. 1 2 Select USB source Enter File Search mode Press the [MENU] button. Turn the [VOL] knob and press it when the desired item is displayed. Select “Music” > item. 3 Enter Skip Search mode Press the [SEARCH MODE] button.
Music CD/ Audio file Operation Release MENU VOL DISP SEARCH MODE Fast Forwards or Fast Backwards Hold down the [4] or [¢] button. ⁄ • No sound is output while playing audio file. SRC 4 38 ¢ / TI Pause and Play Press the [38] button to pause or resume playback. Basic Operation Function of Internal CD source Drop open the faceplate Press the Release button. Selecting the music you want to listen to from the disc being played now.
Music CD/ Audio file Operation Play Mode “Magazine Random” You can select a Play Mode, such as Random play and Repeat play. 1 2 Select CD source 3 Turn the [VOL] knob and press it when the desired item is displayed. Select “Play Mode”. 4 “Track Repeat” “Disc Repeat” Enter Menu List mode Press the [MENU] button. Select the Play Mode Turn the [VOL] knob.
Function of remote control Direct Music Search Searching the music by entering the track number. 1 Enter Direct Music Search mode Press the [DIRECT] button on the remote control. 2 Enter the music number Press the number buttons on the remote control. 3 Search the music Press the [4] or [¢] button. Cancelling Direct Music Search Press the [DIRECT] button. ⁄ • Direct Music Search cannot be performed during playing of Random play or scan play.
Tuner Operation SEARCH MODE SRC MENU VOL 4 ¢ 3 Turn the [VOL] knob and press it when the desired item is displayed. Select “Settings”. 4 Select the setting item to adjust Turn the [VOL] knob and press it when the desired item is displayed. Display “Settings” “Local Seek” / TI Basic Operation Selecting Tuner source Press the [SRC] button. Turn the [VOL] knob and press it when the desired item is displayed. Select the “Tuner” display.
news bulletin volume is the same level that was set for Traffic Information. • Forced MONO Strong electrical fields (such as from power lines) may cause unstable sound quality when it is set to ON. In such a situation, turn it OFF. desired item is displayed. Select “YES”. When 6 stations that can be received are put in the memory, auto memory entry closes. Preset Tuning Station Preset Memory Recalling the stations in the memory. Putting a station in the memory.
Tuner Operation PTY (Program Type) Program Type Preset Selecting the Program Type below and searching for a station. Putting the Program Type in the Preset button memory and quick recall.
Function of KDC-BT60U KDC-6047U with KCA-BT200 (Optional Accessory) Bluetooth Audio Operation Basic Operation SRC MENU VOL 4 38 ¢ / TI Selecting Bluetooth Audio source Press the [SRC] button. Turn the [VOL] knob and press it when the desired item is displayed. Select the “BT Audio” display. ✍✍SRC Select mode 2: Pressing the [SRC] button repeatedly switches source. Connecting a Bluetooth Device Pause and play Press the [38] button.
Function of KDC-BT60U KDC-6047U with KCA-BT200 (Optional Accessory) Operation of hands-free phoning SEARCH MODE SRC MENU VOL ⁄ • When registering from this unit, refer to (page 47). • For details on the Bluetooth cell-phone with the handsfree function, see (page 57). 4 38 ¢ / TI Connecting a Bluetooth Device Before use the Bluetooth device, you need to connect Bluetooth device to this unit. The following 3 steps procedure is necessary. Step 1.
Answering another Incoming Call after Terminating the Current Call Press the [SRC] button. Continuing the Current Call 1 2 Press the [VOL] knob. Press the [ ] / [TI] button. Speed Dialing (Preset Dial) 1 Enter Bluetooth mode KDC-BT60U Turn the [VOL] knob and press it when the desired item is displayed. Select “REJECT”. Press the [ ] button. KDC-6047U Press the [TI] button for at least 1 second. Answering the Waiting Call after Terminating the Current Call Press the [SRC] button.
