KMM-BT515HD KMM-BT315U KMM-BT315 KMR-M315BT DIGITAL MEDIA RECEIVER INSTRUCTION MANUAL RÉCEPTEUR MULTIMÉDIA NUMÉRIQUE MODE D’EMPLOI RECEPTOR DE MEDIOS DIGITALES MANUAL DE INSTRUCCIONES For your records Record the serial number, found on the back of the unit, in the spaces designated on the warranty card, and in the space provided below. Refer to the model and serial numbers whenever you call upon your Kenwood dealer for information or service on the product.
FCC WARNING This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made. FCC NOTE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
IC (Industry Canada) Notice This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. The term “IC: ” before the certification/ registration number only signifies that the Industry Canada technical specification were met.
SOFTWARE LICENSE AGREEMENT The software embedded in the Product (hereinafter the "Licensed Software") provided by Licensor is copyrighted to or sublicensable by the Licensor, and this Agreement provides for the terms and conditions which Users shall follow in order to use the Licensed Software. The User shall use the Licensed Software by agreeing with the terms of this Software License Agreement.
Article 8 Termination In case the User falls under any of the events described in the following items, the Licensor may immediately terminate this Agreement or claim that the User compensates for the damage incurred by the Licensor due to such event: (1) when the User violated any provision of this Agreement; or (2) when a petition has been filed against the User for an attachment, provisional attachment, provisional disposition or any other compulsory execution.
CONTENTS BEFORE USE BEFORE USE 2 IMPORTANT BASICS 3 GETTING STARTED 4 • To ensure proper use, please read through this manual before using this product. It is especially important that you read and observe Warning and Caution in this manual. • Please keep the manual in a safe and accessible place for future reference.
BASICS Faceplate Remote control (RC-406) Lights up when Bluetooth connection is established. ( 16) Display window Remote sensor (Do not expose to bright sunlight.) Pull out the insulation sheet when using for the first time. Detach button Volume knob Attach Detach Flashes when the unit enters searching status. How to reset : Remote control functions are not available. How to replace the battery Press the switch twice within 5 seconds after detaching the faceplate.
GETTING STARTED 1 Select the display language and cancel the demonstration When you turn on the power for the first time (or [FACTORY RESET] is set to [YES], 5), the display shows: “SEL LANGUAGE” “PRESS” “VOLUME KNOB” 1 Turn the volume knob to select [ENG] (English) or [SPA] (Spanish), then press the knob. [ENG] is selected for the initial setup. (For / / ) Then, the display shows: “CANCEL DEMO” “PRESS” “VOLUME KNOB”. 2 Press the volume knob. [YES] is selected for the initial setup.
GETTING STARTED CLOCK TUNER SETTING PRESET TYPE NORMAL: Memorizes one station for each preset button in each band (FM1/ FM2/ FM3/ AM). ; MIX: Memorizes one station or SiriusXM channel for each preset button, regardless of the selected band or SiriusXM channel. CLOCK DISPLAY / / ) ON: The clock time is shown on the display even when the unit is turned off. ; OFF: Cancels. ON: Activates the keypress tone. ; OFF: Deactivates. DATE SET (For ) DD/MM/YY: Sets the date for marine remote control display.
HD Radio™ tuner (for ) You can tune in to both conventional and HD Radio broadcasts. • To find HD Radio stations in your area, visit . Select an HD Radio multicast channel Many HD Radio stations offer more than one channel programming. This service is called multicasting. While receiving HD Radio multicast channels.... Press S / T to select your desired channel (HD1 to HD8). “LINKING” appears while linking to a multicast channel.
RADIO (for / / ) Other settings 1 Press the volume knob to enter [FUNCTION]. 2 Turn the volume knob to select an item (see the following table), then press the knob. 3 Repeat step 2 until the desired item is selected or activated. 4 Press and hold to exit. To return to the previous setting item, press Search for a station repeatedly to select TUNER. 1 Press 2 Press repeatedly (or press / Default: XX on RC-406) to select FM1/ FM2/ FM3/ AM.
RADIO (for / / ) Preparation: Select [ON] for [BUILT-IN AUX]. ( 5) CLOCK TIME SYNC AUX ON: Synchronizes the unit’s time to the Radio Broadcast Data System/ Radio Data System station time. ; OFF: Cancels.
