Owner's Manual
Table Of Contents
Accessories/Installation Procedure
1.
To
prevent a short circuit, remove the
key
from the
ignition and disconnect the
8 battery.
2.
Make the proper input and
output
wire
connections for each unit.
3.
Connect the speaker wires
of
the wiring
harness.
4.
Connect the wiring harness wires in the following
order: ground, battery, ignition.
5.
Connect the wiring harness connector
to
the unit.
6.
Install the unit
in
your
car.
7.
Reconnect the 8 battery.
8.
Press
the reset button.
AWARNING
If you connect the ignition wire (red) and
the
battery wire
(yellow)
to
the car
chassis
(ground), you may cause a short
circuit, that
in
turn may start a
fire.
Always connect those
wires
to
the power source running through
the
fuse box.
~
• Mounting and wiring this product requires
skills
and
experience.
For
safety's
sake,
leave
the
mounting
and wiring
work
to
professionals.
Make
sure
to
ground
the
unit
to
a negative
12V
DC
power
supply.
Do not install the unit
in
a spot exposed
to
direct sunlight
or excessive heat or humidity. Also avoid places with
too
much dust or the possibility
of
water splashing.
Do not
use
your
own
screws.
Use
only the screws provided.
If
you
use
the wrong
screws,
you could damage the unit.
If
the power
is
not turned
ON
("PROTECT"
is
displayed),
the speaker wire may have a short-circuit or touched the
chassis
of
the vehicle and the protection function may
have been activated. Therefore, the speaker wire should be
checked.
If
your
car's
ignition does
not
have
an
ACC
position, connect
the ignition wires
to
a power source that can be turned on
and off with the ignition
key.
If you connect
the
ignition
wire to a power source
with
a constant voltage supply,
as
Accessories
®
Installation Procedure
@-
..........
4
~
..........
4
with
battery wires, the battery may die.
If the console
has
a lid, make
sure
to install the unit
so
that
the faceplate will not hit the lid when closing and opening.
• If the
fuse
blows, first make
sure
the wires aren't touching
to
cause
a short circuit, then replace the old fuse with one
with the
same
rating.
Insulate unconnected wires with vinyl tape or other similar
material.
To
prevent a short circuit, do
not
remove the
caps
on
the ends
of
the unconnected wires or the terminals.
Connect the speaker wires correctly
to
the terminals to
which they correspond. The unit may be damaged or
fail
to
work
if
you
share
the 8 wires or ground
them
to
any metal
part
in
the
car.
When only
two
speakers
are
being connected
to
the
system, connect the connectors either
to
both the front
output
terminals or
to
both the
rear
output
terminals (do
not mix front and
rear).
For
example, if you connect the
8j
connector
of
the left speaker to a front
output
terminal,
do
not
connect the 8 connector
to
a
rear
output
terminal.
After the unit
is
installed, check whether the brake lamps,
blinkers, wipers,
etc.
on the car
are
working properly.
Mount
the unit
so
that the
mounting
angle
is
30°
or
less.
Reception may drop
if
there
are
metal objects near the
Bluetooth antenna.
]]J
~t
~~~_
00'-
~
"."
•••
~~;
..
I1J.~
..
,J.
~
~
IF
- -
'HH
1 2 n 3 4 '.0: 5 G
31
\.~
0
'-
~
~
'1'
.
Bluetooth antenna unit
For Good Reception
To
assure
good reception, note the folloWing:
• Communicate with the cell-phone within the line-
of-sight distance
of
10m
(30
ft). The communication
range becomes shorter depending on the
surrounding environment.
The
communication
range
also
becomes shorter when there
is
an
obstacle between this unit and the cell-phone. The
above maximum communication range (10m)
is
not always
assured.
• A broadcast station or walkie-talkie located nearby
can
interfere with communication due
to
too strong
signal.
About CD players/disc changers connected
to
this unit
If the
CD
player/ disc changer
has
the "O-N" switch,
set
it to the
"N"
position.
The functions you
can
use
and the information that
can
be displayed may differ depending on the models
being connected.
English
I 35