KDC-105U KDC-MP105U CD-RECEIVER INSTRUCTION MANUAL AMPLI-TUNER LECTEUR DE CD MODE D’EMPLOI REPRODUCTOR DE DISCOS COMPACTOS RECEPTOR DE FM/AM MANUAL DE INSTRUCCIONES Take the time to read through this instruction manual. Familiarity with installation and operation procedures will help you obtain the best performance from your new CD-receiver. For your records Record the serial number, found on the back of the unit, in the spaces designated on the warranty card, and in the space provided below.
CONTENTS BEFORE USE BEFORE USE 2 Warning BASICS 3 Do not operate any function that takes your attention away from safe driving. GETTING STARTED 4 Caution RADIO 5 CD / USB 6 AUX 7 DISPLAY SETTINGS 7 AUDIO SETTINGS 8 MORE INFORMATION 8 TROUBLESHOOTING 9 SPECIFICATIONS 9 INSTALLATION / CONNECTION 10 Volume setting: • Adjust the volume so that you can hear sounds outside the car to prevent accident.
BASICS Faceplate Remote control (RC-406) Remote sensor (Do not expose to bright sunlight.) Attach Volume knob (turn/press) Loading slot Detach Pull out the insulation sheet when using for the first time. * Not used. How to reset Detach button Display window How to replace the battery Your preset adjustments will also be erased. To Do this (on the faceplate) Do this (on the remote control) Turn on the power Press L SRC. • Press and hold to turn off the power.
GETTING STARTED 3 Set the initial settings 1 2 3 4 1 Cancel the demonstration When you turn on the power (or after you reset the unit), the display shows: “CANCEL” \ “DEMO” \ “PRESS” \ “VOLUME” \ “KNOB” 1 Press the volume knob. Press SRC to enter [STANDBY]. Press the volume knob to enter [FUNCTION]. Turn the volume knob to select [INITIAL], then press the knob. Turn the volume knob to make a selection (see the table below), then press the knob. 5 Press and hold to exit.
RADIO Default: XX Search for a station 1 Press L SRC to select TUNER. 2 Press repeatedly (or press *AM– / #FM+ on RC-406) to select FM1/ FM2/ FM3/ AM. “F1” / “F2” / “F3” / “AM” appears on the display. 3 Press 4 / ¢ to search for a station. • To store a station: Press and hold one of the number buttons (1 to 6). • To select a stored station: Press one of the number buttons (1 to 6) Direct Access Tuning (using RC-406) 1 Press *AM– / #FM+ to select a band. 2 Press DIRECT to enter Direct Access Tuning.
CD / USB Start playback CD Label side 0: Eject disc : Applicable — : Not applicable The source changes to CD and playback starts. USB USB input terminal CA-U1EX (max.: 500 mA) (optional accessory) To Do this Pause or resume playback Press 6 38 (or ENT 38 on RC-406). Select a track/file Press 4 / ¢ (or 4 / ¢ (+) on RC-406). Select a folder Press 1 – / 2 + (or *AM– / #FM+ on RC-406). Reverse/Fast-forward Press and hold 4 / ¢ (or 4 / ¢ (+) on RC-406).
CD / USB Direct Music Search (using RC-406) 1 Press DIRECT. 2 Press the number buttons to enter a track/file number. 3 Press 4 / ¢ (+) to search for music. • To cancel, press . • Not available if Random Play is selected. • Not applicable for KME Light/ KMC file. (➜ 8) AUX DISPLAY SETTINGS Preparation: Select [AUX ON] for [AUX SET]. (➜ 4) 1 Press the volume knob to enter [FUNCTION]. 2 Turn the volume knob to select [SETTINGS], then press the knob.
AUDIO SETTINGS MORE INFORMATION While listening to any source... 1 Press AUDIO to select [AUD CTRL]. 2 Turn the volume knob to make a selection (see the table below), then press the knob. Repeat step 2 until the desired item is selected or activated. 3 Press and hold to exit. • To return to the previous hierarchy, press . Default: XX SW LEVEL –15 to +15 (0): BASS LVL –8 to +8 (0): MID LVL –8 to +8 (0): Adjusts the subwoofer output level. Adjusts the level to memorize for each source.