Function of KDC-BT60U KDC-6047U with KCA-BT200 (Optional Accessory) Operation of hands-free phoning Calling a Number in the Phone Book 1 ✍✍Switching between Display Modes Press the [DISP] button. Pressing this button each time switches between name and telephone number. Enter Bluetooth mode KDC-BT60U Press the [ ] button. KDC-6047U 4 Press the [TI] button for at least 1 second. 2 Select the Phone Book mode Turn the [VOL] knob and press it when the desired item is displayed. Select “Phonebook”.
Make a Voice Dialing Call Registering to the Preset Dial Number List 1 Enter voice recognition mode Press the [VOL] button for at least 1 second. 1 2 “PB Name?” is displayed. When a beep is heard, say the name within 2 seconds. Select the phone number you wish to register Select the phone number with reference to the following: - Calling a Number in the Phone Book (page 26) - Calling a Number in the Call log (page 26) 3 “PN Type” is displayed.
Display Settings SRC MENU VOL Display Setting You can select following Display Setting items. 4 Select the source Press the [SRC] button. Turn the [VOL] knob and press it when the desired item is displayed. ✍✍SRC Select mode 2: Pressing the [SRC] button repeatedly switches source. 2 Enter Menu List mode Press the [MENU] button. 3 Enter Display Setting mode Turn the [VOL] knob and press it when the desired item is displayed. Select “Settings” > “DISP & ILLUMI”.
“ILLUMI Effect” Sets whether the key illumination brightness is changed in conjunction with the key operation. “OFF”/ “ON” “ILLUMI MSC Sets whether the key illumination color is SYNC” changed in conjunction with the sound volume. “OFF”/ “ON” ( : Factory setting) 5 Make a setting • When the “ PUSH ” icon is displayed (at the right edge of the display) Turn the [VOL] knob to select a setting value, and then press the [VOL] knob.
Display Settings Customization of 5-line Display Mode & 3-line Display Mode & iPod-like Display Mode You can customize the display of the 5-line display mode, 3-line display mode, and iPod-like display mode. 1 Select the source Press the [SRC] button. Turn the [VOL] knob and press it when the desired item is displayed. ✍✍SRC Select mode 2: Pressing the [SRC] button repeatedly switches source. 2 Enter Menu List mode Press the [MENU] button.
In Auxiliary input source Source name (“Source Name”) Spectrum analyzer & Clock (“Speana/Clock”) Date (“Date”) Blank (“Blank”) In Standby Source name (“Source Name”) Date (“Date”) Clock (“Clock”) Blank (“Blank”) Customization of Spectrum Analyzer Display Mode You can customize the display of the Spectrum analyzer display mode. 1 Select the source Press the [SRC] button. Turn the [VOL] knob and press it when the desired item is displayed.
Display Settings Illumination Color Selection Auxiliary Input Display Setting Selecting the Illumination Color of the panel. Selecting the display when changing to Auxiliary input source. 1 Enter Menu List mode Press the [MENU] button. 2 Enter Illumination color selection mode Turn the [VOL] knob and press it when the desired item is displayed. Select “Settings” > “DISP & ILLUMI” > “Color Select”.
Clock and Other Functions Release SRC 4 3. Turn the [VOL] knob to adjust the day 4. Press the [¢] button. 5. Turn the [VOL] knob to adjust the year. 6. Press the [VOL] knob. MENU VOL 7 Enter Date format mode Turn the [VOL] knob and press it when the desired item is displayed. Select “Date Mode Select”. 8 Select Date format Turn the [VOL] knob and press it when the desired item is displayed. Select from 7 types.
Clock and Other Functions Initial Settings “Favorite Delete” Deletes Favorite Preset Memory. Refer to (page 44). “Built in AMP” Selecting “OFF” turns off the built-in amplifier. Turning off the built-in amplifier improves the quality of the sound from Preout. “OFF”/ “ON” “DSI” DSI (Disabled System Indicator) of the unit blinks when the faceplate is removed. “OFF”/ “ON” You can select following Initial Setting items. 1 Select the Standby Press the [SRC] button.
