KDC-X303 KDC-BT375U KDC-BT350U KDC-BT33 KDC-BT275U KDC-BT23 KDC-MP375BT KMR-D375BT CD-RECEIVER INSTRUCTION MANUAL AMPLI-TUNER LECTEUR DE CD MODE D’EMPLOI REPRODUCTOR DE DISCOS COMPACTOS RECEPTOR DE FM/AM MANUAL DE INSTRUCCIONES For your records Record the serial number, found on the back of the unit, in the spaces designated on the warranty card, and in the space provided below. Refer to the model and serial numbers whenever you call upon your Kenwood dealer for information or service on the product.
CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. In compliance with Federal Regulations, following are reproductions of labels on, or inside the product relating to laser product safety. JVC KENWOOD Corporation 2967-3, ISHIKAWA-MACHI, HACHIOJI-SHI, TOKYO, JAPAN THIS PRODUCT COMPLIES WITH DHHS RULES 21CFR SUBCHAPTER J IN EFFECT AT DATE OF MANUFACTURE.
IC (Industry Canada) Notice This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device.
SOFTWARE LICENSE AGREEMENT The software embedded in the Product (hereinafter the "Licensed Software") provided by Licensor is copyrighted to or sublicensable by the Licensor, and this Agreement provides for the terms and conditions which Users shall follow in order to use the Licensed Software. The User shall use the Licensed Software by agreeing with the terms of this Software License Agreement.
Article 10 1. 2. The copyright and all the other intellectual property rights relating to the Licensed Software shall belong to the Licensor and the Original Rightholder, and in no event shall they be under the ownership of the User. The User shall, whenever it uses the Licensed Software, comply with any laws relating to the copyright and other intellectual property rights. Article 11 1. 2. 3. 2. 3.
CONTENTS BEFORE USE BEFORE USE 2 IMPORTANT BASICS 3 GETTING STARTED 4 • To ensure proper use, please read through this manual before using this product. It is especially important that you read and observe Warnings and Cautions in this manual. • Please keep the manual in a safe and accessible place for future reference.
BASICS Faceplate Remote control (RC-406) (supplied for ) Display window Volume knob Remote sensor (Do not expose to bright sunlight.) Loading slot Lights up when Bluetooth connection is established.*1 (Page 17) Detach button Attach Detach Pull out the insulation sheet when using for the first time. / / : Can be remotely controlled with an optionally purchased remote control. / / / : Remote control functions are not available.
GETTING STARTED To set the date 7 Turn the volume knob to select [DATE FORMAT], then press the knob. 8 Turn the volume knob to select [DD/MM/YY] or [MM/DD/YY], then press the knob. 9 Turn the volume knob to select [DATE SET], then press the knob. 10 Turn the volume knob to make the settings, then press the knob.
GETTING STARTED [DISPLAY] [EASY MENU] [USER S.REMO] (For / / / ) When entering [FUNCTION]... [ON]: [ZONE 1] illumination changes to white color. ; [OFF]: [ZONE 1] illumination remains as [COLOR SELECT] color. (Page 29) • [ZONE 2] illumination changes to light blue color when you enter [FUNCTION], irregardless of the [EASY MENU] setting. • Refer to the illustration on page 28 for zone identification.
RADIO GETTING STARTED Preparation: Press B SRC repeatedly to enter STANDBY, then press the volume knob to enter [FUNCTION]. 1 Turn the volume knob to select an item, then press the knob. [SYSTEM] [REM SETTING] [REMOTE ID SET] Remote control ID list is displayed. • [YES] indicates that this ID is already registered. • [NO] indicates that this ID is available. 2 Turn the volume knob to select an available ID [REM ID1]/[REM ID2]/ [REM ID3], then press the knob. “REGISTERING” appears on the display window.
