CD-RECEIVER KDC-X994 KDC-BT945U KDC-X794 KDC-MP745U INSTRUCTION MANUAL Before reading this manual, click the button below to check the latest edition and the modified pages. Check the latest edition Take the time to read through this instruction manual. Familiarity with installation and operation procedures will help you obtain the best performance from your new CD-receiver.
Contents Before use 4 Bluetooth Audio Operation Component names and functions 6 Connecting a Bluetooth Device Basic Operation General operation 7 Before Using Common Operation Menu List Operation iPod/iPhone Operation 8 Basic Operation Selecting a song by browsing iPod Play Mode iPod Setting Selecting the Search mode Direct Search Related Search Alphabet Search Skip Search My Playlist USB device Operation 14 17 Basic Operation Music Search Play Mode Basic Operation of Disc Changer (Optional)
DSP Setup 42 Car Type Selection Speaker Setting Car Type Fine Adjustments X’Over Setting Audio Preset Memory Audio Preset Recall Favorite Control 46 Favorite Preset Memory Favorite Preset Recall Favorite Preset Memory Delete Bluetooth Setup 48 Bluetooth Setting Registering Bluetooth device Registering PIN Code Selecting the Bluetooth device You Wish to Connect Deleting a Registered Bluetooth device Downloading the Phone Book Adding a Voice Dialing Command Setting a Voice Command for Category SMS (S
Before use 2WARNING To prevent injury or fire, take the following precautions: To prevent a short circuit, never put or leave any metallic objects (such as coins or metal tools) inside the unit. Do not use this unit before canceling Demonstration mode! This unit is initially set on the Demonstration mode. When using this unit for the first time, cancel the Demonstration mode. Refer to (page 7). How to reset your unit If this unit or the connected unit (auto disc changer, etc.
Handling CDs • Do not touch the recording surface of the CD. • Do not stick tape etc. on the CD, or use a CD with tape stuck on it. • Do not use disc type accessories. • Clean from the center of the disc and move outward. • When removing CDs from this unit, pull them out horizontally. • If the CD center hole or outside rim has burrs, use the CD only after removing the burrs with a ballpoint pen etc. CDs that cannot be used • CDs that are not round cannot be used.
Component names and functions 1 2 3 10 11 5 4 6 AUX 7 8 9 1 Release button To drop the faceplate down to open and CD can be inserted or ejected (press the button). 2 [MENU] button To select a song or set functions. See
General operation Exit of the Demonstration Mode Turn off the demonstration mode when you use it for the first time after installation. 1 Press the [VOL] knob to quit the demonstration mode when the messages “To cancel Demo press the volume knob” are displayed (approx. 15 seconds). 2 Turn the [VOL] knob to select “YES” and press the [VOL] knob. ⁄ • Demonstration mode can also be cancelled in “DEMO Mode” of Menu List mode. Refer to (page 35).
iPod/iPhone Operation SRC MENU VOL DISP 4 38 ¢ SEARCH MODE KCA-iP101 (optional accessory) is required to connect an iPod. /PLAY MODE Basic Operation 2 Enter Menu List mode Press the [MENU] button. Playing iPod 3 Turn the [VOL] knob and press it when the desired item is displayed. Select “Music”. 4 Select a song • Connect an iPod When connected, the source is switched automatically and a song starts playing. • Select iPod source Press the [SRC] button.
Play Mode ⁄ You can select a Play Mode, such as Random play and Repeat play. • In the iPod Control by Hand Mode, iPod cannot be operated using this unit. • This mode is not compatible with music information display. The display will show “iPod by Hand Mode”. • iPod can be operated when it conforms to the iPod control function. 1 2 Select iPod source Enter Play Mode Menu KDC-X994 KDC-BT945U Press the [VOL] knob for at least 1 second. KDC-X794 KDC-MP745U Press the [PLAY MODE] button.
iPod/iPhone Operation Selecting the Search mode Direct Search You can select the most suited search method for the desired song from 4 types of the Search mode. You can quickly search the desired song by specifying its Search item (artist, album, etc.) and initial. Normal playing Display “Direct Search” “Related Search” “Recall My Playlist” “Delete My Playlist” “Register My P-list” Overview You can quickly search the desired song by specifying its Search item (artist, album, etc.) and initial.
Related Search Alphabet Search Searches for music of the same artist or genre as the one being played. You can select a song by alphabet. This function searches songs whose name contain the specified character(s) in the list of the selected Search item (artist, album, etc). 1 2 3 Play the music in iPod 4 Select the Search item Turn the [VOL] knob and press it when the desired Search item is selected. Press the [SEARCH MODE] button.
iPod/iPhone Operation Skip Search My Playlist You can scroll up or down according to the number of the selected Search items so that you can quickly switch the display position. Allows you to register your favorite songs in the Playlist of this unit. You can register up to 10 songs in the Playlist. 1 2 Select iPod source Registering Songs in the Playlist Enter browsing mode Press the [MENU] button. Turn the [VOL] knob and press it when the desired item is displayed. Select “Music” > item.