Demonstration mode Setting Theft Deterrent Faceplate Turning the demonstration mode ON/OFF. The faceplate of the unit can be detached and taken with you, helping to deter theft. 1 Enter Menu List mode Press the [MENU] button. 2 Enter Demonstration mode setting Turn the [VOL] knob and press it when the desired item is displayed. Select “DEMO Mode”. 3 Set the Demonstration mode Turn the [VOL] knob and press it when the desired item is displayed. Select “ON” or “OFF”.
Audio Adjustments “2Zone” SRC MENU VOL “Preset” Sets the Dual Zone System. - Dual Zone System (page 39). Sets the audio preset. - Audio Preset Memory (page 42). - Audio Preset Recall (page 43). ( 4 Select the source Press the [SRC] button. Turn the [VOL] knob and press it when the desired item is displayed. Select a source other than “STANDBY”. ✍✍SRC Select mode 2: Pressing the [SRC] button repeatedly switches source. 2 Enter Audio Control mode Press the [VOL] knob.
Preset Equalizer curve Select Manual Equalizer Control You can select following Equalizer curve. You can adjust following Equalizer Control items. Display “Natural” “User” “Rock” “Pops” “Easy” “Top 40” “Jazz” “Game” “iPod” Equalizer curve Natural User* Rock Pops Easy Top 40 Jazz Game iPod (During iPod source only) Band “BAND1” (62.5 Hz) “BAND2” (250 Hz) “BAND3” (1 kHz) “BAND4” (4 kHz) “BAND5” (16 kHz) Select the source Press the [SRC] button.
Audio Adjustments Listening Position Selection Listening Position Fine Adjustments The sound environment can be compensated in accordance with the selected position. According to the listening position, select the position from the following settings. Making fine adjustment of the value specified at Preset position selection per speaker. Compensation seat Not compensating.
Dual Zone System Main source and sub source (Auxiliary input) output Front channel and Rear channel separately. Display Overview “2Zone Rear Volume”*1 Adjust the volume of Rear channel. “0” — “35” “Detailed Setup” “2Zone” Sets the Dual Zone System. “OFF”/ “ON” “2Zone Select”*1 Specifies the destination of sub source sound when the Dual Zone function is turned on. “Rear”/ “Front” *1 The Dual Zone System is set to “ON”. ( : Factory setting) 1 Select the source Press the [SRC] button.
DSP Setup Speaker Setting SRC MENU VOL The speaker X’Over is automatically set when the position and size of each speaker are selected from the following items. Speaker “Front” 4 Range Speaker Size Front “O.E.M.”, “10cm”, “13cm”, “16cm”, “17cm”, “18cm”, “4x6”, “5x7”, “6x8”, “6x9”, “7x10” “LOCATION” Speaker Location Front “Door”, “On Dash”, “Under Dash” “TWEETER” Speaker Size Tweeter “None”, “Use” “Rear” “SIZE” Speaker Size Rear “None”, “O.E.M.
Car Type Fine Adjustments Reference point Adjusting fine tuning of the speaker position compensation value specified at (page 40). Display “Front” “Rear” “SW” Item Front speaker Rear speaker Subwoofer Range 0 – 440 cm 0 – 440 cm 0 – 440 cm ( 1 FRONT 2 Enter Audio Control mode Press the [VOL] knob. 3 Enter Car Type Adjustment mode Turn the [VOL] knob and press it when the desired item is displayed. Select “Detailed Setup” > “Car Type Adjust”.
DSP Setup X’Over Setting Fine adjusting the following setting values corresponding to the X’Over values set in the section (page 40).
Audio Preset Recall Recalling the sound setup registered by
Favorite Control • If the contents in iPod are changed after the FAVORITE registration, the list registered in this unit becomes different from that in iPod. In this case, perform the FAVORITE registration again. MENU VOL Favorite Preset Recall FAV Favorite Preset Memory Registering the operation procedure to select your favorite broadcast station or iPod Playlists/ Artists, etc.
Select “YES”. “Completed” is displayed. Exit Favorite Preset Memory Delete mode.
