KDC-X704 KDC-X304 KDC-BT778HD KDC-BT378U KDC-BT360U KDC-BT34 KDC-BT278U KDC-MP378BT KMR-D378BT CD-RECEIVER INSTRUCTION MANUAL AUTORADIO CD MODE D’EMPLOI RECEPTOR CD MANUAL DE INSTRUCCIONES For your records Record the serial number, found on the back of the unit, in the spaces designated on the warranty card, and in the space provided below. Refer to the model and serial numbers whenever you call upon your Kenwood dealer for information or service on the product.
CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. In compliance with Federal Regulations, following are reproductions of labels on, or inside the product relating to laser product safety. JVC KENWOOD Corporation 2967-3, ISHIKAWA-MACHI, HACHIOJI-SHI, TOKYO, JAPAN THIS PRODUCT COMPLIES WITH DHHS RULES 21CFR SUBCHAPTER J IN EFFECT AT DATE OF MANUFACTURE.
IC (Industry Canada) Caution This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference, including interference that may cause undesired operation of the device.
SOFTWARE LICENSE AGREEMENT The software embedded in the Product (hereinafter the "Licensed Software") provided by Licensor is copyrighted to or sublicensable by the Licensor, and this Agreement provides for the terms and conditions which Users shall follow in order to use the Licensed Software. The User shall use the Licensed Software by agreeing with the terms of this Software License Agreement.
Article 9 Destruction of the Licensed Software If this Agreement is terminated pursuant to the provision of Article 8, the User shall destroy the Licensed Software, any related documents and copies thereof within two (2) weeks from such date of termination. Article 10 1. 2. Article 11 1. 2. 3. 2. 3.
Important Notice concerning the Software -CMP -jansson The MIT License (MIT) Copyright (c) 2014 Charles Gunyon Copyright (c) 2009-2012 Petri Lehtinen
vi JS_KWD_KDC_X704_KN_C.
Contents Before Use ................................................................................................. 3 Audio Settings........................................................................................ 29 Basics ......................................................................................................... 4 Display Settings ..................................................................................... 33 Getting Started .............................................
Before Use IMPORTANT • To ensure proper use, please read through this manual before using this product. It is especially important that you read and observe Warnings and Cautions in this manual. • Please keep the manual in a safe and accessible place for future reference. WARNING • Do not operate any function that takes your attention away from safe driving. • Do not ingest the battery, Chemical Burn Hazard. The remote control supplied with this product contains a coin/button cell battery.
Basics Faceplate Attach Volume knob Loading slot Lights up when Bluetooth connection is established. (Page 22) Detach How to reset Reset the unit within 5 seconds after detaching the faceplate. Detach button Display window*1 To On the faceplate Turn on the power Press B SRC. • Press and hold to turn off the power.*2 Adjust the volume Turn the volume knob. Select a source • Press B SRC repeatedly. • Press B SRC, then turn the volume knob within 2 seconds.
Getting Started Basics Remote control (RC-406) (supplied for ) Remote sensor (Do not expose to bright sunlight.) Pull out the insulation sheet when using for the first time. / / / / : Can be remotely controlled with an optionally purchased remote control. / / : Remote control functions are not available. How to replace the battery To On the remote control Adjust the volume Press VOL or VOL . • Press and hold VOL to continuously increase the volume to 15.
Getting Started To set the date 7 Turn the volume knob to select [DATE FORMAT], then press the knob. 8 Turn the volume knob to select [DD/MM/YY] or [MM/DD/YY], then press the knob. 9 Turn the volume knob to select [DATE SET], then press the knob. 10 Turn the volume knob to make the settings, then press the knob. Set the date in the order of “Day” “Month” “Year” or “Month” “Day” “Year”. 11 Press and hold [DISPLAY] [EASY MENU] (For / / / / / ) When entering [FUNCTION]...
Getting Started [CD READ] [1]: Automatically distinguishes between audio file disc and music CD. ; [2]: Forces to play as a music CD. No sound can be heard if an audio file disc is played. [USER S.REMO] (For ) See page 35 for details. [F/W UPDATE] [UPDATE SYSTEM]/[UPDATE HD] (for [F/W UP xxxx] [FACTORY RESET] [ENGLISH] [ESPANOL] [FRANCAIS] / ) [YES]: Starts upgrading the firmware. ; [NO]: Cancels (upgrading is not activated). For details on how to update the firmware, visit .