RADIO Other settings 1 Press the volume knob to enter [FUNCTION]. 2 Turn the volume knob to select an item (see the following table), then [TI] [ON]: Allows the unit to temporarily switch to Traffic Information if available (“TI” lights up). ; [OFF]: Cancels. [PTY SEARCH] (For press the knob. 3 Repeat step 2 until the desired item is selected/activated or follow the instructions stated on the selected item. 4 Press and hold to exit.
CD/USB/iPod/ANDROID Start playback The source changes automatically and playback starts. CD Label side Eject disc USB input terminal USB To On the faceplate On the remote control Play back/pause Press 6 IW. Press ENT IW. Reverse/Fast-forward*4 Press and hold S / T. Press and hold S / T (+). Select a track/file Press S / T. Press S / T (+). Select a folder*5 Press 2 /1 Press #FM+/ AM–. Repeat play*4*6 Press 4 repeatedly. CA-U1EX (max.
CD/USB/iPod/ANDROID Select music drive Select a file from a folder/list While in USB source, press 5 repeatedly. For iPod, applicable only when [MODE OFF] is selected. Stored songs in the following drive will be played back. • Selected internal or external memory of a smartphone (Mass Storage Class). • Selected drive of a multiple drive device. 1 Press . 2 Turn the volume knob to select a folder/list, then press the knob. 3 Turn the volume knob to select a file, then press the knob.
AUX CD/USB/iPod/ANDROID Preparation: • Select [ON] for [BUILT-IN AUX] in [SOURCE SELECT]. (Page 5) Direct Music Search (using the remote control) 1 Press DIRECT. 2 Press the number buttons to enter a track/file number. 3 Press ENT IW to search for music. Start listening 1 Connect a portable audio player (commercially available). • To cancel, press or DIRECT. • Not available if Random Play is selected. • Not applicable for iPod USB and ANDROID source.
Pandora® Preparation: Install the latest version of the Pandora application on your device (iPhone/iPod touch), then create an account and log in to Pandora. • Select [ON] for [PANDORA SRC] in [SOURCE SELECT]. (Page 5) Create and store a new station . 1 Press 2 Turn the volume knob to select [NEW STATION], then press the knob. 3 Turn the volume knob to select [FROM ARTIST] or [FROM TRACK], then press the knob. A new station is created based on the current artist or current song.
iHeartRadio® Preparation: Install the latest version of iHeartAuto application on your device (iPhone/ iPod touch), then create an account and log in to iHeartRadio. • Select [ON] for [IHEART SRC] in [SOURCE SELECT]. (Page 5) Start listening 1 Start up the iHeartAuto application on your device. 2 Connect your device to the USB input terminal. USB input terminal To On the faceplate On the remote control Play back/pause Press 6 IW. Press ENT IW. Skip a track for custom Press T. station Press T (+).
Spotify Preparation: Install the latest version of the Spotify application on your device (iPhone/ iPod touch), then create an account and log in to Spotify. • Select [ON] for [SPOTIFY SRC] in [SOURCE SELECT]. (Page 5) To On the faceplate Random play*5 Press 3 repeatedly *3. [SHUFFLE ON], [SHUFFLE OFF] On the remote control ( Not available ) *1 *2 *3 *4 KCA-iP102: 30-pin type, KCA-iP103: Lightning type Do not leave the cable inside the car when not used. Available for premium account users only.
SiriusXM® Radio (for / / / Only SiriusXM® brings you more of what you love to listen to, all in one place. Get over 140 channels, including commercial-free music plus the best sports, news, talk, comedy and entertainment. Welcome to the world of satellite radio. A SiriusXM Vehicle Tuner and Subscription are required. For more information, visit . Preparation: 1 Connect the optional SiriusXM Vehicle Tuner (commercially available).
SiriusXM® Radio (for / / / SiriusXM Keymode ) SmartFavorites and TuneStart™ Press and hold the volume knob to change the keymode (channel or replay). (Default: Channel keymode) “ ” lights up when replay keymode is selected. When channel keymode is selected... To On the faceplate On the remote control Select a channel Press S / T. Press S / T (+). Change a channel rapidly Press and hold S / T. Press and hold S / T (+).