Function of KDC-BT60U KDC-6047U with KCA-BT200 (Optional Accessory) Bluetooth Setup “Auto Answer” Answer a call automatically after lapse of the preset time interval for automatic answer. “OFF”/ “0s” – “8s” – “99s” “Bluetooth HF/ You can specify output speakers for hands-free Audio” voice communication and Bluetooth audio sound. “FRONT”: Outputs voice from the front speakers. “ALL”: Outputs voice from the front and rear speakers. “Call Beep” You can output a beep from the speaker when a call comes in.
the unit, the former will be used. • This function does not work for call waiting. • “Bluetooth HF/Audio” (Setting up the Voice Output Speakers) Select the speaker which is further from the microphone in order to prevent howling or echoes. • “BT F/W Update” (Displaying the Firmware Version) Display the version of the firmware of this unit. For how to update the firmware, access our web site. http://www.kenwood.
Function of KDC-BT60U KDC-6047U with KCA-BT200 (Optional Accessory) Bluetooth Setup Registering PIN Code By operating the Bluetooth device, specify the PIN code necessary for registering this unit. 1 Enter Bluetooth mode KDC-BT60U Press the [ ] button. KDC-6047U Selecting the Bluetooth device You Wish to Connect When two or more Bluetooth devices have already been registered, you need to select the Bluetooth device you wish to use. 1 KDC-BT60U Press the [TI] button for at least 1 second.
Deleting a Registered Bluetooth device You can delete a registered Bluetooth device. 1 Enter Bluetooth mode KDC-BT60U Press the [ ] button. KDC-6047U Press the [TI] button for at least 1 second. ✍✍You can also select from “Settings” in Menu List mode. 2 Enter Bluetooth device deletion mode Turn the [VOL] knob and press it when the desired item is displayed. Select “BT Settings” > “Detailed Setup” > “Device Delete”. “(name)” is displayed.
Function of KDC-BT60U KDC-6047U with KCA-BT200 (Optional Accessory) Bluetooth Setup Function of KDC-6047U 5 Adding a Voice Dialing Command Add a voice tag to the phone book for voice dialing. You can register up to 35 voice tags. 1 2 3 4 Enter Bluetooth mode Press the [TI] button for at least 1 second. ✍✍You can also select from “Settings” in Menu List mode. Enter Phone book name edit mode Turn the [VOL] knob and press it when the desired item is displayed.
⁄ • Set the voice tag for all the 5 categories. If the voice tag is not registered for all the categories, the Phone book may not be recalled by voice command.
Function of KDC-BT60U KDC-6047U with KCA-BT200 (Optional Accessory) SMS (Short Message Service) Downloading the SMS SMS (Short Message Service) Download the short message (SMS) arrived at the cell-phone so that it can be read on this unit. The SMS arrived at the cell-phone is displayed on the receiver. A newly arrived message is displayed. 1 Enter Bluetooth mode KDC-BT60U Press the [ 2 3 4 ] button. ¤ KDC-6047U • To prevent car accidents, the driver should not read the SMS while driving.
• The short message cannot be displayed during downloading the SMS.
Basic Operations of remote control In Tuner source VOL SRC • Band select: [FM]/[AM] • Station select: [4]/[¢] • Recall preset stations: [1] — [6] ATT ENT 5/∞ EXIT AUD AM FM 0—9 DIRECT (page 16, 19, 21, 26) General control • Volume control: [VOL] • Source select: [SRC] • Volume reduce: [ATT] When the button is pressed again, the volume returns to the previous level.
Hands-free phone control Preparing the remote control unit Making a call • Enter Bluetooth mode: [ ] • Select a dialing method: [5]/[∞] ➜ [ENT] • Number dial input: Input a digit: [0] – [9] Input “+”: [¢] Input “#”: [FM] Input “*”: [AM] Clear the entered phone number: [4] • Make a call: [DIRECT] Pull the battery sheet out from the remote control unit to the direction of the arrow.