HD Radio™ Tuner (for / ) You can tune in to both conventional and HD Radio broadcasts. • To find HD Radio stations in your area, visit . Select an HD Radio multicast channel Many HD Radio stations offer more than one channel programming. This service is called multicasting. While receiving HD Radio multicast channels.... Press S / T to select your desired channel (HD1 to HD8). “LINKING” appears while linking to a multicast channel.
HD Radio™ Tuner (for / ) Default: [XX] Display received emergency alert messages The received emergency alert messages are stored in the Alert Message List, and you can check them later. While listening to the HD RADIO source... 1 Press to display the Alert Message List. 2 Turn the volume knob to select a message. 3 Press the volume knob to display the information related to the message. 4 Press [TUNER SETTING] [SEEK MODE] Selects the searching method for S / T buttons when pressed.
Radio (for / / / / / / ) Other settings 1 Press the volume knob to enter [FUNCTION]. 2 Turn the volume knob to select an item (see the following table), then press the knob. 3 Repeat step 2 until the desired item is selected/activated or follow the • “ST” indicator lights up when receiving an FM stereo broadcast with sufficient signal strength. • The unit switches to FM alarm automatically when receiving an alarm signal from FM broadcast.
(for / / Radio / / / / ) [TI] [ON]: Allows the unit to temporarily switch to Traffic Information if available (“TI” indicator lights up). ; [OFF]: Cancels. [PTY SEARCH] (For CD/USB/iPod Insert a disc Eject disc ) (For 1 Turn the volume knob to select the available Program Type (for Radio Data System, see page 41), then press the knob. 2 Turn the volume knob to select the PTY language ([ENGLISH]/ [FRENCH]/[GERMAN]), then press the knob. 3 Press S / T to start searching.
CD/USB/iPod Select music drive While in USB source, press 5 repeatedly. Stored songs in the following drive will be played back. • Selected internal or external memory of a smartphone (Mass Storage Class). • Selected drive of a multiple drive device. To On the faceplate On the remote control You can also select the music drive from the [FUNCTION] menu. Play back/pause Press 6 IW. Press ENT IW. Reverse/Fast-forward Press and hold S / T. Press and hold S / T (+). Select a track/file Press S / T.
CD/USB/iPod • To cancel, press or DIRECT. • Not available if Random Play is selected. • Not applicable for iPod USB source. Select a file to play From a folder or list • For iPod, applicable only when [MODE OFF] is selected. (Page 12) 1 Press . 2 Turn the volume knob to select a folder/list, then press the knob. 3 Turn the volume knob to select a file, then press the knob. Alphabet search (applicable only for iPod USB source and iPod BT source) Selected file starts playing.
Pandora® (for / / / / You can listen to Pandora on iPhone/iPod touch (via Bluetooth or via USB input terminal) or Android device (via Bluetooth). Preparation: • Install the latest version of the Pandora application on your device (iPhone/ iPod touch or Android device), then create an account and log in to Pandora. • Select [ON] for [PANDORA SRC] in [SOURCE SELECT]. (Page 6) / / ) To On the faceplate On the remote control Play back/pause Press 6 IW. Press ENT IW. Skip a track Press T.
(for Pandora® / / / / / / / ) Bookmark current song information Press and hold the volume knob. “BOOKMARKED” appears and the information is stored to your device. • The bookmark is available on your Pandora account but not on this unit. Delete a station Spotify You can listen to Spotify on iPhone/iPod touch (via Bluetooth or via USB input terminal) or Android device (via Bluetooth).
Spotify To On the faceplate On the remote control Play back/pause Press 6 IW. Press ENT IW. Skip a track Press S*3 / T. Press S*3 / T (+). Select thumbs up or thumbs down *4 Press 2 /1 . Press #FM+/ AM–. Start radio Press and hold 5. ( Not available ) Repeat play*5 Press 4 ( Not available ) repeatedly. [REPEAT ALL], [REPEAT ONE]*3, [REPEAT OFF] Random play*5 Press 3 repeatedly *3. ( Not available ) Search for a song or station .
SiriusXM® Radio (for / / / / / ) Only SiriusXM® brings you more of what you love to listen to, all in one place. Get over 140 channels, including commercial-free music plus the best sports, news, talk, comedy and entertainment. Welcome to the world of satellite radio. A SiriusXM Vehicle Tuner and Subscription are required. For more information, visit . 1 Press B SRC repeatedly to select SIRIUS XM. 2 Press BAND repeatedly to select a band. 3 Press .
SiriusXM® Radio (for / / / SiriusXM Keymode / / ) SmartFavorites and TuneStart™ Press and hold the volume knob to change the keymode (channel or replay). (Default: Channel keymode) “ ” indicator lights up when replay keymode is selected. When channel keymode is selected... To On the faceplate On the remote control Select a channel Press S / T. Press S / T (+). Change a channel rapidly Press and hold S / T. Press and hold S / T (+).
SiriusXM® Radio (for / / / SiriusXM settings 1 Press the volume knob to enter [FUNCTION]. 2 Turn the volume knob to select an item (see the following table), then press the knob. / / [LOCK SETTING] [MATURE CH]: Selects the SiriusXM-defined lock setting. ; [USER DEFINED]: Selects the individual channels the user wants to lock. ; [OFF]: Cancels. [CHANNEL EDIT]*1 1 Turn the volume knob to select a category, then press the knob.
AUX Using Other Applications You can listen to music from a portable audio player via the auxiliary input jack. KENWOOD Remote application Preparation: Select [ON] for [BUILT-IN AUX] in [SOURCE SELECT]. (Page 6) Start listening 1 Connect a portable audio player (commercially available). You can control the KENWOOD car receiver from iPhone/iPod touch (via Bluetooth or via USB input terminal) or Android device (via Bluetooth) using KENWOOD Remote application. • For more information, visit
Using Other Applications Settings to use KENWOOD Remote application [STATUS] 1 Press the volume knob to enter [FUNCTION]. 2 Turn the volume knob to select an item (see the following table), then press the knob. 3 Repeat step 2 until the desired item is selected/activated. 4 Press and hold to exit. To return to the previous setting item, press . Shows the status of the selected device.
Bluetooth® • Depending on the Bluetooth version, operating system and the firmware version of your mobile phone, Bluetooth features may not work with this unit. • Be sure to turn on the Bluetooth function of the device to make the following operations. • Signal conditions vary depending on the surroundings.
Bluetooth® • Refer to the instruction manual of the Bluetooth device for more information. Auto Pairing When you connect iPhone/iPod touch to the USB input terminal, pairing request (via Bluetooth) is automatically activated if [AUTO PAIRING] is set to [ON]. (Page 26) The following operations may differ or be unavailable depending on the connected phone. To On the faceplate On the remote control Answer a call Press or the volume knob or one of the number buttons (1 to 6). Press .
Bluetooth® *1 This adjustment will not affect the volume of the other sources. *2 Press and hold VOL to continuously increase the volume to 15. *3 Operations may vary according to the connected Bluetooth device. Make a call You can make a call from the call history, phonebook, or dialing the number. Call by voice is also possible if your mobile phone has the feature. Improve the voice quality 1 Press While talking on the phone... 1 Press the volume knob to enter [FUNCTION].
Bluetooth® [PHONE BOOK] (Applicable only if the phone supports PBAP.) 1 Turn the volume knob quickly to enter alphabet search mode (if the phonebook contains many contacts). The first menu (ABCDEFGHIJK) appears. • To go to the other menu (LMNOPQRSTUV or WXYZ1 ), press 2 / 1 . • To select the desired first letter, turn the volume knob or press S / T, then press the knob. Select “1” to search with numbers and select “ ” to search with symbols. 2 Turn the volume knob to select a name, then press the knob.
