KDC-X500 KDC-BT565U KMR-D765BT CD-RECEIVER INSTRUCTION MANUAL AMPLI-TUNER LECTEUR DE CD MODE D’EMPLOI REPRODUCTOR DE DISCOS COMPACTOS RECEPTOR DE FM/AM MANUAL DE INSTRUCCIONES For your records Record the serial number, found on the back of the unit, in the spaces designated on the warranty card, and in the space provided below. Refer to the model and serial numbers whenever you call upon your Kenwood dealer for information or service on the product.
CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. In compliance with Federal Regulations, following are reproductions of labels on, or inside the product relating to laser product safety. JVC KENWOOD Corporation 2967-3, ISHIKAWA-MACHI, HACHIOJI-SHI, TOKYO, JAPAN THIS PRODUCT COMPLIES WITH DHHS RULES 21CFR SUBCHAPTER J IN EFFECT AT DATE OF MANUFACTURE.
IC (Industry Canada) Notice This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. The term “IC: ” before the certification/ registration number only signifies that the Industry Canada technical specification were met.
SOFTWARE LICENSE AGREEMENT The software embedded in the Product (hereinafter the "Licensed Software") provided by Licensor is copyrighted to or sublicensable by the Licensor, and this Agreement provides for the terms and conditions which Users shall follow in order to use the Licensed Software. The User shall use the Licensed Software by agreeing with the terms of this Software License Agreement.
Article 8 Termination In case the User falls under any of the events described in the following items, the Licensor may immediately terminate this Agreement or claim that the User compensates for the damage incurred by the Licensor due to such event: (1) when the User violated any provision of this Agreement; or (2) when a petition has been filed against the User for an attachment, provisional attachment, provisional disposition or any other compulsory execution.
CONTENTS BEFORE USE BEFORE USE 2 BASICS 3 GETTING STARTED 4 1 Select the display language and cancel the demonstration 2 Set the clock and date 3 Set the initial settings RADIO 6 CD / USB / iPod / ANDROID 7 AUX 9 Pandora® 10 iHeartRadio® 11 SiriusXM® Radio 12 BLUETOOTH® 15 AUDIO SETTINGS 21 DISPLAY SETTINGS 23 REFERENCES 24 Maintenance More information TROUBLESHOOTING 26 SPECIFICATIONS 28 INSTALLATION / CONNECTION 30 IMPORTANT • To ensure proper use, please read through t
BASICS Faceplate Volume knob Display window Remote control (RC-406) (supplied for ) / Remote sensor (Do not expose to bright sunlight.) Pull out the insulation sheet when using for the first time. : USB cable from the rear of the unit Detach button Attach Detach How to reset Remote control functions are not available for . How to replace the battery Press the switch twice within 5 seconds after detaching the faceplate. To On the faceplate On the remote control Turn on the power .
GETTING STARTED 1 Select the display language and cancel the demonstration When you turn on the power for the first time (or [FACTORY RESET] is set to [YES], 5), the display shows: “SEL LANGUAGE” “PRESS” “VOLUME KNOB” 1 (For / / ) Turn the volume knob to select [ENG] (English) or [SPA] (Spanish), then press the knob. [ENG] is selected for the initial setup. (For / ) Then, the display shows: “CANCEL DEMO” “PRESS” “VOLUME KNOB”. 2 Press the volume knob. [YES] is selected for the initial setup.
GETTING STARTED CLOCK SYSTEM ON: Activates the keypress tone. ; OFF: Deactivates. CLOCK DISPLAY (For / ) ON: The clock time is shown on the display even when the unit is turned off. ; OFF: Cancels. PANDORA SRC ON: Enables PANDORA/ PANDORA FRONT/ PANDORA REAR in source selection. ; OFF: Disables. ( 10) DATE SET ) (For DD/MM/YY: Sets the date for marine remote control display. IHEART SRC ON: Enables IHEARTRADIO/ IHEART FRONT/ IHEART REAR in source selection. ; OFF: Disables.
RADIO Other settings 1 Press the volume knob to enter [FUNCTION]. 2 Turn the volume knob to select an item (see the following table), then press the knob. 3 Repeat step 2 until the desired item is selected or activated. 4 Press and hold to exit. To return to the previous setting item, press Search for a station repeatedly to select TUNER. 1 Press 2 Press repeatedly (or press / on RC-406) to select FM1/ FM2/ FM3/ AM. 3 Press S / T (or press S / on RC-406) to search for a station.
CD / USB / iPod / ANDROID Start playback The source changes automatically and playback starts. Label side M Eject disc USB input terminal USB CA-U1EX (max.: 500 mA) (optional accessory) : You can also connect to the USB cable from the rear of the unit. To On the faceplate On the remote control Playback / pause Press Press Reverse / Fast-forward*4 Press and hold S / T. Press and hold S / Select a track/file Press S / T. Press S / Select a folder*5 Press J / K.
CD / USB / iPod / ANDROID Select control mode While in iPod/ iPod FRONT/ iPod REAR source, press 5 repeatedly. MODE ON : Control iPod using the iPod itself. However, you can still play/pause, file skip, fast-forward or reverse from this unit. MODE OFF : Control iPod from this unit. While in ANDROID/ ANDROID FRONT/ ANDROID REAR source, press 5 repeatedly. BROWSE MODE : Control Android device from this unit via KENWOOD MUSIC PLAY application installed in the Android device.
AUX CD / USB / iPod / ANDROID Preparation: Select [ON] for [BUILT-IN AUX]. ( 5) Listen to TuneIn Radio/ TuneIn Radio Pro/ Aupeo While listening to TuneIn Radio, TuneIn Radio Pro or Aupeo, connect the iPod/iPhone to the USB input terminal of the unit. • The unit will output the sound from these applications. Start listening 1 Connect a portable audio player (commercially available). Auxiliary input jack Other settings 1 Press the volume knob to enter [FUNCTION].
Pandora® Preparation: Install the latest version of the Pandora application on your device (iPhone/ iPod touch), then create an account and log in to Pandora. • Select [ON] for [PANDORA SRC]. ( 5) Create and save a new station . 1 Press 2 Turn the volume knob to select [NEW STATION], then press the knob. 3 Turn the volume knob to select [FROM TRACK] or [FROM ARTIST], then Start listening 1 Open the Pandora application on your device. 2 Connect your device to the USB input terminal. press the knob.
Pandora® Delete a station While listening to PANDORA/ PANDORA FRONT/ PANDORA REAR... 1 Press the volume knob to enter [FUNCTION]. 2 Turn the volume knob to select [SYSTEM], then press the knob. 3 Turn the volume knob to select [STATION DEL], then press the knob. 4 Turn the volume knob to select [SORT BY A-Z] or [SORT BY DATE], then press the knob. 5 Turn the volume knob to select the desired station to delete, then press the knob. 6 Turn the volume knob to select [YES], then press the knob.
iHeartRadio® SiriusXM® Radio Search and store a station . 1 Press 2 Turn the volume knob to select a category, Only SiriusXM® brings you more of what you love to listen to, all in one place. Get over 140 channels, including commercial-free music plus the best sports, news, talk, comedy and entertainment. Welcome to the world of satellite radio. A SiriusXM Vehicle Tuner and Subscription are required. For more information, visit www.siriusxm.com. then press the knob.
SiriusXM® Radio 5 Turn the volume knob to select a channel, then press the knob. (or) Press S / T to search for a channel manually. • Pressing and holding S / T changes the channel rapidly. If a locked channel or a mature channel is selected, a pass code input screen appears. Enter the pass code to receive the channel. ( 14) To change the tuning method for S / T: Press .
SiriusXM® Radio Default: XX TuneScan™ You can get a short preview of the songs that you have missed on each of your SmartFavorite music channels or currently tuned music channel. Press and hold to start scanning the first 6 seconds of the recorded music contents. • To listen to the current song, press the volume knob to stop scanning. The unit continues playing the current song. • To select the previous/next song, press S / T. • To cancel scanning, press and hold the volume knob.