Appendix About Audio file • Playable Audio file AAC-LC (.m4a), MP3 (.mp3), WMA (.wma) • Playable disc media CD-R/RW/ROM • Playable disc file format ISO 9660 Level 1/2, Joliet, Romeo, Long file name. Playable USB device USB mass storage class • Playable USB device file system FAT16, FAT32 Although the audio files are complied with the standards listed above, the play maybe impossible depending on the types or conditions of media or device.
• When connecting the USB device, usage of the CA-U1EX (option) is recommended. Normal playback is not guaranteed when a cable other than the USB compatible cable is used. Connecting a cable whose total length is longer than 5 m can result in abnormal playback. About “KENWOOD Music Editor” • This unit supports the PC application “KENWOOD Music Editor Lite ver1.0” or later. • When you use the audio file with database information added by the “KENWOOD Music Editor Lite ver1.
Appendix Menu List Common function items Display “Clock & Date” “Clock Adjust” “Time Synchronize” “Date Time Adjust” “Date Mode Select” “DISP & ILLUMI” “Display Select” “Type Select” “Side Select” “Text Select” “Graphic Select” “Status” “Color Select” “Display Off Mode” “Display Dimmer” “Contrast” “DISP N/P” “TEXT Scroll” “ILLUMI Dimmer” “ILLUMI Effect” “ILLUMI MSC SYNC” “RDS Settings” “News” “AF” “RDS Regional” “Auto TP Seek” “DEMO Mode” Page 33 – – 30, 31 30 31 30 32 28 20 35 Function items appearing
Function items appearing when the Music CD/ Audio file source is selected Display Page “Music” 17 “Play Mode” 18 “File Scan” “Track Scan” “Folder Random” “Disc Random” “Magazine Random” “File Repeat” “Folder Repeat” “Track Repeat” “Disc Repeat” “Settings” – “Clock & Date” – “DISP & ILLUMI” – “RDS Settings” – Function items appearing when the Tuner source is selected Display Page “List & Memory” 21, 21 “FM1” “FM2” “FM3” “AM” “PTY Search” 22 “Settings” – “Local Seek” 20 “Seek Mode” “Auto Memory” 21 “Forced MO
Appendix Display Indicator items Source Display Overview General "ATT" Indicates that the attenuator is active. “FAV” Indicates that the Favorite can be registered. Indicates that a disc is inserted. iPod/USB/ “CD•IN” CD/CD "SCAN" Indicates that the Scan function is ON. Changer "Fi•SCAN" Indicates that the File Scan function is ON. “D•RDM” Indicates that the Disc Random function is ON. “RDM” Indicates that the Track/File Random function is ON. “Fo•RDM” Indicates that the Folder Random function is ON.
This Product is not installed by the manufacturer of a vehicle on the production line, nor by the professional importer of a vehicle into an EU Member State. Information on Disposal of Old Electrical and Electronic Equipment and Batteries (applicable for EU countries that have adopted separate waste collection systems) roducts and batteries with the symbol P (crossed-out wheeled bin) cannot be disposed as household waste.
Accessories/ Installation Procedure Accessories • 2 1 ..........1 ..........2 • • 3* • 3 m ..........1 *Accessory of KDC-BT60U • Installation Procedure 1 To prevent short circuits, remove the key from the • 2 3 4 5 6 7 8 9 ignition and disconnect the - terminal of the battery. Make the proper input and output wire connections for each unit. Connect the wire on the wiring harness. Take Connector B on the wiring harness and connect it to the speaker connector in your vehicle.
Connecting Wires to Terminals To USB device USB connector (1m) not remove the ⁄ Do cap when you do not use the USB cable. The connector will cause the unit to malfunction if it gets in touch with any metallic part of the vehicle. R Microphone input (KDC-BT60U only) L Rear output Front output Sub Woofer output Antenna Cord Microphone (Accessory 3) R Fuse (10A) L FM/AM antenna input (JASO) AUX input (Stereo) Use the mini-plug which is stereo type and does not have any resistance.