Bluetooth® Bluetooth mode settings [INITIALIZE] 1 Press the volume knob to enter [FUNCTION]. 2 Turn the volume knob to select an item (see the following table), then press the knob. 3 Repeat step 2 until the desired item is selected/activated or follow the Bluetooth test mode You can check the connectivity of the supported profile between the Bluetooth device and the unit. • Make sure there is no Bluetooth device paired. instructions stated on the selected item. to exit.
Bluetooth® Bluetooth — Audio To On the faceplate Repeat play Press 4 repeatedly. [ALL REPEAT], [FILE REPEAT], [GROUP REPEAT]*, [REPEAT OFF] While in BT AUDIO source, you can connect to five Bluetooth audio devices and switch between these five devices. Listen to the audio player via Bluetooth Random play Press and hold 3 to select [ALL RANDOM] or [GROUP RANDOM]*. Select a file from a folder/list Refer to “Select a file to play” on page 13.
AMAZON ALEXA (for / / / Alexa is the cloud-based voice service developed by Amazon. You can ask Alexa to play music, get weather reports, traffic information, control smart home devices, shop on Amazon, search the internet, set reminders and more. Preparation: • Create an account at , or use the Alexa mobile application. • After installing the latest version of the Alexa mobile application on your device, log in using those credentials.
AMAZON (for ALEXA / / / / / / ) • To return to the previous source before ALEXA, press B SRC (or press SRC on the remote control). • To activate Alexa, press . • To cancel current listening state, press . • To cancel current thinking/speaking states and go to listening state, press . • Only one Alexa connection can be connected at one time. • “DISCONNECTED” appears if the unit is disconnected from Alexa mobile application or the Bluetooth connection is disconnected.
Audio Settings [MANUAL EQ] [62.5HZ] Adjusts your own sound settings for each source. • The settings are stored to [USER] in [PRESET EQ]. • The settings made may affect the current settings of [EASY EQ]. [LEVEL] [LEVEL –9] to [LEVEL +9] ([LEVEL 0]): Adjusts the level to memorize for each source. (Before making an adjustment, select the source you want to adjust.) [SOUND EFFECT] [SOUND RECNSTR] (Sound reconstruction) (Not applicable for RADIO source, AUX source and SIRIUS XM source.
Audio Settings [X ‘ OVER] [TWEETER] [FRONT HPF] [REAR HPF] [FRQ] [1KHZ]/[1.6KHZ]/[2.5KHZ]/[4KHZ]/[5KHZ]/ [6.3KHZ]/[8KHZ]/[10KHZ]/[12.5KHZ]: Adjusts the crossover frequency for the tweeter speaker. [GAIN LEFT] [–8] to [0]: Adjusts the output volume of the left tweeter. [GAIN RIGHT] [–8] to [0]: Adjusts the output volume of the right tweeter.
Audio Settings Digital Time Alignment settings Digital Time Alignment sets the delay time of the speaker output to create a more suitable environment for your vehicle. • For more information, see the following “Determining the delay time automatically”.
Display Settings Zone identification for color settings and brightness settings Change the display settings 1 Press the volume knob to enter [FUNCTION]. 2 Turn the volume knob to select an item (see the following table), then press the knob. 3 Repeat step 2 until the desired item is selected/activated or follow the instructions stated on the selected item. to exit. 4 Press and hold To return to the previous setting item, press Zone identification for brightness setting .
Display Settings [DIMMER] [BRIGHTNESS] Dims the illumination. [ON]: Dimmer is turned on. [OFF]: Dimmer is turned off. [DIMMER TIME]: Set the time to turn on dimmer and to turn off dimmer. 1 Turn the volume knob to adjust the [ON] time, then press the knob. 2 Turn the volume knob to adjust the [OFF] time, then press the knob. Default: [ON]: [6:00PM] ; [OFF]: [6:00AM] Sets the brightness for day and night separately. 1 [DAY]/[NIGHT]: Select day or night. 2 Select a zone. (See the illustration on page 33.
Learning Steering Remote Control (for You can control the unit with the steering remote control keys on your vehicle. After connection, you can configure the control keys according to your preference. • You can only make this configuration if your vehicle is equipped with the electrical steering remote control. • If the steering remote control in your car is not compatible, configuration may not be completed and an error message may appear.
Installation/Connection This section is for the professional installer. For safety’s sake, leave wiring and mounting to professionals. Consult the car audio dealer. Part list for installation (A) Faceplate (×1) (B) Trim plate (×1) (C) Mounting sleeve (×1) (D) Wiring harness (×1) (E) Extraction key (×2) (F) Screws* WARNING • The unit can only be used with a 12 V DC power supply, negative ground. • Disconnect the battery’s negative terminal before wiring and mounting.
Installation/Connection Installing the unit (in-dash mounting) Installing the unit (without mounting sleeve) 1 Remove the mounting sleeve and trim plate from the unit. 2 Align the holes in the unit (on both sides) with the vehicle mounting bracket and secure the unit with screws (supplied/commercially available). Use only the specified screws. Using wrong screws might damage the unit. Do the required wiring. (Page 38) Removing the unit 1 Detach the faceplate.
Installation/Connection Wiring connection IMPORTANT We recommend installing the unit with a commercially available custom wiring harness specific for your car and leave this job to professionals for your safety. Consult your car audio dealer. Fuse (10 A) Antenna terminal White To front speaker (left) Gray To front speaker (right) Gray/Black Green To rear speaker (left) To rear speaker (right) Ignition switch If no connections are made, do not let the wire come out from the tab.
Installation/Connection Connect external components Connect external amplifiers via output terminals When connecting to an external amplifier to the output terminals of this unit, firmly connect the ground wire of the amplifier to the car’s chassis to avoid damaging the unit.
References Maintenance Cleaning the unit Wipe off dirt on the faceplate with a dry silicone or soft cloth. Cleaning the connector Detach the faceplate and clean the connector gently with a cotton swab. Be careful not to damage the connector. Connector (on the reverse side of the faceplate) Handling discs • Do not touch the recording surface of the disc. • Do not stick tape etc. on the disc, or use a disc with tape stuck on it. • Do not use any accessories for the disc.
References About Pandora • Pandora is only available in certain countries. For more information, visit . • Because Pandora is a third-party service, the specifications are subject to change without prior notice. Accordingly, compatibility may be impaired, or some or all of the services may become unavailable. • Some functions of Pandora cannot be operated from this unit. • For issues using the application, please contact Pandora at .
References Change the display information (For / / / / / ) Each time you press DISP, the display information changes. • If the information is unavailable or not recorded, “NO TEXT”, “NO INFO”, or other information (eg. station name) appears or display will be blank.
References (For / / ) Each time you press DISP, the display information changes. • If the information is unavailable or not recorded, “NO TEXT”, “NO INFO”, or other information (eg. station name) appears or display will be blank.
Troubleshooting Symptom Remedy General “MISWIRING CHECK WIRING THEN PWR ON” appears. HD Radio Tuner/Radio Turn the power off, then check to be sure the terminals of the speaker wires are insulated properly. Turn the power on again. “PROTECTING SEND SERVICE” appears. Send the unit to the nearest service center. Source cannot be selected. Check the [SOURCE SELECT] setting. (Page 6) • Sound cannot be heard. • The unit does not turn on. • Information shown on the display is incorrect.
Troubleshooting This unit is still preparing the iPod/iPhone music list. It may take some time to load, try again later. “NO DISC” Insert a playable disc into the loading slot. “TOC ERROR” Make sure the disc is clean and inserted properly. “NA FILE” Make sure the media (disc/USB) contain supported audio files. (Page 40) “COPY PRO” A copy-protected file is played (disc/USB). “NO DEVICE” Connect a device (USB/iPod/iPhone), and change the source to USB/iPod USB again.
Troubleshooting Bluetooth® 46 Remedy “NO SIGNAL” Make sure the antenna is mounted outside the vehicle. “SUBSCRIPTION UPDATED – PRESS ENTER TO CONTINUE.” Your subscription is updated. Press the volume knob to continue. “CODE ERROR” Make sure you have entered the correct pass code. (Page 19) “NO CONTENT” There is insufficient content to start TuneScan. “SCAN CANCEL” TuneScan has been aborted. No Bluetooth device is detected. • Search from the Bluetooth device again. • Reset the unit.