SiriusXM® Radio (for / / / ) SiriusXM settings [LOCK SETTING] [MATURE CH]: Selects the SiriusXM-defined lock setting. ; [USER DEFINED]: Selects the individual channels the user wants to lock. ; [OFF]: Cancels. press the knob. 3 Repeat step 2 until the desired item is selected/activated or follow the instructions stated on the selected item. 4 Press and hold to exit. [CHANNEL EDIT]*1 1 Turn the volume knob to select a category, then press the knob.
BLUETOOTH® BLUETOOTH — Connection Supported Bluetooth profiles – Hands-Free Profile (HFP) – Advanced Audio Distribution Profile (A2DP) – Audio/Video Remote Control Profile (AVRCP) – Serial Port Profile (SPP) – Phonebook Access Profile (PBAP) Supported Bluetooth codecs – Sub Band Codec (SBC) – Advanced Audio Coding (AAC) Connect the microphone Depending on the operating system and the firmware version of your mobile phone, Bluetooth features may not work with this unit.
BLUETOOTH® Auto Pairing When you connect iPhone/iPod touch to the USB input terminal, pairing request (via Bluetooth) is automatically activated. Press the volume knob to pair once you have confirmed the device name. The following operations may differ or be unavailable depending on the connected phone. To On the faceplate On the remote control Answer a call Press or the volume knob or one of the number buttons (1 to 6). Press . Reject a call Press . Press . End a call Press . Press .
BLUETOOTH® *1 This adjustment will not affect the volume of the other sources. *2 Press and hold VOL to continuously increase the volume to 15. *3 Operations may vary according to the connected Bluetooth device. Make a call You can make a call from the call history, phonebook, or dialing the number. Call by voice is also possible if your mobile phone has the feature. Improve the voice quality 1 Press While talking on the phone... 1 Press the volume knob to enter [FUNCTION].
BLUETOOTH® [PHONE BOOK] (Applicable only if the phone supports PBAP.) 1 Turn the volume knob quickly to enter alphabet search mode (if the phonebook contains many contacts). The first menu (ABCDEFGHIJK) appears. • To go to the other menu (LMNOPQRSTUV or WXYZ1 ), press 2 / 1 . • To select the desired first letter, turn the volume knob or press S / T, then press the knob. Select “1” to search with numbers and select “ ” to search with symbols. 2 Turn the volume knob to select a name, then press the knob.
BLUETOOTH® Other settings [INITIALIZE] 1 Press the volume knob to enter [FUNCTION]. 2 Turn the volume knob to select an item (see the following table), then press the knob. 3 Repeat step 2 until the desired item is selected/activated or follow the instructions stated on the selected item. 4 Press and hold to exit. To return to the previous setting item, press . [YES]: Initializes all the Bluetooth settings (including stored pairing, phonebook, and etc.). ; [NO]: Cancels.
BLUETOOTH® BLUETOOTH — Audio To On the faceplate Repeat play Press 4 On the remote control repeatedly. [ALL REPEAT], [FILE REPEAT], [REPEAT OFF] Random play While in BT AUDIO source, you can connect to five Bluetooth audio devices and switch between these five devices. Audio player via Bluetooth 1 Press B SRC repeatedly (or press SRC on the remote control) to select BT AUDIO. • Pressing enters BT AUDIO directly. 2 Operate the audio player via Bluetooth to start playback.
BLUETOOTH® Settings to use KENWOOD Remote application KENWOOD Remote application is designed to control the KENWOOD car receiver’s operations from the iPhone/iPod (via Bluetooth or via USB input terminal) or Android smartphone (via Bluetooth). • For / / / , “R.APP” indicator on the display window lights up when KENWOOD Remote application is connected. [ANDROID LIST]* Selects the Android smartphone to use from the list. [STATUS] Shows the status of the selected device.