2 Enter Delete Playlist mode Turn the [VOL] knob and press it when the desired item is displayed. Select “Delete My Playlist”. 3 Turn the [VOL] knob and press it when the desired item is displayed. Select ”Delete One” or ”Delete All”. Selecting “Delete All” moves to step 5 and all songs are deleted. 4 Turn the [VOL] knob and press it when the desired item is displayed. Select the song you want to delete. 5 Turn the [VOL] knob and press it when the desired item is displayed. Select ”Yes”.
USB device Operation SRC MENU VOL 4 38 ¢ DISP SEARCH MODE When connecting the USB device, usage of the CA-U1EX (option) is recommended. / PLAY MODE Basic Operation File Search Playing USB device Selecting the file you want to listen to from the device being played now. • Connect a USB device When connected, the source is switched automatically and a song starts playing. USB device Display “Music” • Select USB source Press the [SRC] button.
1 ¡! USB Setting 2 You can select following USB Setting items. ¡" ¡# Cancelling Menu List mode Press the [MENU] button for at least 1 second, and then press it again briefly. ⁄ • When you search a song in the File Search mode, the unit memorizes the position of the song being played after the search. To set a different Menu item after searching a song, press the [MENU] button for at least 1 second to move to the first hierarchy.
USB device Operation Skip Search Function of remote control You can scroll up or down according to the number of the selected Search items so that you can quickly switch the display position. Searching the music by entering the file number. 1 2 Select USB source 3 Enter Skip Search mode Press the [SEARCH MODE] button. 4 Search for music Enter File Search mode Press the [MENU] button. Turn the [VOL] knob and press it when the desired item is displayed. Select “Music” > item.
Music CD/ Audio file Operation Release MENU VOL DISP SEARCH MODE Fast Forwards or Fast Backwards Hold down the [4] or [¢] button. ⁄ • No sound is output while playing audio file. SRC 4 38 ¢ /PLAY MODE Pause and Play Press the [38] button to pause or resume playback. Basic Operation Function of Internal CD source Drop open the faceplate Press the Release button. Selecting the music you want to listen to from the disc being played now.
Music CD/ Audio file Operation Play Mode “Track Repeat” You can select a Play Mode, such as Random play and Repeat play. “Disc Repeat” 1 2 Select CD source ( Enter Play Mode KDC-X994 KDC-BT945U Press the [VOL] knob for at least 1 second. KDC-X794 KDC-MP745U Press the [PLAY MODE] button. ✍✍You can also select from “Play Mode” in Menu List mode. 3 4 Make a setting Press the [4] or [¢] button. 5 Exit Play Mode Press the [MENU] button. KDC-X794 KDC-MP745U Press the [PLAY MODE] button.
Function of remote control Direct Music Search Searching the music by entering the track number. 1 Enter Direct Music Search mode Press the [DIRECT] button on the remote control. 2 Enter the music number Press the number buttons on the remote control. 3 Search the music Press the [4] or [¢] button. Cancelling Direct Music Search Press the [DIRECT] button. ⁄ • Direct Music Search cannot be performed during playing of Random play or scan play.
Tuner Operation “Auto Memory” SRC MENU VOL “TI” 4 “Forced MONO” ¢ Basic Operation Selecting Tuner source Press the [SRC] button. Turn the [VOL] knob and press it when the desired item is displayed. Select the “Tuner” display. ✍✍SRC Select mode 2: Pressing the [SRC] button repeatedly switches source. Selecting the Receiving Band 1. Enter Menu List mode Press the [MENU] button. 2. Turn the [VOL] knob and press it when the desired item is displayed. Select “FM1”, “FM2”, “FM3” or “AM”.
Station Preset Memory Preset Tuning Putting a station in the memory. Recalling the stations in the memory. 1 1 2 Select the radio band and tune in a desired radio station you wish to store in the preset memory 2 Enter Menu List mode Press the [MENU] button. 3 Enter Preset Memory mode Turn the [VOL] knob and press it when the desired item is displayed. Select “List & Memory”.
Tuner Operation Function of KDC-X994/KDC-X794 Function of KDC-X994/KDC-X794 PTY (Program Type) Program Type Preset Selecting the Program Type below and searching for a station. Putting the Program Type in the Preset button memory and quick recall.
Function of KDC-X994/ KDC-BT945U KDC-X794/ KDC-MP745U with BT200 (Optional Accessory) Bluetooth Audio Operation Basic Operation SRC MENU VOL 4 38 ¢ /PLAY MODE Selecting Bluetooth Audio source Press the [SRC] button. Turn the [VOL] knob and press it when the desired item is displayed. Select the “BT Audio” display. ✍✍SRC Select mode 2: Pressing the [SRC] button repeatedly switches source. Connecting a Bluetooth Device Pause and play Press the [38] button.