Specifications Troubleshooting Remedy No response from Alexa after the voice input. Amazon cloud was unable to analyze the voice input. Wrong response from Alexa. Alexa misunderstood what was said or did not catch the entire request or sentence spoken. Please try again. (Page 28) “DISCONNECTED” Be sure to connect your smartphone to the unit via Bluetooth. (Page 22) Not able to connect or reconnect to Alexa mobile application. • Be sure the audio device is connected via Bluetooth.
Specifications / / / FM / / / : Frequency Range / / / / / : 87.9 MHz — 107.9 MHz (200 kHz step) AM Usable Sensitivity (S/N = 30 dB) 8.2 dBf (0.71 μV/75 Ω) Quieting Sensitivity (DIN S/N = 46 dB) 17.2 dBf (2.0 μV/75 Ω) Frequency Response (±3 dB) 30 Hz — 15 kHz Signal-to-Noise Ratio (MONO) 64 dB Stereo Separation (1 kHz) 40 dB Frequency Range 530 kHz — 1 700 kHz (10 kHz step) Usable Sensitivity (S/N = 20 dB) 29 dBμ (28.
Specifications / : Auxiliary Channel Separation 89 dB / 20 Hz — 20 kHz Input Maximum Voltage 1 000 mV Input Impedance 30 kΩ Version Bluetooth 4.2 / MP3 Decode Compliant with MPEG-1/2 Audio Layer-3 WMA Decode Compliant with Windows Media Audio AAC Decode AAC-LC “.aac” files USB Standard USB 1.1, USB 2.
Specifications Band 1: 62.5 Hz ±9 dB Band 2: 100 Hz ±9 dB Band 3: 160 Hz ±9 dB Band 4: 250 Hz ±9 dB Band 5: 400 Hz ±9 dB Band 6: 630 Hz ±9 dB Band 7: 1 kHz ±9 dB Band 8: 1.6 kHz ±9 dB Band 9: 2.5 kHz ±9 dB Band 10: 4 kHz ±9 dB Band 11: 6.
libFLAC Copyright (C) 2000-2009 Josh Coalson Copyright (C) 2011-2013 Xiph.Org Foundation Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: - Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
ENGLISH FRANÇAIS ESPAÑOL KDC-BT278U CD-RECEIVER For detailed operations and information, refer to the INSTRUCTION MANUAL on the following website: Pour les opérations et les informations détaillées, reportez-vous au MODE D’EMPLOI sur le site web suivant: Para obtener más información y detalles sobre las operaciones, consulte el MANUAL DE INSTRUCCIONES en el siguiente sitio web: Quick Start Guide AUTORADIO CD Guide de démarrage rapide RECEPTOR CD Guía de inicio rápido For your records Record the serial
CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. In compliance with Federal Regulations, following are reproductions of labels on, or inside the product relating to laser product safety. JVCKENWOOD Corporation 2967-3, ISHIKAWA-MACHI, HACHIOJI-SHI, TOKYO, JAPAN THIS PRODUCT COMPLIES WITH DHHS RULES 21CFR SUBCHAPTER J IN EFFECT AT DATE OF MANUFACTURE.
IC (Industry Canada) Caution This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference, including interference that may cause undesired operation of the device.
Article 4 Right pertaining to the Licensed Software Any and all copyrights and other rights pertaining to the Licensed Software and related documents shall belong to the Licensor or the original holder of the right who granted to the Licensor the license or sublicense for the Licensed Software (hereinafter the "Original Rightholder"), and the User shall not be entitled to any right other than the license granted hereunder, in respect of the Licensed Software and any related documents. Article 5 1. 2. 2.
Important Notice concerning the Software -CMP -jansson The MIT License (MIT) Copyright (c) 2014 Charles Gunyon Copyright (c) 2009-2012 Petri Lehtinen
Installation/Connection This section is for the professional installer. For safety’s sake, leave wiring and mounting to professionals. Consult the car audio dealer. WARNING • The unit can only be used with a 12 V DC power supply, negative ground. • Disconnect the battery’s negative terminal before wiring and mounting. • Do not connect Battery wire (yellow) and Ignition wire (red) to the car chassis or Ground wire (black) to prevent a short circuit.