BLUETOOTH® Internet radio via Bluetooth You can listen to internet radio (Pandora, iHeartRadio and Spotify) on the iPhone/iPod touch/Android device via Bluetooth on this unit. • Make sure the USB input terminal is not connected to any device. Listen to Pandora Preparation: Select [ON] for [PANDORA SRC] in [SOURCE SELECT]. (Page 5) 1 Start up the Pandora application on your device. 2 Connect your device via Bluetooth connection.
AUDIO SETTINGS [MANUAL EQ] [62.5HZ] 1 Press the volume knob to enter [FUNCTION]. 2 Turn the volume knob to select an item (see the following table), then press the knob. 3 Repeat step 2 until the desired item is selected or activated. 4 Press and hold to exit. (or using the remote control) 1 Press AUD to enter [AUDIO CONTROL]. 2 Press J/K a to select an item, then press ENT IW. To return to the previous setting item, press .
AUDIO SETTINGS [X ‘ OVER] [SOUND EFFECT] [SOUND RECNSTR] (Sound reconstruction) [SPACE ENHANCE] (Not applicable for RADIO source, AUX source and SIRIUS XM source.) [ON]: Creates realistic sound by compensating the high-frequency components and restoring the rise-time of the waveform that are lost in audio data compression. ; [OFF]: Cancels. (Not applicable for RADIO source.) [SML]/[MED]/[LRG]: Virtually enhances the sound space. ; [OFF]: Cancels.
AUDIO SETTINGS [SW LPF SLOPE] [–6DB]/[–12DB]/[–18DB]/[–24DB]: Adjusts the crossover slope. (Selectable only if a setting other than [THROUGH] is selected for [SW LPF FRQ].) [SW LPF PHASE] [SW LPF GAIN] [DTA SETTINGS] [REVERSE] (180°)/[NORMAL] (0°): Selects the phase of the subwoofer output to be in line with the speaker output for optimum performance. [–8] to [0]: Adjusts the output volume of the subwoofer.
AUDIO SETTINGS DISPLAY SETTINGS • Before making an adjustment for [DISTANCE] and [GAIN] of [DTA SETTINGS], select the speaker you want to adjust: [FRONT LEFT]/[FRONT RIGHT]/[REAR LEFT]/[REAR RIGHT]/[SUBWOOFER] – You can only select [REAR LEFT], [REAR RIGHT] and [SUBWOOFER] if a setting other than [NONE] is selected for [REAR] and [SUBWOOFER] of [SPEAKER SIZE]. • [R-SP LOCATION] of [CAR SETTING] is selectable only if a setting other than [NONE] is selected for [REAR] of [SPEAKER SIZE].
DISPLAY SETTINGS Other settings [DIMMER] Dims the illumination. [ON]: Dimmer is turned on. [OFF]: Dimmer is turned off. [DIMMER TIME]: Set the dimmer on and off time. 1 Turn the volume knob to adjust the [ON] time, then press the knob. 2 Turn the volume knob to adjust the [OFF] time, then press the knob. Default: [ON]: [6:00PM] ; [OFF]: [6:00AM] [BRIGHTNESS] 1 Select a zone. (See the illustration on page 28.) 2 [LVL 00] to [LVL 31]: Set the brightness level for the selected zone.
LEARNING STEERING REMOTE CONTROL (for You can control the unit with the steering remote control keys on your vehicle. After connection, you can configure the control keys according to your preference. • You can only make this configuration if your vehicle is equipped with the electrical steering remote control. • If the steering remote control in your car is not compatible, configuration may not be completed and an error message may appear.