“READ ERR” appears. “NO DVICE” appears. “COPY PRO” appears. “NO MUSIC” appears. “NA DVICE” appears. “USB ERR” appears. Noise is generated. Tracks do not play back as you have intended them to play. “READING” keeps flashing. Elapsed playing time is not correct. Correct characters are not displayed (e.g. album name). EN_KDC-105U[K0]f.indd 9 Make sure the disc contains supported audio files. (➜ 8) Insert a playable disc into the loading slot. Make sure the disc is clean and inserted properly. Reset the unit.
INSTALLATION / CONNECTION Installating the unit (in-dash mounting) Warning • The unit can only be used with a 12 V DC power supply, negative ground. • Disconnect the battery’s negative terminal before wiring and mounting. • Do not connect Battery wire (yellow) and Ignition wire (red) to the car chassis or Ground wire (black) to prevent a short circuit. • Insulate unconnected wires with vinyl tape to prevent a short circuit. • Be sure to ground this unit to the car’s chassis again after installation.
Wiring connection REAR/SW R Part list for installation KDC-MP105U L Rear/subwoofer output R FRONT REAR/SW KDC-105U L A Faceplate Front output Rear/subwoofer output ( ×1 ) Fuse (10 A) Antenna terminal B Mounting sleeve If no connections are made, do not let the wire come out from the tab.
TABLE DES MATIERES AVANT L’UTILISATION AVANT L’UTILISATION 2 Avertissement FONCTIONNEMENT DE BASE 3 N’utilisez aucune fonction qui risque de vous distraire de la conduite sure de votre véhicule.
FONCTIONNEMENT DE BASE Façade Télécommande (RC-406) Capteur de télécommande (NE l’exposez PAS à la lumière directe du soleil.) Attachez Bouton de volume (tournez/appuyez) Fente d’insertion Détachez Retirez la feuille d’isolant lors de la première utilisation. * Non utilisé. Comment réinitialiser Touche de détachement Fenêtre d’affichage Comment remplacer la pile Vos ajustements préréglés sont aussi effacés.
PRISE EN MAIN 3 Faites les réglages initiaux 1 Appuyez sur SRC pour entrer en veille [STANDBY]. 2 Appuyez sur le bouton de volume pour entrer [FUNCTION]. 3 Tournez le bouton de volume pour choisir [INITIAL], puis appuyez sur le bouton.
RADIO Défaut: XX Recherchez une station 1 Appuyez sur L SRC pour choisir TUNER. 2 Appuyez répétitivement sur (ou appuyez sur *AM– / #FM+ sur la RC-406) pour sélectionner FM1/ FM2/ FM3/ AM. “F1” / “F2” / “F3” / “AM” apparaît sur l’affichage. 3 Appuyez sur 4 / ¢ pour recherche une station. • Pour mémoriser une station: Maintenez pressée une des touches • numériques (1 à 6). Pour choisir une station mémorisée: Appuyez sur l’une des touches numériques (1 à 6).
CD / USB Démarrez la lecture Face portant l’étiquette CD 0: Éjectiez le disque : Applicable — : Non applicable Pour La source change sur CD et la lecture démarre. USB Prise d’entrée USB CA-U1EX (max.: 500 mA) (accessoire en option) La source change sur USB et la lecture démarre. Faire Appuyez sur 6 38 (ou ENT 38 sur la RC-406). Mettez en pause ou reprenez la lecture Sélectionnez un une plage ou un fichier Appuyez sur 4 / ¢ (ou 4 / ¢ (+) sur la RC-406).