USB / iPod / ANDROID Start playback The source changes automatically and playback starts. USB input terminal USB CA-U1EX (max.: 500 mA) (optional accessory) iPod/iPhone KCA-iP102 / KCA-iP103 (optional accessory)*1 or accessory cable of the iPod/iPhone*2 ANDROID*3 To On the faceplate On the remote control Playback / pause Press Press Reverse / Fast-forward*4 Press and hold S / T. Press and hold S / Select a track/file Press S / T. Press S / Select a folder*5 Press J / K.
USB / iPod / ANDROID Select control mode While in IPOD source, press 5 repeatedly. MODE ON : Control iPod using the iPod itself. However, you can still play/pause, file skip, fast-forward or reverse from this unit. MODE OFF : Control iPod from this unit. While in ANDROID source, press 5 repeatedly. BROWSE MODE : Control Android device from this unit via KENWOOD MUSIC PLAY application installed in the Android device.
Pandora® (for USB / iPod / ANDROID / ) Preparation: Install the latest version of the Pandora application on your device (iPhone/ iPod touch), then create an account and log in to Pandora. • Select [ON] for [PANDORA SRC]. ( 5) Direct Music Search (using RC-406) (except for / ) 1 Press DIRECT. 2 Press the number buttons to enter a track/file Start listening 1 Open the Pandora application on your device. 2 Connect your device to the USB input terminal. number. 3 Press to search for music. or DIRECT.
Pandora® (for / / ) Search for a registered station . 1 Press 2 Turn the volume knob to select an item, then press the knob. [SORT BY DATE]: According to the registered date [SORT BY A-Z]: Alphabetical order 3 Turn the volume knob to select the desired station, then press the knob. To cancel, press and hold . (or using RC-406) (except ) . Press J / K to search for a station, then press iHeartRadio® (for Delete a station While listening to PANDORA... 1 Press the volume knob to enter [FUNCTION].
iHeartRadio® (for / / ) Search and store a station . 1 Press 2 Turn the volume knob to select a category, SiriusXM® Radio (for / / ) Only SiriusXM® brings you more of what you love to listen to, all in one place. Get over 140 channels, including commercial-free music plus the best sports, news, talk, comedy and entertainment. Welcome to the world of satellite radio. A SiriusXM Vehicle Tuner and Subscription are required. For more information, visit www.siriusxm.com. then press the knob.
SiriusXM® Radio (for / / 5 Turn the volume knob to select a channel, then press the knob. (or) Press S / T to search for a channel manually. • Pressing and holding S / T changes the channel rapidly. If a locked channel or a mature channel is selected, a pass code input screen appears. Enter the pass code to receive the channel. ( 15) To change the tuning method for S / T: Press .
SiriusXM® Radio (for / / ) Default: XX TuneScan™ You can get a short preview of the songs that you have missed on each of your SmartFavorite music channels or currently tuned music channel. Press and hold to start scanning the first 6 seconds of the recorded music contents. • To listen to the current song, press the volume knob to stop scanning. The unit continues playing the current song. • To select the previous/next song, press S / T. • To cancel scanning, press and hold the volume knob.
BLUETOOTH® BLUETOOTH — Connection Supported Bluetooth profiles – Hands-Free Profile (HFP) – Advanced Audio Distribution Profile (A2DP) – Audio/Video Remote Control Profile (AVRCP) – Serial Port Profile (SPP) – Phonebook Access Profile (PBAP) Supported Bluetooth codecs – Sub Band Codec (SBC) – Advanced Audio Coding (AAC) – aptX Codec (aptX) (for / / ) Connect the microphone Pair and connect a Bluetooth device for the first time to turn on the unit.
BLUETOOTH® Connect with a remote device by One-touch (NFC) (for ) Near Field Communication (NFC) enables short-range wireless communication between the unit and remote devices. By holding an NFC-compatible remote device near to the N-Mark on the unit (volume knob), the unit and remote device proceed to complete pairing and established the BLUETOOTH connection automatically. 1 Activate the NFC function on the remote device. Refer to the instruction manual of the remote device for more information.
BLUETOOTH® To On the faceplate While talking on the first incoming call... Answer another incoming call and hold the current call Press Reject another incoming call Press End current call and activate held call Press Swap between the current call and held call Press . Default: XX On the remote control Press . . Press . . Press . Press . MIC GAIN –10 — +10 (–4): The sensitivity of the microphone increases as the number increased.
BLUETOOTH® Make a call NUMBER DIAL 1 Turn the volume knob to select a number (0 to 9) or character ( , #, +). 2 Press S / T to move the entry position. Repeat steps 1 and 2 until you finish entering the phone number. 3 Press the volume knob to call. (or using RC-406) (except ) 1 Press the number buttons (0 to 9) to enter the phone number. 2 Press to call. VOICE Speak the name of the contact you want to call or the voice command to control the phone functions.
BLUETOOTH® Default: XX Settings in memory Store a contact in memory You can store up to 6 contacts into the number buttons (1 to 6). 1 Press to enter Bluetooth mode. 2 Turn the volume knob to select [CALL HISTORY], [PHONE BOOK], or [NUMBER DIAL], then press the knob. 3 Turn the volume knob to select a contact or enter a phone number. If a contact is selected, press the volume knob to show the phone number. 4 Press and hold one of the number buttons (1 to 6). “STORED” appears when the contact is stored.
BLUETOOTH® BLUETOOTH — Audio Bluetooth test mode You can check the connectivity of the supported profile between the Bluetooth device and the unit. • Make sure there is no Bluetooth device paired. 1 Press and hold . “PLEASE PAIR YOUR PHONE PIN 0000” appears. 2 Search and select this unit model name (KMM-BT51 HD/ KMM-BT31 U/ KMM-BT31 / KMR-M31 BT) on the Bluetooth device. 3 Operate the Bluetooth device to confirm pairing. “TESTING” flashes on the display.
AUDIO SETTINGS BLUETOOTH® Internet radio via Bluetooth (for / / ) Listen to Pandora You can listen to Pandora on the Android device via Bluetooth on this unit. Preparation: Select [ON] for [PANDORA SRC]. ( 5) 1 Open the Pandora application on your device. 2 Connect your Bluetooth audio player via Bluetooth connection. ( 16) 3 Press repeatedly to select PANDORA. The source switches and broadcast starts automatically. You can operate Pandora in the same way as Pandora for iPod/iPhone.
AUDIO SETTINGS VOLUME OFFSET –15 to +6 (0): Preset the initial volume level of each source. (Before adjustment, select the source you want to adjust.) X ' OVER TWEETER FRQ 1KHZ/ 1.6KHZ/ 2.5KHZ/ 4KHZ/ 5KHZ/ 6.3KHZ/ 8KHZ/ 10KHZ/ 12.5KHZ: Adjusts the crossover frequency for the tweeter speaker. GAIN LEFT –8 to 0: Adjusts the output volume of the left tweeter. GAIN RIGHT –8 to 0: Adjusts the output volume of the right tweeter.
DISPLAY SETTINGS Default: XX COLOR SELECT Select color for ALL ZONE, ZONE 1 and ZONE 2 separately. 1 Select a zone. 2 Select a color for the selected zone. VARIABLE SCAN/ CUSTOM R/G/B/ preset colors* Default: / / : VARIABLE SCAN : CUSTOM R/G/B (R = 9/ G = 9/ B = 9) To make your own color, select [CUSTOM R/G/B]. The color you have made will be stored in [CUSTOM R/G/B]. 1 Press the volume knob to enter the detailed color adjustment. 2 Press S / T to select the color (R/ G/ B) to adjust.
TROUBLESHOOTING Sound cannot be heard. • Adjust the volume to the optimum level. • Check the cords and connections. “MISWIRING CHECK WIRING THEN PWR ON” appears. Turn the power off, then check to be sure the terminals of the speaker wires are insulated properly. Turn the power on again. “PROTECTING SEND SERVICE” appears. Send the unit to the nearest service center. • Sound cannot be heard. • The unit does not turn on. • Information shown on the display is incorrect. Clean the connectors.
TROUBLESHOOTING Pandora • Make sure KENWOOD MUSIC PLAY APP is installed on the Android device. ( 9) • Reconnect the Android device and select the appropriate control mode. • If this does not solve the problem, the connected Android device does not support [BROWSE MODE]. ( 28) Symptom Remedy iHeartRadio station cannot be selected. If “Explicit Content” in [Account Settings] is checked in the web version of iHeartRADIO, custom stations become unavailable.