REFERENCES Maintenance Cleaning the unit Wipe off dirt on the faceplate with a dry silicone or soft cloth. Cleaning the connector Detach the faceplate and clean the connector gently with a cotton swab. Be careful not to damage the connector. Connector (on the reverse side of the faceplate) Handling discs • Do not touch the recording surface of the disc. • Do not stick tape etc. on the disc, or use a disc with tape stuck on it. • Do not use any accessories for the disc.
REFERENCES • The song order displayed on the selection menu of this unit may differ from that of the iPod/ iPhone. • You cannot operate iPod if “KENWOOD” or “ ” is displayed on iPod. • Depending on the version of the operating system of the iPod/iPhone, some functions may not operate on this unit. • Spotify is a third party service, therefore the specifications are subject to change without prior notice. Accordingly, compatibility may be impaired or some or all of the services may become unavailable.
REFERENCES Change the display information (for / / / ) Each time you press DISP, the display information changes. • If the information is unavailable or not recorded, “NO TEXT”, “NO INFO”, or other information (eg. station name) appears or display will be blank.
REFERENCES Change the display information (for / / / ) Each time you press DISP, the display information changes. • If the information is unavailable or not recorded, “NO TEXT”, “NO INFO”, or other information (eg. station name) appears or display will be blank.
TROUBLESHOOTING Symptom Remedy • Adjust the volume to the optimum level. • Check the cords and connections. “MISWIRING CHECK WIRING THEN PWR ON” appears. Turn the power off, then check to be sure the terminals of the speaker wires are insulated properly. Turn the power on again. “PROTECTING SEND SERVICE” appears. Send the unit to the nearest service center. Source cannot be selected. Check the [SOURCE SELECT] setting. (Page 5) • Sound cannot be heard. • The unit does not turn on.
TROUBLESHOOTING Symptom This unit is still preparing the iPod/iPhone music list. It may take some time to load, try again later. “NO DISC” Insert a playable disc into the loading slot. “ADD ERROR” New station creation is unsuccessful. “TOC ERROR” Make sure the disc is clean and inserted properly. “CHECK DEVICE” Check the Pandora application on your device. “NA FILE” Make sure the media (disc/USB) contain supported audio files. (Page 31) “NO SKIPS” The skip limit has been reached.
TROUBLESHOOTING SiriusXM® Radio Spotify “CONNECTING” USB is disconnected from the head unit. Please make sure the device is connected properly through USB. • Connected via USB input terminal: The device is connecting to the head unit. Please wait. • Connected via Bluetooth: The Bluetooth is disconnected. Please check Bluetooth connection and make sure both the device and unit are paired and connected. “CHECK APP” The Spotify application is not connected properly or user is not login.
INSTALLATION/CONNECTION TROUBLESHOOTING Symptom Bluetooth® The connected Bluetooth audio player cannot be controlled. 38 Remedy • Check whether the connected Bluetooth audio player supports Audio/Video Remote Control Profile (AVRCP). (Refer to the instructions of your audio player.) • Disconnect and connect the Bluetooth player again. “NOT SUPPORT” The connected phone does not support Voice Recognition feature or phonebook transfer.
INSTALLATION/CONNECTION Part list for installation (A) Faceplate (×1) Installing the unit (in-dash mounting) (B) Trim plate (×1) Do the required wiring. (Page 40) (C) Mounting sleeve (×1) (D) Wiring harness (×1) Hook on the top side Orientate the trim plate as illustrated before fitting. (E) Extraction key (×2) Dashboard of your car (F) Screws* M5 × 7 mm (×4) Bend the appropriate tabs to hold the sleeve firmly in place. M5 × 6 mm (×4) M4 × 8 mm (×1) * Supplied for / / .
INSTALLATION/CONNECTION Wiring connection IMPORTANT We recommend installing the unit with a commercially available custom wiring harness specific for your car and leave this job to professionals for your safety. Consult your car audio dealer. Fuse (10 A) Antenna terminal White To front speaker (left) Gray To front speaker (right) Gray/Black Green To rear speaker (left) To rear speaker (right) Ignition switch If no connections are made, do not let the wire come out from the tab.