CD/USB Recherche directe de morceau (en utilisant la RC-406) 1 Appuyez sur DIRECT. 2 A l’aide des touches numériques, entrez le numéro de plage/fichier. 3 Appuyez sur 4 / ¢ (+) pour rechercher un morceau. AUX RÉGLAGES D’AFFICHAGE Préparation: Sélectionnez [AUX ON] pour [AUX SET]. (➜ 4) 1 Appuyez sur le bouton de volume pour entrer Lors de l’écoute d’un fichier KME Light/ KMC... 1 Appuyez sur le bouton de volume pour entrer 2 3 4 5 [FUNCTION].
RÉGLAGES AUDIO PLUS D’INFORMATIONS Pendant l’écoute de n’importe quelle source... 1 Appuyez sur AUDIO pour choisir [AUD CTRL]. 2 Tournez le bouton de volume pour réaliser une sélection (voir le tableau ci-dessous), puis appuyez sur le bouton. Répétez l’étape 2 jusqu’à ce que l’élément souhaité soit sélectionné ou activé. 3 Maintenez enfoncée pour quitter.
FR_KDC-105U[K0].indd 9 Tuner Lecteur CD USB • Le son ne peut pas être entendu. • L’appareil ne se met pas sous tension. • L’information affichée sur l’afficheur est incorrecte. Cet autoradio ne fonctionne pas du Réinitialisez l’appareil. (➜ 3) tout. • La réception radio est mauvaise. • Connectez l’antenne solidement. • Bruit statique pendant l’écoute de la • Sortez l’antenne complètement. radio. “NA FILE” apparaît. Assurez-vous que le disque contient des fichiers audio compatibles.
INSTALLATION / RACCORDEMENT Installation de l’appareil (montage encastré) Avertissement • L’appareil peut uniquement être utilisé avec une alimentation de 12 V CC, à masse négative. • Déconnectez la borne négative de la batterie avant le câblage et le montage. • Ne connectez pas le fil de batterie (jaune) et le fil d’allumage (rouge) au châssis de la voiture ou au fil de masse (noir) pour éviter les courts-circuits. • Isolez les fils non connectés avec du ruban adhésif pour éviter les courtscircuits.
Connexions REAR/SW R L KDC-MP105U Sortie arrière/caisson de grave FRONT REAR/SW KDC-105U R Liste des pièces pour l’installation L A Façade Sortie avant Sortie arrière/caisson de grave ( ×1 ) Fusible (10 A) Borne de l’antenne B Manchon de montage Si aucune connexion n’est faite, ne laissez pas le câble sortir de la languette.
CONTENIDO ANTES DEL USO ANTES DEL USO 2 Advertencia PUNTOS BÁSICOS 3 No utilice ninguna función que pueda desviar su atención mientras está conduciendo el vehículo.
PUNTOS BÁSICOS Placa frontal Mando a distancia (RC-406) Sensor remoto (DO lo exponga a la luz solar brillante.) Fijar Rueda de volumen (girar/pulsar) Ranura de carga Desmontar Retire la hoja aislante cuando se utilice por primera vez. * Sin utilizar. Botón de liberación Ventanilla de visualización Cómo reinicializar Cómo cambiar la batería También se borrarán los ajustes preestablecidos por usted.
PROCEDIMIENTOS INICIALES 3 Configuración de los ajustes iniciales 1 2 3 4 1 Cancele la demostración Cuando enciende la unidad (o después de reinicializarla) la pantalla muestra: “CANCEL” \ “DEMO” \ “PRESS” \ “VOLUME” \ “KNOB” 1 Pulse la rueda de volumen. Pulse SRC para ingresar a [STANDBY]. Pulse la rueda de volumen para ingresar en [FUNCTION]. Gire la rueda de volumen para seleccionar [INITIAL] y luego púlsela. Gire la rueda de volumen para seleccionar (consulte la tabla de abajo) y luego púlsela.
RADIO Predeterminado: XX Búsqueda de una emisora 1 Pulse L SRC para seleccionar TUNER. 2 Pulse repetidamente (o pulse *AM– / #FM+ en el RC-406) para seleccionar FM1/ FM2/ FM3/ AM. Aparece “F1” / “F2” / “F3” / “AM” en la pantalla. 3 Pulse 4 / ¢ para buscar una emisora. SEEKMODE Selecciona el método de sintonización para los botones 4 / ¢. AUTO1: Realiza automáticamente la búsqueda de una emisora. ; AUTO2: Busca una emisora presintonizada. ; MANUAL: Buscar manualmente una emisora.
CD / USB Inicie la reproducción CD Lado de la etiqueta 0: Expulsa el disco : Aplicable — : No aplicable La fuente cambia a CD y se inicia la reproducción. USB Terminal de entrada USB CA-U1EX (Máx.: 500 mA) (accesorio opcional) La fuente cambia a USB y se inicia la reproducción. Para Hacer esto Pausar o reanudar la reproducción Seleccionar una pista/ archivo Seleccionar una carpeta Retroceder/avanzar rápidamente Seleccionar una pista/ archivo de una lista Pulse 6 38 (o pulse ENT 38 en el RC-406).
CD / USB Búsqueda directa de música (mediante RC-406) 1 Pulse DIRECT. 2 Pulse los botones numéricos para ingresar un número de pista/archivo. 3 Pulse 4 / ¢ (+) para realizar la búsqueda de música. AUX AJUSTES DE VISUALIZACIÓN Preparativos: Seleccione [AUX ON] para [AUX SET]. (➜ 4) 1 Pulse la rueda de volumen para ingresar en [FUNCTION]. 2 Gire la rueda de volumen para seleccionar [SETTINGS] y luego púlsela. Comience a escuchar 1 Conecte un reproductor de audio portátil (disponible en el mercado).
AJUSTES DE AUDIO MÁS INFORMACIÓN Mientras se escucha desde cualquier fuente... 1 Pulse AUDIO para seleccionar [AUD CTRL]. 2 Gire la rueda de volumen para seleccionar (consulte la tabla de abajo) y luego púlsela. Repita el paso 2 hasta que se seleccione o active el elemento deseado. 3 Para salir, pulse y mantenga pulsado . • Para volver a la jerarquía anterior, pulse .
LOCALIZACIÓN Y SOLUCIÓN DE PROBLEMAS ESPECIFICACIONES SP_KDC-105U[K0].indd 9 Sintonizador Reproductor de CD USB Audio • El sonido no se escucha. • La unidad no se enciende. • La información mostrada en la pantalla no es correcta. El receptor no funciona en absoluto. Reinicialice la unidad. (➜ 3) • Recepción de radio deficiente. • Conecte firmemente la antena. • Ruidos estáticos mientras se escucha • Extraiga completamente la antena. la radio. Aparece “NA FILE”.
INSTALACIÓN / CONEXIÓN Instalación de la unidad (montaje en el tablero) Advertencia • La unidad puede utilizarse solamente con una fuente de alimentación de 12 V CC con negativo a masa. • Desconecte el terminal negativo de la batería antes de realizar el cableado y el montaje. • Para evitar un cortocircuito, no conecte el cable de la batería (amarillo) ni el cable de encendido (rojo) al chasis del vehículo o cable de conexión a masa (negro).
Conexión del cableado REAR/SW R L KDC-MP105U Salida posterior/ subwoofer FRONT REAR/SW KDC-105U R Lista de piezas para la instalación L A Placa frontal Salida delantera Salida posterior/subwoofer ( ×1 ) Fusible (10 A) Terminal de la antena B Manguito de montaje Si no se ha realizado ninguna conexión, no deje que el cable sobresalga de la lengüeta.
CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. In compliance with Federal Regulations, following are reproductions of labels on, or inside the product relating to laser product safety. JVC KENWOOD Corporation 2967-3, ISHIKAWA-MACHI, HACHIOJI-SHI, TOKYO, JAPAN THIS PRODUCT COMPLIES WITH DHHS RULES 21CFR SUBCHAPTER J IN EFFECT AT DATE OF MANUFACTURE.