Installing the unit (without mounting sleeve) 1 Remove the mounting sleeve and trim plate from the unit. 2 Align the holes in the unit (on both sides) with the vehicle mounting bracket and secure the unit with screws (commercially available). Wiring connection Antenna terminal Fuse (10 A) Use only the specified screws. Using wrong screws might damage the unit. If no connections are made, do not let the wire come out from the tab.
Before Use Basics IMPORTANT Faceplate • To ensure proper use, please read through this Guide before using this product. It is especially important that you read and observe Warnings and Cautions in this Guide. • Please keep the Guide in a safe and accessible place for future reference. Volume knob Loading slot USB input terminal WARNING Auxiliary input jack Do not operate any function that takes your attention away from safe driving.
9 Turn the volume knob to select [DATE SET], then press the knob. 10 Turn the volume knob to make the settings, then press the knob. Getting Started 1 Select the display language and cancel the demonstration When you turn on the power for the first time (or [FACTORY RESET] is set to [YES]), the display shows: “SEL LANGUAGE” “PRESS” “VOLUME KNOB” 1 Turn the volume knob to select [ENG] (English) / [SPA] (Spanish) / [FRE] (French), then press the knob. [ENG] is selected for the initial setup.
Radio CD/USB/iPod Search for a station 1 Press B SRC repeatedly to select RADIO. 2 Press BAND repeatedly to select FM1/FM2/FM3/AM. 3 Press S / T to search for a station. Settings in memory You can store up to 18 stations for FM and 6 stations for AM. Start playback The source changes automatically and playback starts when you load a disc or attach a device (USB device/ iPod/iPhone) to the USB input terminal. To On the faceplate Play back/pause Press 6 IW. .
Functions Settings Examples of some well-used settings 1 2 3 4 1 Press the volume knob to enter [FUNCTION]. Subwoofer Level Setting Press the volume knob to enter [FUNCTION]. Turn the volume knob to select an item, then press the knob. Repeat step 2 until the desired item is selected or activated. Press and hold to exit. To return to the previous setting item, press . • Refer to the INSTRUCTION MANUAL on the following website for the detailed explanation of each item:
Once pairing is completed, Bluetooth connection is established automatically. • “BT1” and/or “BT2” indicator on the display window lights up. Bluetooth® • Depending on the Bluetooth version, operating system and the firmware version of your mobile phone, Bluetooth features may not work with this unit. • Be sure to turn on the Bluetooth function of the device to make the following operations. • Signal conditions vary depending on the surroundings.
Other Information For playback operations of AUX, Spotify, Pandora® sources, refer to the INSTRUCTION MANUAL on the following website: • The availability of each source vary depending on the model. Note for specifications Bluetooth Frequency Range: 2.402 GHz — 2.480 GHz Bluetooth RF Output Power (E.I.R.P.): +4 dBm (MAX), Power Class 2 Speaker Impedance: 4Ω—8Ω Operating Voltage: 12 V DC car battery 9 JS_KWD_QSG_KDC_BT278U_KN_EN.
• Microsoft and Windows Media are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. • Use of the Made for Apple badge means that an accessory has been designed to connect specifically to the Apple product(s) identified in the badge and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards.
MILITARY Units purchased through the U.SA m1htary exchange seMCe OYffleaS may be serviced under warranty in the continental U.SA, subiect to the tottow,ng cood1tions 1) The ongmat warranty is in effect. 2) Proof of purchase ~ provided to the servicer. LIMITATION OF IMPLIED WARRANTIES Arri and all implied warranties, Including warranties of mercflantabllity and filness for a partlCUlar purpose, sllall be hm,led in duration to the length of th~ warranty. WARRANTY FOR MILITARY MARKET .
U.S.A. CANADA JVCKENWOOD USA Corporation Th,s warranty will be honored only in lhe U.S.A. WHO IS PROTECTED This warranty is enforceable only by lhe original purchaser. KENWOOD LIMITED WARRANTY FOR CAR STEREO COMPONENTS WHAT WE WILL PAY FOR We will pay tor all labor and mater~I expenses tor covered items. Payroont of shipping charges is discussed in lhe next section of this warranty.