Function of KDC-X994/ KDC-BT945U KDC-X794/ KDC-MP745U with KCA-BT200 (Optional Accessory) Operation of hands-free phoning SRC MENU VOL ⁄ SEARCH MODE • When registering from this unit, refer to (page 49). • For details on the Bluetooth cell-phone with the handsfree function, see (page 63). 4 38 ¢ /PLAY MODE Connecting a Bluetooth Device Receiving a Call Answering a Phone Call Press the [VOL] knob.
Answering another Incoming Call after Terminating the Current Call Press the [SRC] button. below. 3 KDC-X994 KDC-BT945U Press the [ Continuing the Current Call 1 2 Answering the Waiting Call after Terminating the Current Call Press the [SRC] button. Switching between the Current Call and Waiting Call Press the [VOL] knob. Each pressing of this knob switches the calling party. Press the [PLAY MODE] button for at least 1 second.
Function of KDC-X994/ KDC-BT945U KDC-X794/ KDC-MP745U with KCA-BT200 (Optional Accessory) Operation of hands-free phoning Calling a Number in the Phone Book 1 3 Select a name or phone number Turn the [VOL] knob and press it when the desired item is displayed. ✍✍Switching between Display Modes Press the [DISP] button. Pressing this button each time switches between name and telephone number. 4 Make a call Press the [VOL] knob. Enter Bluetooth mode KDC-X994 KDC-BT945U Press the [ ] button.
Function of KDC-X794/ KDC-MP745U Make a Voice Dialing Call Registering to the Preset Dial Number List 1 Enter voice recognition mode Press the [VOL] knob for at least 1 second. 1 2 “PB Name?” is displayed. When a beep is heard, say the name within 2 seconds. Select the phone number you wish to register Select the phone number with reference to the following: - Calling a Number in the Phone Book (page 26) - Calling a Number in the Call log (page 26) 3 “PN Type” is displayed.
Display Settings SRC MENU VOL Display Setting You can select following Display Setting items. 4 Select the source Press the [SRC] button. Turn the [VOL] knob and press it when the desired item is displayed. ✍✍SRC Select mode 2: Pressing the [SRC] button repeatedly switches source. 2 Enter Menu List mode Press the [MENU] button. 3 Enter Display Setting mode Turn the [VOL] knob and press it when the desired item is displayed. Select “Settings” > “DISP & ILLUMI”.
“ILLUMI Effect” Sets whether the key illumination brightness is changed in conjunction with the key operation. “OFF”/ “ON” “ILLUMI MSC Sets whether the key illumination color is SYNC” changed in conjunction with the sound volume. (KDC-X994 only) “OFF”/ “ON” ( : Factory setting) 5 Make a setting • When the “ PUSH ” icon is displayed (at the right edge of the display) Turn the [VOL] knob to select a setting value, and then press the [VOL] knob.
Display Settings Customization of 5-line Display Mode & 3-line Display Mode & iPod-like Display Mode You can customize the display of the 5-line display mode, 3-line display mode, and iPod-like display mode. 1 Select the source Press the [SRC] button. Turn the [VOL] knob and press it when the desired item is displayed. ✍✍SRC Select mode 2: Pressing the [SRC] button repeatedly switches source. 2 Enter Menu List mode Press the [MENU] button.
In SIRIUS/ SAT/ XM source (Optional) In Music CD source Disc title (“Disc title”) Track title (“Track title”) Play time (“P-Time”) Spectrum analyzer & Clock (“Speana/Clock”) Date (“Date”) Blank (“Blank”) In Auxiliary input source Source name (“Source Name”) Spectrum analyzer & Clock (“Speana/Clock”) Date (“Date”) Blank (“Blank”) In Standby Source name (“Source Name”) Date (“Date”) 5-line display mode Spectrum analyzer & Clock (“Speana/Clock”) Date (“Date”) Blank (“Blank”) 3-line display mode Bluetoot
Display Settings Customization of Spectrum Analyzer Display Mode Function of KDC-X994 You can customize the display of the Spectrum analyzer display mode. Selecting the Illumination Color of the panel. 1 Select the source Press the [SRC] button. Turn the [VOL] knob and press it when the desired item is displayed. ✍✍SRC Select mode 2: Pressing the [SRC] button repeatedly switches source. 2 Enter Menu List mode Press the [MENU] button.
Auxiliary Input Display Setting Selecting the display when changing to Auxiliary input source. 1 Select the AUX source Press the [SRC] button. Turn the [VOL] knob and press it when the desired item is displayed. Select the “AUX” display. ✍✍SRC Select mode 2: Pressing the [SRC] button repeatedly switches source. 2 Enter Menu List mode Press the [MENU] button. 3 Enter Auxiliary input display setting mode Turn the [VOL] knob and press it when the desired item is displayed.
Clock and Other Functions Release 2. Press the [¢] button. 3. Turn the [VOL] knob to adjust the month. 4. Press the [¢] button. 5. Turn the [VOL] knob to adjust the day. 6. Press the [VOL] knob. MENU VOL SRC 4 7 Enter Date format mode Turn the [VOL] knob and press it when the desired item is displayed. Select “Date Mode Select”. 8 Select Date format Turn the [VOL] knob and press it when the desired item is displayed. Select from 7 types.
“Built in AUX” hen this is set to ON, AUX source can be W selected. “ON”: Allows AUX source to be selected. Use this setting when the built-in AUX terminal is connected to the external equipment all the time. “OFF”: Disable AUX source selection. Use this setting when the built-in AUX terminal is not used. “Forced CD-DA” Sets the method for reading CD. “Settings 1”: Automatically distinguishes between audio file disc and music CD when playing disc. “Settings 2”: Forces playing as music CD.
Clock and Other Functions Theft Deterrent Faceplate The faceplate of the unit can be detached and taken with you, helping to deter theft. Removing the Faceplate 1 Press the Release button. Drop open the faceplate. 2 Drawing the faceplate to left side pull it to forward and remove it. ¤ • The faceplate is a precision piece of equipment and can be damaged by shocks or jolts. • Keep the faceplate in its faceplate case while detached.
English | 37
Audio Adjustments “2Zone” “2Zone Select” “Preset” SRC MENU VOL Sets the Dual Zone System. - Dual Zone System (page 40). Sets the audio preset. - Audio Preset Memory (page 44). - Audio Preset Recall (page 45). ( 4 ¢ Select the source Press the [SRC] button. Turn the [VOL] knob and press it when the desired item is displayed. Select a source other than “STANDBY”. ✍✍SRC Select mode 2: Pressing the [SRC] button repeatedly switches source. 2 Enter Audio Control mode Press the [VOL] knob.
Preset Equalizer curve Select Manual Equalizer Control You can select following Equalizer curve. You can adjust following Equalizer Control items. Display “Natural” “User” “Rock” “Pops” “Easy” “Top 40” “Jazz” “Game” “iPod” KDC-X994/ KDC-X794 Band Item “BAND1” (62.
Audio Adjustments 4 Listening Position Selection The sound environment can be compensated in accordance with the selected position. According to the listening position, select the position from the following settings. Compensation seat Not compensating.
desired item is displayed. 5 Exit Audio Control mode Press the [MENU] button for at least 1 second, and then press it again briefly. ⁄ • • • • Select Main source by [SRC] button. Adjust the volume of Front channel by [VOL] knob. The Audio Control has no effect on sub source. There are following limitations when Dual Zone System is enabled. - There is no output from the subwoofer. - “Fader”, “Subwoofer Level” of
DSP Setup Speaker Setting SRC MENU VOL The speaker X’Over is automatically set when the position and size of each speaker are selected from the following items. Speaker “FRONT” 4 ¢ Car Type Selection You can compensate the delay of the sound arrival time by selecting your environment from the following car types. Display “OFF” “Compact” “Full size car” “Wagon” “Minivan” “SUV” “Minivan (Long)” Overview Not compensating.
5 Exit Audio Control mode Press the [MENU] button for at least 1 second, and then press it again briefly. Reference point +3.2 feet Car Type Fine Adjustments FRONT 1.7 feet Adjusting fine tuning of the speaker position compensation value specified at (page 42). Display “Front” “Rear” “SW” Item Front speaker Rear speaker Subwoofer Select the source Press the [SRC] button. Turn the [VOL] knob and press it when the desired item is displayed. Select a source other than “STANDBY”.
DSP Setup X’Over Setting 6 Fine adjusting the following setting values corresponding to the X’Over values set in the section (page 42). Repeat steps 3 to 4 to complete the X’Over settings. 7 Exit Audio Control mode Press the [MENU] button for at least 1 second, and then press it again briefly.
Audio Preset Recall Recalling the sound setup registered by
Favorite Control • If the contents in iPod are changed after the FAVORITE registration, the list registered in this unit becomes different from that in iPod. In this case, perform the FAVORITE registration again. MENU VOL Favorite Preset Recall FAV Favorite Preset Memory Registering the operation procedure to select your favorite broadcast station or iPod Playlists/ Artists, etc.
Select “YES”. “Completed” is displayed. Exit Favorite Preset Memory Delete mode.
Function of KDC-X994/ KDC-BT945U KDC-X794/ KDC-MP745U with KCA-BT200 (Optional Accessory) Bluetooth Setup “PIN Code Edit” Specify the PIN code required when registering this unit using the Bluetooth device. Refer to (page 50). “Auto Answer” Answer a call automatically after lapse of the preset time interval for automatic answer. “OFF”/ “0s” – “8s” – “99s” “Bluetooth HF/ You can specify output speakers for hands-free Audio” voice communication and Bluetooth audio sound.
“1s” – “99s” : Automatically answers the phone call after lapse of 1 – 99 seconds. 6 Transmit the PIN code Press the [VOL] knob for at least 1 second. If “Pairing Success” is displayed, registration is completed. ✍✍If the error message appears even though the PIN code is correct, try . 7 Return to the device list Press the [MENU] button. 8 Exit BT Settings mode ⁄ • If the time set in the cell-phone is shorter than that set in the unit, the former will be used.
Function of KDC-X994/ KDC-BT945U KDC-X794/ KDC-MP745U with KCA-BT200 (Optional Accessory) Bluetooth Setup Registering PIN Code By operating the Bluetooth device, specify the PIN code necessary for registering this unit. 1 Enter Bluetooth mode KDC-X994 KDC-BT945U Press the [ ] button. KDC-X794 KDC-MP745U Selecting the Bluetooth device You Wish to Connect When two or more Bluetooth devices have already been registered, you need to select the Bluetooth device you wish to use.
Deleting a Registered Bluetooth device You can delete a registered Bluetooth device. 1 Enter Bluetooth mode KDC-X994 KDC-BT945U Press the [ ] button. KDC-X794 KDC-MP745U Press the [PLAY MODE] button for at least 1 second. ✍✍You can also select from “Settings” in Menu List mode. 2 Enter Bluetooth device deletion mode Turn the [VOL] knob and press it when the desired item is displayed. Select “BT Settings” > “Detailed Setup” > “Device Delete”. “(name)” is displayed.
Function of KDC-X994/ KDC-BT945U KDC-X794/ KDC-MP745U with KCA-BT200 (Optional Accessory) Bluetooth Setup Function of KDC-X794/KDC-MP745U Select “PB Name Check” (Play) Adding a Voice Dialing Command 5 Add a voice tag to the phone book for voice dialing. You can register up to 35 voice tags. Select “PB Name Delete” (Delete) 1 5 Delete a voice tag Press the [VOL] knob. 6 Turn the [VOL] knob to select “YES”, and then press the [VOL] knob.
6 Exit BT Settings mode Press the [PLAY MODE] button for at least 1 second. ⁄ • Set the voice tag for all the 5 categories. If the voice tag is not registered for all the categories, the Phone book may not be recalled by voice command.
Function of KDC-X994/ KDC-BT945U KDC-X794/ KDC-MP745U with KCA-BT200 (Optional Accessory) SMS (Short Message Service) Downloading the SMS SMS (Short Message Service) Download the short message (SMS) arrived at the cell-phone so that it can be read on this unit. The SMS arrived at the cell-phone is displayed on the receiver. A newly arrived message is displayed. 1 Enter Bluetooth mode KDC-X994 KDC-BT945U Press the [ ] button.
linked with Bluetooth cannot be displayed. Download the SMS. • The short message cannot be displayed during downloading the SMS.
Satellite Radio Tuner Control (Optional) SRC MENU VOL Satellite Radio Setting You can select following Satellite Radio Setting items. 4 ¢ 1 2 Select Satellite Radio source 3 Turn the [VOL] knob and press it when the desired item is displayed. Select “Settings”. 4 Select the setting item to adjust Turn the [VOL] knob and press it when the desired item is displayed. Basic Operation Selecting Satellite Radio source Press the [SRC] button.
Press the [MENU] button for at least 1 second, and then press it again briefly. 3 Enter Channel Scan Turn the [VOL] knob and press it when the desired item is displayed. Select “Channel Scan”. 4 Start Channel Scan Turn the [VOL] knob and press it when the desired item is displayed. Select “YES”. 5 Release it when the channel you want to listen to is received Press the [VOL] knob. ⁄ • You cannot Channel search until the category information is acquired.
HD Radio™ Tuner Control (Optional) SRC MENU VOL SEARCH MODE Cancelling the Preset Memory mode Press the [MENU] button for at least 1 second, and then press it again briefly. Auto Memory Entry 4 ¢ Basic Operation Selecting HD Radio source Press the [SRC] button. Turn the [VOL] knob and press it when the desired item is displayed. Select the “HD RADIO” display. ✍✍SRC Select mode 2: Pressing the [SRC] button repeatedly switches source. Selecting the Receiving Band 1.
Display “Settings” “Seek Mode” “Auto Memory” “Receive Mode” “TAG Memory” “Tagging” Overview Selects the tuning mode of the radio. “Auto1”: Automatic search for a station. “Auto2”: Search in order of the stations in the Preset memory. “Manual”: Normal manual tuning control. Memorizes 6 stations with good reception automatically. Refer to (page 58) Sets the receive mode of the HD Radio receiver. “Auto”: Automatically tunes to analog broadcast when there is no digital broadcast.
Basic Operations of remote control In Tuner/HD Radio source VOL SRC • Band select: [FM]/[AM] • Station select: [4]/[¢] • Recall preset stations: [1] — [6] ATT ENT 5/∞ EXIT AUD AM FM 0—9 DIRECT (page 16, 19, 21, 26, 57, 59) General control • Volume control: [VOL] • Source select: [SRC] • Volume reduce: [ATT] When the button is pressed again, the volume returns to the previous level.
Hands-free phone control Preparing the remote control unit Making a call • Enter Bluetooth mode: [ ] • Select a dialing method: [5]/[∞] ➜ [ENT] • Number dial input: Input a digit: [0] – [9] Input “+”: [¢] Input “#”: [FM] Input “*”: [AM] Clear the entered phone number: [4] • Make a call: [DIRECT] Pull the battery sheet out from the remote control unit to the direction of the arrow.
Appendix About Audio file • Playable Audio file AAC-LC (.m4a), MP3 (.mp3), WMA (.wma) • Playable disc media CD-R/RW/ROM • Playable disc file format ISO 9660 Level 1/2, Joliet, Romeo, Long file name. • Playable USB device USB mass storage class • Playable USB device file system FAT16, FAT32 Although the audio files are complied with the standards listed above, the play maybe impossible depending on the types or conditions of media or device.
• When connecting the USB device, usage of the CA-U1EX (option) is recommended. Normal playback is not guaranteed when a cable other than the USB compatible cable is used. Connecting a cable whose total length is longer than 5 m can result in abnormal playback. About “KENWOOD Music Editor” • This unit supports the PC application “KENWOOD Music Editor Lite ver1.0” or later. • When you use the audio file with database information added by the “KENWOOD Music Editor Lite ver1.
Appendix Menu List Common function items Display “Settings” “Clock & Date” “Clock Adjust” “Time Syncronized” “Date Adjust” “Date Mode Select” “DISP & ILLUMI” “Display Select” “Type Select” “Side Select” “Graphic Select” “Text Select” “Status” “Color Select” “Display Off Mode” “Display Dimmer” “Contrast” “DISP N/P” “TEXT Scroll” “ILLUMI Dimmer” “ILLUMI Effect” “ILLUMI MSC SYNC” “RDS Settings” “TI” “DEMO Mode” Page – 34 – – 30, 32 30 32 30 32 28 – 20 35 Function items appearing during standby Display Page
Function items appearing when the Music CD/ Audio file source is selected Display Page “Music” 19 “Play Mode” 18 “File Scan” “Track Scan” “Folder Random” “Disc Random” “Magazine Random” “File Repeat” “Folder Repeat” “Track Repeat” “Disc Repeat” “Settings” – “Clock & Date” – “DISP & ILLUMI” – “RDS Settings” – Function items appearing when the Tuner source is selected Display Page “List & Memory” 21, 21 “FM1” 20 “FM2” “FM3” “AM” “PTY Search” 22 “Settings” – “Seek Mode” 20 “Auto Memory” 21 “TI” 20 “Forced MONO
Appendix Function items appearing when the Satellite Radio tuner source is selected Display Page “List & Memory” 57, 57 “SR1”/ “XM1” 56 “SR2”/ “XM2” “SR3”/ “XM3” “SR4”/ “XM4” “Channel Search” 56 “Channel Scan” 57 “Settings” – “Seek Mode” 56 “ESN” “Clock & Date” – “DISP & ILLUMI” – “RDS Settings” – Function items appearing when the HD Radio™ tuner source is selected Display Page “List & Memory” 58, 58 “FM1” 58 “FM2” “FM3” “AM” “Settings” – “Seek Mode” 58 “Auto Memory” 58 “Receive Mode” 58 “TAG Memory” “Taggi
English | 67
Appendix 2CAUTION IC (Industry Canada) Notice Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. In compliance with Federal Regulations, following are reproductions of labels on, or inside the product relating to laser product safety.
Accessories/ Installation Procedure Accessories 2 1 ..........2 ..........1 3 4 ..........4 ..........4 5* 3 m (9.5 ft) ..........1 *Accessory of KDC-X994/ KDC-BT945U Installation Procedure 1 To prevent a short circuit, remove the key from the 2 3 4 5 6 7 8 ignition and disconnect the - battery. Make the proper input and output wire connections for each unit. Connect the speaker wires of the wiring harness. Connect the wiring harness wires in the following order: ground, battery, ignition.
Connecting Wires to Terminals not remove the cap ⁄ Do when you do not use the To USB device USB connector (1m) R USB cable. The connector will cause the unit to malfunction if it gets in touch with any metallic part of the vehicle. Microphone input (KDC-X994 / KDC-BT945Uonly) L Rear output Front output Sub Woofer output Antenna Cord Microphone (Accessory5) FM/AM antenna input L R AUX input (Stereo) Use the mini-plug which is stereo type and does not have any resistance.
Installation/Removing the Unit non-Japanese cars Removing the hard rubber frame 1 Engage the catch pins on the removal tool and remove the two locks on the upper level. Upper the frame and pull it forward as shown in the figure. Lock Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place. Accessory2 Removal tool ⁄ • Make sure that the unit is installed securely in place. If the unit is unstable, it may malfunction (for example, the sound may skip).
Installation/Removing the Unit Accessory of KDC-X994/ KDC-BT945U Installation the Microphone Unit 1 Check the installation position of the microphone 2 3 4 (accessory 5). Remove oil and other dirt from the installation surface. Install the microphone. Wire the cable up to the unit with it secured at several positions using tape or the like. Accessory 5 Fix a cable with a commercial item of tape. Peel the release coated paper of double-face adhesive tape to fix on the place shown above.
Troubleshooting Guide Some functions of this unit may be disabled by some settings made on this unit. ! ! ! • Cannot set up the subwoofer. • No output from the subwoofer. • Cannot set up the subwoofer position of Manual position setting. ▲ • The Dual zone function is enabled. (page 40) • In the speaker select option, None is selected for the subwoofer. (page 42) • Cannot set up the equalizer. • Cannot set up the Bass Boost.