BLUETOOTH® BLUETOOTH — Connection Supported Bluetooth profiles – Hands-Free Profile (HFP) – Advanced Audio Distribution Profile (A2DP) – Audio/Video Remote Control Profile (AVRCP) – Serial Port Profile (SPP) – Phonebook Access Profile (PBAP) Supported Bluetooth codecs – Sub Band Codec (SBC) – Advanced Audio Coding (AAC) – aptX Codec (aptX) Connect the microphone MIC (Microphone input terminal) Microphone (supplied) Rear panel Pair and connect a Bluetooth device for the first time to turn on the unit.
BLUETOOTH® Connect with a remote device by One-touch (NFC) (for ) Near Field Communication (NFC) enables short-range wireless communication between the unit and remote devices. By holding an NFC-compatible remote device near to the N-Mark on the unit (volume knob), the unit and remote device proceed to complete pairing and established the BLUETOOTH connection automatically. 1 Activate the NFC function on the remote device. Refer to the instruction manual of the remote device for more information.
BLUETOOTH® To On the faceplate While talking on the first incoming call... Answer another incoming call and hold the current call Press Reject another incoming call Press . . Press . Press . While having two active calls... End current call and activate held call Press Swap between the current call and held call Press Adjust the phone volume [00] to [35] (Default: [15]) Switch between hands-free and private talk modes . . Turn the volume knob during a call.
BLUETOOTH® Make a call NUMBER DIAL 1 Turn the volume knob to select a number (0 to 9) or character ( , #, +). 2 Press S / T to move the entry position. Repeat steps 1 and 2 until you finish entering the phone number. 3 Press the volume knob to call. (or using RC-406) 1 Press the number buttons (0 to 9) to enter the phone number. 2 Press to call. VOICE Speak the name of the contact you want to call or the voice command to control the phone functions.
BLUETOOTH® Default: XX Settings in memory Store a contact in memory You can store up to 6 contacts into the number buttons (1 to 6). 1 Press to enter Bluetooth mode. 2 Turn the volume knob to select [CALL HISTORY], [PHONE BOOK], or [NUMBER DIAL], then press the knob. 3 Turn the volume knob to select a contact or enter a phone number. If a contact is selected, press the volume knob to show the phone number. 4 Press and hold one of the number buttons (1 to 6). “STORED” appears when the contact is stored.
BLUETOOTH® BLUETOOTH — Audio Bluetooth test mode You can check the connectivity of the supported profile between the Bluetooth device and the unit. • Make sure there is no Bluetooth device paired. 1 Press and hold . “PLEASE PAIR YOUR PHONE PIN 0000” appears. 2 Search and select this unit model name (KDC-X5 / KDC-BT5 U/ KMR-D7 BT) on the Bluetooth device. 3 Operate the Bluetooth device to confirm pairing. “TESTING” flashes on the display.
BLUETOOTH® Internet radio via Bluetooth Listen to Pandora You can listen to Pandora on the Android device via Bluetooth on this unit. Preparation: Select [ON] for [PANDORA SRC]. ( 5) 1 Open the Pandora application on your device. 2 Connect your Bluetooth audio player via Bluetooth connection. ( 15) 3 Press repeatedly to select PANDORA. The source switches and broadcast starts automatically. You can operate Pandora in the same way as Pandora for iPod/iPhone.
AUDIO SETTINGS VOLUME OFFSET –15 to +6 (0): Preset the initial volume level of each source. (Before adjustment, select the source you want to adjust.) X ' OVER TWEETER FRQ 1KHZ/ 1.6KHZ/ 2.5KHZ/ 4KHZ/ 5KHZ/ 6.3KHZ/ 8KHZ/ 10KHZ/ 12.5KHZ: Adjusts the crossover frequency for the tweeter speaker. GAIN LEFT –8 to 0: Adjusts the output volume of the left tweeter. GAIN RIGHT –8 to 0: Adjusts the output volume of the right tweeter.
DISPLAY SETTINGS Default: XX : ZONE 1 : ZONE 2 COLOR SELECT VARIABLE SCAN/ CUSTOM R/G/B/ preset colors*: Selects your preferred button and display illumination color. To make your own color, select [CUSTOM R/G/B]. The color you have made will be stored in [CUSTOM R/G/B]. 1 Press the volume knob to enter the detailed color adjustment. 2 Press S / T to select the color (R/ G/ B) to adjust. 3 Turn the volume knob to adjust the level (0 — 9), then press the knob.