TROUBLESHOOTING Bluetooth® Remedy No Bluetooth device is detected. • Search from the Bluetooth device again. • Reset the unit. ( 3) Bluetooth pairing cannot be made. • Make sure you have entered the same PIN code to both the unit and Bluetooth device. • Delete pairing information from both the unit and the Bluetooth device, then perform pairing again. ( 16) Echo or noise is heard during a phone conversation. • Adjust the microphone unit’s position. ( 16) • Check the [ECHO CANCEL] setting.
REFERENCES About iPod/iPhone Made for - iPod touch (2nd, 3rd, 4th, and 5th generation) - iPod classic - iPod nano (3rd, 4th, 5th, 6th, and 7th generation) - iPhone 3G, 3GS, 4, 4S, 5, 5S, 5C, 6, 6 Plus • You cannot operate iPod if “KENWOOD” or “ ” is displayed on iPod. • Depending on the version of the operating system of the iPod/iPhone, some functions may not operate on this unit. Maintenance Cleaning the unit Wipe off dirt on the faceplate with a dry silicone or soft cloth.
REFERENCES • Compatible remote device for NFC function: Remote devices with a NFC function (OS: Android™ 2.3.3 or later, excluding Android 3.x). If the OS version of your remote device is older than Android 4.1.x, download and start the “NFC Easy Connect” application. (“NFC Easy Connect” is a free application available at Google Play.) About HD Radio™ Technology • Adjacent to traditional main stations are HD2/HD3 Channels, providing new original programming on the FM dial.
SPECIFICATIONS / / : 87.9 MHz — 107.9 MHz (200 kHz space) : 87.5 MHz — 108.0 MHz (50 kHz space) USB Standard USB 1.1, USB 2.0 Full Speed File System FAT12/ 16/ 32 Maximum Supply Current DC 5 V Frequency Response (±1 dB) 20 Hz — 20 kHz Usable Sensitivity (S/N = 26 dB) 8.2 dBf (0.71 μV/75 Ω) Signal-to-Noise Ratio (1 kHz) 105 dB Quieting Sensitivity 17.2 dBf (2.
INSTALLATION / CONNECTION SPECIFICATIONS Warning 50 W × 4 Full Bandwidth Power 22 W × 4 (at less than 1 % THD) Speaker Impedance 4Ω—8Ω Tone Action Band 1: Band 2: Band 3: Band 4: Band 5: Band 6: Band 7: Band 8: Band 9: Band 10: Band 11: Band 12: Band 13: Audio Maximum Output Power • The unit can only be used with a 12 V DC power supply, negative ground. • Disconnect the battery’s negative terminal before wiring and mounting.
Part list for installation Installing the unit (in-dash mounting) (A) Faceplate Do the required wiring. ( 33, 34) (B) Trim plate Hook on the top side Orientate the trim plate as illustrated before fitting. Dashboard of your car (C) Mounting sleeve Bend the appropriate tabs to hold the mounting sleeve firmly in place. (D) Wiring harness When installing without the mounting sleeve 1 Remove the mounting sleeve and trim plate from the unit.
Wiring connection (for ) IMPORTANT : We recommend installing the unit with a commercially available custom wiring harness specific for your car and leave this job to professionals for your safety. Consult your car audio dealer. When connecting to an external amplifier, connect its ground wire to the car’s chassis to avoid damaging the unit.
Wiring connection (for / / ) IMPORTANT : We recommend installing the unit with a commercially available custom wiring harness specific for your car and leave this job to professionals for your safety. Consult your car audio dealer. Fuse (10 A) (For ) To the remote control, KCA-RC55MR (optional accessory) When connecting to an external amplifier, connect its ground wire to the car’s chassis to avoid damaging the unit.
• HD Radio Technology manufactured under license from iBiquity Digital Corporation. U.S. and Foreign Patents. HD Radio™ and the HD, HD Radio, and “Arc” logos are proprietary trademarks of iBiquity Digital Corp. • “Made for iPod,” and “Made for iPhone” mean that an electronic accessory has been designed to connect specifically to iPod, or iPhone, respectively, and has been certified by the developer to meet Apple performance standards.