Troubleshooting Guide Hands-free ? The hands-free talk volume is low. The hands-free talk volume is set at a low level. The hands-free talk volume can be adjusted independently. Adjust it during hands-free talk. “Mic Gain” and “NR Level” (page 48). ? No sound is heard from the rear speakers. You are talking in the hand-free talk mode. No sound is heard from the rear speakers in the hands-free talk mode. ? No beep is heard at reception of an incoming call.
N/A Device: • An unsupported USB device is connected. • Connection to the iPod has failed. Check that the connected iPod is an iPod that is supported. See (page 62) for information on supported iPods. Err No Matching: The voice tag is wrong. Voice cannot be recognized because of an unregistered voice tag, etc. Too Soft: Voice is too small and cannot be recognized. No Music Data/Error 15: • The connected USB device contains no playable audio file.
Specifications FM tuner section Frequency range (200 kHz space) : 87.9 MHz – 107.9 MHz Usable sensitivity (S/N = 30dB) : 9.3dBf (0.8 μV/75 Ω) Quieting Sensitivity (S/N = 50dB) : 15.2dBf (1.6 μV/75 Ω) Frequency response (±3 dB) : 30 Hz – 15 kHz Signal to Noise ratio (MONO) : 70 dB Selectivity (±400 kHz) : ≥ 80 dB Stereo separation (1 kHz) : 40 dB USB Interface USB Standard : USB1.1/ 2.
Audio section Maximum output power : 50 W x 4 Full Bandwidth Power (at less than 1% THD) : 22 W x 4 Speaker Impedance : 4 – 8 Ω Tone action (KDC-X994/KDC-X794) BAND1 (60 Hz): ±9 dB BAND2 (250 Hz): ±9 dB BAND3 (1 kHz): ±9 dB BAND4 (4 kHz): ±9 dB BAND5 (16 kHz): ±9 dB Tone action (KDC-BT945U/KDC-MP745U) BAND1 : 60 Hz - 400 Hz ±9 dB BAND2 : 630 Hz - 2.5 kHz ±9 dB BAND3 : 4.
This symbol mark indicates that Kenwood manufactured this product so as to decrease harmful influence on the environment.
KDC-X994 KDC-BT945U KDC-X794 KDC-MP745U CD-RECEIVER Quick Start Guide AMPLI-TUNER LECTEUR DE CD Guide de démarrage rapide REPRODUCTOR DE DISCOS COMPACTOS RECEPTOR DE FM/AM Guía de inicio rápido © B59-2009-00/00 (KW)
Contents About the Quick Start Guide............... 2 Before use .................................................. 3 First step ..................................................... 4 Basic Operations ...................................... 5 Playing Music (CD/USB/iPod).............. 6 Listening to the Radio ........................... 8 Hands-free phoning ............................... 9 Accessories ..............................................10 Installation Procedure .........................
Before use 2WARNING To prevent injury or fire, take the following precautions: To prevent a short circuit, never put or leave any metallic objects (such as coins or metal tools) inside the unit. How to reset your unit If this unit or the Reset button connected unit (auto disc changer, etc.) fails to operate properly, press the Reset button. The unit returns to factory settings when the Reset button is pressed.
First step [MENU] [4] [¢] Exit Demonstration Mode 5 Press the [MENU] button to finish the clock adjusting. 6 Press the [VOL] knob to quit the demonstration mode when the messages “To Cancel Demo Press the volume knob” are displayed (approx. 15 seconds). Turn the [VOL] knob to select “Date Adjust”, and then press the [VOL] knob. 7 Press [4] or [¢] button to select year, month, or date to set. 8 Turn the [VOL] knob to adjust the year, month, and date.
Basic Operations [SRC] [VOL] AUX AUX Auxiliary input USB Terminal Power Turns the power ON by pressing the [SRC] button. Press the [SRC] button for at least 1 second to turn the power OFF. Source selection Press the [SRC] button and then turn the [VOL] knob. To determine the selected source, press the [VOL] knob. Tuner (“TUNER” or “HD RADIO”) ➜ Bluetooth Audio (“BT AUDIO”) (KDC-X994, KDC-BT945U only) ➜ USB (“USB”) or iPod (“iPod”) ➜ CD (“CD”) ➜ Auxiliary Input (“AUX”) ➜ Standby (“STANDBY”) ➜ Tuner...
Playing Music (CD/USB/iPod) [MENU] [DISP] [Release] [SRC] [4] [38] [ [VOL] KDC-X994 KDC-BT945U ] [SEARCH MODE] [¢] USB Terminal KDC-X794 KDC-MP745U [PLAY MODE] Playing Disc Fast Forward or Fast Backward of Press the [Release] button and drop the Song open the faceplate. Insert the disc in the Disc slot. When inserted, the source is switched automatically and a song starts playing. Push the faceplate on the left side, and return it to its former position.