INSTALLATION/CONNECTION Connecting external components : To KENWOOD Marine Remote Control unit, KCA-RC55MR (optional accessory) (page 5) : Learning steering remote control (page 30) Microphone input jack (page 17) / Expansion port (12 V / / : 500 mA): To the optional SiriusXM Vehicle Tuner (commercially available) (page 14) Output terminals When connecting to an external amplifier, connect its ground wire to the car’s chassis to avoid damaging the unit. ENGLISH JS_KWD_KDC_X303_KN_EN_6th.
FM Frequency Range / / / / / / : 87.9 MHz — 107.9 MHz (200 kHz step) CD player SPECIFICATIONS Quieting Sensitivity (S/N = 46 dB, Dev 40 kHz) 17.2 dBf (2.0 μV/75 Ω) Frequency Response (±3 dB) 30 Hz — 15 kHz Signal-to-Noise Ratio (MONO) 64 dB Stereo Separation (1 kHz) 40 dB AM Frequency Range CD player Usable Sensitivity (S/N = 20 dB) 42 530 kHz — 1 700 kHz (10 kHz step) 29 dBμ (28.2 μV) USB 8.2 dBf (0.71 μV/75 Ω) Auxiliary Usable Sensitivity (S/N = 30 dB, Dev 22.
SPECIFICATIONS Operating Voltage 12 V DC car battery Full Bandwidth Power (at less than 1 % THD) 22 W × 4 Installation Size (W × H × D) 182 mm × 53 mm × 155.5 mm (7-3/16" × 2-1/16" × 6-1/8") Speaker Impedance 4Ω—8Ω 1.2 kg (2.7 lbs) Tone Action Band 1: 62.5 Hz ±9 dB Band 2: 100 Hz ±9 dB Band 3: 160 Hz ±9 dB Band 4: 250 Hz ±9 dB Band 5: 400 Hz ±9 dB Band 6: 630 Hz ±9 dB Band 7: 1 kHz ±9 dB Band 8: 1.6 kHz ±9 dB Band 9: 2.5 kHz ±9 dB Band 10: 4 kHz ±9 dB Band 11: 6.
libFLAC Copyright (C) 2000-2009 Josh Coalson Copyright (C) 2011-2013 Xiph.Org Foundation Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: - Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
ENGLISH FRANÇAIS ESPAÑOL KDC-X303 KDC-BT375U KDC-BT350U KDC-BT33 KDC-BT275U KDC-BT23 CD-RECEIVER Quick Start Guide AMPLI-TUNER LECTEUR DE CD Guide de démarrage rapide REPRODUCTOR DE DISCOS COMPACTOS RECEPTOR DE FM/AM Guía de inicio rápido KDC-MP375BT KMR-D375BT For detailed operations and information, refer to the INSTRUCTION MANUAL on the following website: Pour les opérations et les informations détaillées, reportez-vous au MODE D’EMPLOI sur le site web suivant: Para obtener más información y detal
CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. In compliance with Federal Regulations, following are reproductions of labels on, or inside the product relating to laser product safety. JVC KENWOOD Corporation 2967-3, ISHIKAWA-MACHI, HACHIOJI-SHI, TOKYO, JAPAN THIS PRODUCT COMPLIES WITH DHHS RULES 21CFR SUBCHAPTER J IN EFFECT AT DATE OF MANUFACTURE.
IC (Industry Canada) Notice This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device.
SOFTWARE LICENSE AGREEMENT The software embedded in the Product (hereinafter the "Licensed Software") provided by Licensor is copyrighted to or sublicensable by the Licensor, and this Agreement provides for the terms and conditions which Users shall follow in order to use the Licensed Software. The User shall use the Licensed Software by agreeing with the terms of this Software License Agreement.
