KDC-D301 CD-PLAYER INSTRUCTION MANUAL LECTEUR DE CD MODE D’EMPLOI REPRODUCTOR DE DISCOS COMPACTOS MANUAL DE INSTRUCCIONES Take the time to read through this instruction manual. Familiarity with installation and operation procedures will help you obtain the best performance from your new CD-player. For your records COMPACT DIGITAL AUDIO Record the serial number, found on the back of the unit, in the spaces designated on the warranty card, and in the space provided below.
English Contents 2Warning 2CAUTION Before use Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. In compliance with Federal Regulations, following are reproductions of labels on, or inside the product relating to laser product safety. Safety Precautions ........................................................................3 Handling Compact Discs ...............................................................
Safety precautions NOTE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment may cause harmful interference to radio communications, if it is not installed and used in accordance with the instructions. However, there is no guarantee that interference will not occur in a particular installation.
English Safety precautions Cleaning the Faceplate Terminals If the terminals on the unit or faceplate get dirty, wipe them with a dry, soft cloth. Handling Compact discs Cleaning the CD Slot As dust can accumulate in the CD slot, clean it occasionally. Your CDs can get scratched if you put them in a dusty CD slot. Cleaning the Unit If the faceplate of this unit is stained, wipe it with a dry soft cloth such as a silicon cloth.
Storing CDs • Do not store CDs in areas exposed to direct sunlight (such as a car seat or the dashboard) or other hot places. A CD-R or CD-RW is more susceptible than a music CD to damage from high temperatures and humidity, and in some cases, may become unusable if left in the car for long periods of time. • Remove CDs from the unit when not listening to them for a while, and put them back in their cases. Do not pile up CDs that are removed from their cases or prop them against something.
English Operations the front, thereby exposing the CD slot. Buttons and Display Release button 2 Holding the CD with the labeled side facing up, insert it in the slot. The CD will start playing. 3 Push back on the right side of the faceplate with your hand until CD PLAYER KDC-D301 INTEGRATED QUAD 1 BIT D/A CONVERTER it locks.
Switching Spectrum Analyzer Display Presetting Disc Names You can select the display to enjoy sounds with eyes. Operation for "N" Setting: Each time you press the DISP button, the spectrum analyzer display switches as following table; Operation for "O" Setting: 1 Selecting CD play source mode. 2 Each time you press the DISP button, the spectrum analyzer display switches as follows; ▼ Displays 1 to 9 are automatically shown in succession for about five seconds each.
English Operations Eject A press of the 0 button stops the CD play and ejects the CD. 0 Theft Deterrent Faceplate The faceplate of the unit can be detached and taken with you, helping to deter theft. Removing Faceplate: Press the release button and drop open the faceplate. In its dropped condition, whilst drawing the faceplate to one side, pull it to the front and remove it.
Accessories Reattaching Faceplate: Hold the faceplate so that the operation face faces the front toward you and press until it locks. The faceplate will be set and the unit will be operational. External view ......... Number of items 1 3 .........1 .........2 ▲ NOTE When there is difficulty in setting the faceplate, align the depression on the left side of the faceplate with the shaft of the unit, then lock. External view ......... Number of items 4 2 .........1 .........1 5 .........
Connections Control input 1. To prevent a short circuit, remove the key from the ignition and disconnect the - battery. 2. Set the O-N switch of this unit to suit the centre unit. 3. Connect the speaker input cable to the front speaker cable of the wiring hernees of the centre unit. 4. Connect the control cable to the control connector. 5. Install the unit in your car. 6. Reconnect the - battery. 7. Press the reset button on the centre unit.
Installation ■ Installation *…North & South America sales area only. ■ Screwing the Faceplate on the Unit (North & South America sales area only.) If you want to fasten the faceplate to the main unit so that it does not fall off, insert the provided screw (ø2.6 × 12 mm) in the holes as follows.
Installation ■ Removing the Unit English ■ Removing the hard rubber frame 1 Engage the catch pins on the removal tool and remove the two 1 Refer to the section “Removing the hard rubber frame” and locks on the lower level. Lower the frame and pull it forward as shown in the figure. 2 Remove the Hex-head screw with integral washer (M4×8) on then remove the hard rubber frame. the back panel. 3 Insert the two removal tools deeply into the slots on each side, Catch as shown.
Troubleshooting Guide What might seem to be a malfunction in your unit may just be the result of slight misoperation or miswiring. Before calling service, first check the following table for possible problems. PROBLEM The disc control mode cannot be selected. No sound can be heard, or the volume is low. The spectrum analyzer is not displayed. POSSIBLE CAUSE SOLUTION No cable has been connected to the disc changer input terminal on the unit.
Troubleshooting Guide English The following messages are displayed on the centre unit when certain problems are occurring in your system. Take the recommended actions. E-01 EJECT No CD in the unit. ] Insert the CD. NO PANEL E-30 The faceplate of this unit has been removed. ] Replace it. E-04 The CD is quite dirty. The CD is upside-down. The CD is scratched a lot. ] Clean the CD and load it correctly. E-99 Mecha Error The unit is malfunctioning for some reason.
Specifications Specifications subject to change without notice. CD player section General Laser diode ....................................................GaAlAs (λ=780 nm) Digital filter (D/A)......................................8 Times Over Sampling D/A Converter ......................................................................1 Bit Spindle speed ..............................................500 – 200 rpm (CLV) Wow & Flutter ........................................