Connecting Wires to Terminals Connector Function Guide Pin Numbers for ISO Connectors External Power Connector A-4 A-5 A-6 A-7 A-8 Cable Colour Functions Yellow Blue/White Orange/White Red Black Battery Power Control Dimmer Ignition (ACC) Earth (Ground) Connection Speaker Connector B-1 B-2 B-3 B-4 B-5 B-6 B-7 B-8 Purple Purple/Black Gray Gray/Black White White/Black Green Green/Black Rear Right (+) Rear Right (–) Front Right (+) Front Right (–) Front Left (+) Front Left (–) Rear Left (+) Rear Left (–
Installation/Removing the Unit Installation Removing the hard rubber frame 1 Engage the catch pins on the removal tool and remove the two locks on the upper level. Upper the frame and pull it forward as shown in the figure. Lock Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place. Accessory2 Removal tool ⁄ • Make sure that the unit is installed securely in place. If the unit is unstable, it may malfunction (for example, the sound may skip).
Installation/Removing the Unit Accessory of KDC-BT60U Installation the Microphone Unit 1 Check the installation position of the microphone 2 3 4 (accessory 3). Remove oil and other dirt from the installation surface. Install the microphone. Wire the cable up to the unit with it secured at several positions using tape or the like. Accessory 3 Fix a cable with a commercial item of tape. Peel the release coated paper of double-face adhesive tape to fix on the place shown above.
Troubleshooting Guide Some functions of this unit may be disabled by some settings made on this unit. ! ! ! • Cannot set up the subwoofer. • No output from the subwoofer. • Cannot set up the subwoofer position of Manual position setting. ▲ • The Dual zone function is enabled. (page 39) • In the speaker select option, None is selected for the subwoofer. (page 40) • Cannot set up the equalizer. • Cannot set up the Bass Boost.
Troubleshooting Guide Hands-free ? The hands-free talk volume is low. The hands-free talk volume is set at a low level. The hands-free talk volume can be adjusted independently. Adjust it during hands-free talk. “Mic Gain” and “NR Level” (page 46). ? No sound is heard from the rear speakers. You are talking in the hand-free talk mode. No sound is heard from the rear speakers in the hands-free talk mode. ? No beep is heard at reception of an incoming call.
N/A Device: • An unsupported USB device is connected. • Connection to the iPod has failed. Check that the connected iPod is an iPod that is supported. See (page 56) for information on supported iPods. Err No Matching: The voice tag is wrong. Voice cannot be recognized because of an unregistered voice tag, etc. Too Soft: Voice is too small and cannot be recognized. No Music Data/Error 15: • The connected USB device contains no playable audio file.
Specifications FM tuner section Frequency range (50 kHz space) : 87.5 MHz – 108.0 MHz Usable sensitivity (S/N = 26dB) : 0.7 μV/75 Ω Quieting Sensitivity (S/N = 46dB) : 1.6 μV/75 Ω Frequency response (±3.
Audio section Maximum output power : 50 W x 4 Output power (DIN 45324, +B=14.4V) : 30 W x 4 Speaker Impedance : 4 – 8 Ω Tone action BAND1 (60 Hz): ±9 dB BAND2 (250 Hz): ±9 dB BAND3 (1 kHz): ±9 dB BAND4 (4 kHz): ±9 dB BAND5 (16 kHz): ±9 dB Preout level / Load (CD) : 4000 mV/10 kΩ Preout impedance : ≤ 600 Ω Auxiliary input Frequency response (±1 dB) : 20 Hz – 20 kHz Input Maximum Voltage : 1200 mV Input Impedance : 10 kΩ General Operating voltage KDC-BT60U (10.5 – 16V allowable) : 14.
Declaration of Conformity with regard to the EMC Directive 2004/108/EC For KDC-BT60U: Declaration of Conformity with regard to the R&TTE Directive 1999/5/EC Manufacturer: Kenwood Corporation 2967-3 Ishikawa-machi, Hachioji-shi, Tokyo, 192-8525 Japan EU Representative's: Kenwood Electronics Europe BV Amsterdamseweg 37, 1422 AC UITHOORN, The Netherlands Svenska Härmed intygar Kenwood att denna KDC-BT60U stär l överensstämelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår a