KMD-D400 3 DISC AND 1 DISC MD AUTO CHANGER INSTRUCTION MANUAL © B64-1426-00 (E) (MC) 00/3 2 1 99/12 11 10 9 8 7 6 5 4 3 2
English Contents Safety precautions Before use 2WARNING Safety Precautions ........................................................................2 To prevent injury or fire, take the following precautions: Operations Buttons and Display ......................................................................5 MD Changer Play ..........................................................................6 Plus-one MD play ..........................................................................
2CAUTION To prevent damage to the machine, take the following precautions: • Make sure to ground the unit to a negative 12V DC power supply. • Do not open the top or bottom covers of the unit. • Do not install the unit in a spot exposed to direct sunlight or excessive heat or humidity. Also avoid places with too much dust or the possibility of water splashing. • Do not set the removed faceplate or the faceplate case in areas exposed to direct sunlight, excessive heat or humidity.
English Safety precautions IMPORTANT INFORMATION This unit is NOT designed to be connected directly to control units that are manufactured and sold before 1994. If used with such units, an optional CA-SD200 (sold separately) must be used. FAILURE TO FOLLOW THESE INSTRUCTIONS MAY RESULT IN DAMAGE TO THIS UNIT AND CONTROL UNIT. Handling Mini discs • Do not leave the MD in the unit for a prolonged period. The ejected MD should be placed in an MD case for storage.
Operations Buttons and Display Release button MENU indicator DEMO indicator KMD-D400 3 MD CHANGER + 1 PLAYER 24BIT RESOLUTION D/A CONVERTER Title display MENU DISP Disc No.
English Operations MD Changer Play To set MDs in the main unit: 1 Insert the first MD in the MD slot. The first MD is set in the play position. 2 Insert the second MD in the MD slot. The second MD is held in the disc No.2 stack position. 3 Insert the third MD in the MD slot. The third MD is held in the disc No.3 stack position. NOTE • The 0 buttons change colour according to the operation state, as follows.
Plus-one MD play Switching Spectrum Analyzer Display Even when three MDs have been set in the main unit, a further MD can be played as the plus-one MD. To play a plus-one MD (a fourth MD): 1 Press one of the 01 - 03 buttons for at least one second. The MD currently set in the play position will now be stored in the stack position. 2 Insert the MD in the MD slot. The disc is then set in the play position. The and the disc begins to play.
English Operations Menu System Table of Adjustment Mode To accommodate a greater number of functions, a function set system has been employed for making settings. Press the DISP button to enter the function set mode and then display the function to make the setting. Adjustment mode (Display) 1 Selecting MD play source mode.
Theft Deterrent Faceplate The faceplate of the unit can be detached and taken with you, helping to deter theft. Removing Faceplate: Press the release button and drop open the faceplate. In its dropped condition, whilst drawing the faceplate to one side, pull it to the front and remove it. Release button 1 3 MD CHANGER + 1 PLAYER KMD-D400 2 3 24BIT RESOLUTION D/A CONVERTER DISP Reattaching Faceplate: Hold the faceplate so that the operation face faces the front toward you and press until it locks.
English Accessories Installation Procedure External view ......... Number of items External view ......... Number of items 1 4 .........2 .........1 2 ........1 3 .........2 2CAUTION The use of any accessories except for those provided might result in damage to the unit. Make sure only to use the accessories shipped with the unit, as shown above. The O-N switch should be set according to the control unit in use as well as to the connected models.
Connections Installation ■ Installation Control input Firewall or metal support White White/Black Centre unit Accessory2 White/Black – + FRONT • L White Gray/Black – Gray Gray/Black Gray KMD-D400 Self-tapping screw (commercially available) + FRONT • R Metal mounting strap (commercially available) Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place.
Installation ■ Removing the Unit English ■ Removing the hard rubber frame 1 Engage the catch pins on the removal tool and remove the two 1 Refer to the section “Removing the hard rubber frame” and locks on the lower level. Lower the frame and pull it forward as shown in the figure. 2 Remove the Hex-head screw with integral washer (M4×8) on then remove the hard rubber frame. the back panel. Catch 3 Insert the two removal tools deeply into the slots on each side, as shown.
Troubleshooting Guide What might seem to be a malfunction in your unit may just be the result of slight misoperation or miswiring. Before calling service, first check the following table for possible problems. PROBLEM POSSIBLE CAUSE SOLUTION The disc control mode cannot be selected. No cable has been connected to the disc changer input terminal on the unit. Connect the control cable to the disc changer input terminal on the centre unit. The disc cannot be changed.
Troubleshooting Guide English The following messages are displayed on the centre unit when certain problems are occurring in your system. Take the recommended actions. NO PANEL E-30 The faceplate of this unit has been removed. ] Replace it. BLANK Nothing has been recorded on the MD. ] The next MD will automatically be played. NO TRACK No tracks are recorded on the MD, although it has a title. ] The next MD will automatically be played. E-99 The unit is malfunctioning for some reason.
Specifications Specifications subject to change without notice. MD player section General Laser diode ....................................................GaAlAs (λ=760 nm) Digital filter (D/A)......................................8 Times Over Sampling D/A Converter......................................................................24 Bit Frequency response (±1 dB) ...................................5 Hz – 20 kHz Total harmonic distortion (1 kHz) .....................................0.