Article 10 1. 2. The copyright and all the other intellectual property rights relating to the Licensed Software shall belong to the Licensor and the Original Rightholder, and in no event shall they be under the ownership of the User. The User shall, whenever it uses the Licensed Software, comply with any laws relating to the copyright and other intellectual property rights. Article 11 1. 2. 3. 2. 3.
INSTALLATION/CONNECTION Basic procedure 1 Remove the key from the ignition switch, then disconnect the Warning • The unit can only be used with a 12 V DC power supply, negative ground. • Disconnect the battery’s negative terminal before wiring and mounting. • Do not connect Battery wire (yellow) and Ignition wire (red) to the car chassis or Ground wire (black) to prevent a short circuit. • To prevent short circuit: – Insulate unconnected wires with vinyl tape.
Wiring connection Installing the unit (without mounting sleeve) 1 Remove the mounting sleeve and trim plate from the unit. 2 Align the holes in the unit (on both sides) with the vehicle mounting bracket and secure the unit with screws (supplied/ commercially available). Antenna terminal Fuse (10 A) Use only the specified screws. Using wrong screws might damage the unit. If no connections are made, do not let the wire come out from the tab.
BEFORE USE BASICS IMPORTANT Faceplate • To ensure proper use, please read through this Guide before using this product. It is especially important that you read and observe Warnings and Cautions in this Guide. • Please keep the Guide in a safe and accessible place for future reference. Display window Volume knob Loading slot Warning USB input terminal Do not operate any function that takes your attention away from safe driving.
GETTING STARTED 1 Select the display language and cancel the demonstration When you turn on the power for the first time (or [FACTORY RESET] is set to [YES]), the display shows: “SEL LANGUAGE” “PRESS” “VOLUME KNOB” 1 Turn the volume knob to select [ENG] (English) or [SPA] (Spanish), then press the knob. [ENG] is selected for the initial setup. ) the display shows: “CANCEL DEMO” Then, (except for “PRESS” “VOLUME KNOB”. 2 Press the volume knob again. [YES] is selected for the initial setup.
RADIO CD/USB/iPod/ANDROID Search for a station 1 Press B SRC repeatedly to select RADIO. 2 Press BAND repeatedly to select FM1/FM2/FM3/AM. 3 Press S / T to search for a station. Start playback The source changes automatically and playback starts when you load a disc or attach a device (USB device/ iPod/iPhone/ Android device) to the USB input terminal. To On the faceplate You can store up to 18 stations for FM and 6 stations for AM. Play back/pause Press 6 IW.
Examples of some well-used settings FUNCTIONS SETTINGS Subwoofer Level Setting 1 2 3 4 Press the volume knob to enter [FUNCTION]. Turn the volume knob to select an item, then press the knob. Repeat step 2 until the desired item is selected or activated. Press and hold to exit. To return to the previous setting item, press . • Refer to the INSTRUCTION MANUAL on the following website for the detailed explanation of each item:
Illumination Color Setting For / / / preferred illumination color for each zone. , you can set your 6 Repeat step 4 and step 5 to set color for other zones. 7 Press and hold to exit. OTHER INFORMATION 1 Press the volume knob to enter [FUNCTION]. For playback operations of AUX, SPOTIFY, Pandora®, iHeartRadio®, SiriusXM® Radio sources, refer to the INSTRUCTION MANUAL on the following website: • The availability of each source vary depending on the model.
BLUETOOTH® Depending on the operating system and the firmware version of your mobile phone, Bluetooth features may not work with this unit. Once pairing is completed, Bluetooth connection is established automatically. / / / : “BT1” and/or “BT2” • indicator on the faceplate lights up. • / / / : “BT1” and/or “BT2” on the display window lights up. Connect the microphone Connect the supplied microphone to the microphone input jack on the rear panel.
• Microsoft and Windows Media are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. • Use of the Made for Apple badge means that an accessory has been designed to connect specifically to the Apple product(s) identified in the badge, and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards.