REFERENCES Maintenance Cleaning the unit Wipe off dirt on the faceplate with a dry silicone or soft cloth. Cleaning the connector Detach the faceplate and clean the connector gently with a cotton swab, being careful not to damage the connector. Connector (on the reverse side of the faceplate) Handling discs • Do not touch the recording surface of the disc. • Do not stick tape etc. on the disc, or use a disc with tape stuck on it. • Do not use any accessories for the disc.
REFERENCES About Pandora • Pandora is only available in certain countries. Please visit for more information. • Because Pandora is a third-party service, the specifications are subject to change without prior notice. Accordingly, compatibility may be impaired, or some or all of the services may become unavailable. • Some functions of Pandora cannot be operated from this unit. • For issues using the application, please contact Pandora at pandora-support@pandora.com.
TROUBLESHOOTING Sound cannot be heard. • Adjust the volume to the optimum level. • Check the cords and connections. “MISWIRING CHECK WIRING THEN PWR ON” appears. Turn the power off, then check to be sure the terminals of the speaker wires are insulated properly. Turn the power on again. “PROTECTING SEND SERVICE” appears. Send the unit to the nearest service center. • Sound cannot be heard. • The unit does not turn on. • Information shown on the display is incorrect. Clean the connectors.
TROUBLESHOOTING Pandora “NO DEVICE” or “READING” keeps flashing. • Switch off the developer options on the Android device. • Reconnect the Android device. • If this does not solve the problem, the connected Android device does not support [BROWSE MODE]. ( 24) Playback is intermittent or sound skips. Turn off the power saving mode on the Android device. “ANDROID ERROR” / “NA DEVICE” • Reconnect the Android device. • Restart the Android device. “ADD ERROR” New station creation is unsuccessful.
SPECIFICATIONS TROUBLESHOOTING Remedy • Adjust the microphone unit’s position. ( 15) • Check the [ECHO CANCEL] setting. ( 17) Phone sound quality is poor. • Reduce the distance between the unit and the Bluetooth device. • Move the car to a place where you can get a better signal reception. Voice calling method is not successful. • Use voice calling method in a more quiet environment. • Reduce the distance from the microphone when you speak the name.
MP3 Decode Compliant with MPEG-1/2 Audio Layer-3 Maximum Output Power 50 W × 4 WMA Decode Compliant with Windows Media Audio 22 W × 4 AAC Decode AAC-LC “.aac” files Full Bandwidth Power (at less than 1 % THD) Speaker Impedance 4Ω—8Ω USB Standard USB 1.1, USB 2.0 (Full speed) Tone Action File System FAT12/ 16/ 32 Maximum Supply Current DC 5 V MP3 Decode Compliant with MPEG-1/2 Audio Layer-3 WMA Decode Compliant with Windows Media Audio AAC Decode AAC-LC “.
INSTALLATION / CONNECTION Warning • The unit can only be used with a 12 V DC power supply, negative ground. • Disconnect the battery’s negative terminal before wiring and mounting. • Do not connect Battery wire (yellow) and Ignition wire (red) to the car chassis or Ground wire (black) to prevent a short circuit. • Insulate unconnected wires with vinyl tape to prevent a short circuit. • Be sure to ground this unit to the car’s chassis again after installation.
Wiring connection (for / ) Part list for installation IMPORTANT : We recommend installing the unit with a commercially available custom wiring harness specific for your car and leave this job to professionals for your safety. Consult your car audio dealer. (A) Faceplate When connecting to an external amplifier, connect its ground wire to the car’s chassis to avoid damaging the unit.
Wiring connection (for ) IMPORTANT : We recommend installing the unit with a commercially available custom wiring harness specific for your car and leave this job to professionals for your safety. Consult your car audio dealer. MIC (Microphone input terminal) ( 15) To the remote control, KCA-RC55MR (optional accessory) When connecting to an external amplifier, connect its ground wire to the car’s chassis to avoid damaging the unit. USB cable (DC 5 V 1.
• “Made for iPod,” and “Made for iPhone” mean that an electronic accessory has been designed to connect specifically to iPod, or iPhone, respectively, and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. Please note that the use of this accessory with iPod or iPhone may affect wireless performance.