Music Search Searching for the song you want to play. 1 2 3 Press the [MENU] button. Turn the [VOL] knob to select “Music”, and then press the [VOL] knob. Search for music. Operation type Move between items Select an item High Speed Search Operation Turn the [VOL] knob. Press the [VOL] knob. Press the [DISP] or [ ] / [PLAY MODE] button to scroll up or down by a page. Press the [DISP] or [ ] / [PLAY MODE] button for at least 1 second to continuously scroll up or down at high speed.
Listening to the Radio [SRC] [MENU] [4] [VOL] [¢] Selecting a Tuner source 1 2 Press the [SRC] button. Turn the [VOL] knob to select “TUNER”, and then press the [VOL] knob. Selecting the Band 1 2 Press the [MENU] button. Turn the [VOL] knob to select desired band (“FM1”, “FM2”, “FM3”, or “AM”), and then press the [VOL] knob. Selecting a Station Press the [4] or [¢] button to select the station you want to listen to.
Function of KDC-X994/ KDC-BT945U/ KCA-BT200 (Optional Accessory) Hands-free phoning [SRC] [VOL] KDC-X994 KDC-BT945U [ ] KDC-X794 KDC-MP745U [PLAY MODE] Registering cellphone Calling a number in the Phone Register your Bluetooth cellphone in this Book unit. 1 By operating the cellphone, register the hands-free unit (pairing). Select “KENWOOD BT CD/R-4P1” or “KCA-BT200” from the list of connected units. 2 Enter the PIN code of this unit from the cellphone.
Accessories Before Installation 2WARNING 1 .....1 2 .....2 3 .....4 4 .....4 5(KDC-X994 / KDC-BT945Uonly) .....1 (9.5 ft) Installation Procedure 1. To prevent a short circuit, remove the key from the ignition and disconnect the battery. 2. Make the proper input and output wire connections for each unit. 3. Connect the speaker wires of the wiring harness. 4. Connect the wiring harness wires in the following order: ground, battery, ignition. 5. Connect the wiring harness connector to the unit. 6.
• • • • • tape or other similar material. To prevent a short circuit, do not remove the caps on the ends of the unconnected wires or the terminals. Connect the speaker wires correctly to the terminals to which they correspond. The unit may be damaged or fail to work if you share the - wires or ground them to any metal part in the car.
Connecting Wires to Terminals not remove the cap when you ⁄ Do do not use the USB cable. The connector will cause the unit to malfunction if it gets in touch with any metallic part of the vehicle.
R L Rear output Front output Sub Woofer output Fuse (10A) FM/AM antenna input R AUX input (Stereo) Use the mini-plug which is stereo type and does not have any resistance. L To Kenwood disc changer/ External optional accessory To connect these leads, refer to the relevant instruction manuals. Wiring harness (Accessory1) ⁄ If no connections are made, do not let the wire come out from the tab. Power control wire (Blue/White) P.CONT Motor antenna control wire (Blue) ANT.
Installation/Removing the Unit non-Japanese cars Removing the hard rubber frame 1. Engage the catch pins on the removal tool and remove the two locks on the upper level. Lift up and pull the frame forward as shown in the figure. Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place. Lock Catch Removal tool (Accessory2) ⁄ • Make sure that the unit is installed securely in place. If the unit is unstable, it may malfunction (for example, the sound may skip).
KDC-X994/ KDC-BT945U only Installation the Microphone Unit Removing the hard rubber frame 1. Check the installation position of the microphone (accessory 5). 2. Remove oil and other dirt from the installation surface. 3. Install the microphone. 4. Wire the cable up to the unit with it secured at several positions using tape or the like. Accessory5 ⁄ • Install the microphone as far as possible from the cell-phone. Fix a cable with a commercial item of tape.
2CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. In compliance with Federal Regulations, following are reproductions of labels on, or inside the product relating to laser product safety. Kenwood Corporation 2967-3, ISHIKAWA-MACHI, HACHIOJI-SHI TOKYO, JAPAN KENWOOD CORP. CERTIFIES THIS EQUIPMENT CONFORMS TO DHHS REGULATIONS N0.21 CFR 1040. 10, CHAPTER 1, SUBCHAPTER J.
• HD Radio™ and the HD Radio Ready logo are proprietary trademarks of iBiquity Digital Corporation. • The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Kenwood Corporation is under license. Other trademarks and trade names are those of their respective owners. • The “AAC” logo is trademark of Dolby Laboratories. • iPod is a trademark of Apple Inc., registered in the U.S. and other countries. • iPhone is a trademark of Apple Inc.
This symbol mark indicates that Kenwood manufactured this product so as to decrease harmful influence on the environment.
KENWOOD KDC-X994/ KDC-X794 / KDC-BT945U KDC-MP745U / KDC-BT60U / KDC-6047U Ver.1.0 W01-1778-0S INSTRUCTION MANUAL MODE D' EMPLOI ~HCTPYKC~51 no 3Kcn.nYATAu.~~ This CD-ROM (Data) cannot be played on an audio CD player.
