KNA-DV2600 DVD NAVIGATION SYSTEM INSTRUCTION MANUAL © B64-2784-00/00 (C) KNA-2600̲r3.2̲English.Indd 1 03.12.
Contents Safety precautions 3 Replacing Map Discs 4 Inserting the Map Disc ............................................... 4 Removing the Map Disc ............................................. 4 Starting Up Navigation System 5 Basic Operations 6 Marks and Controls on Current Position Map screen ............................................................... 6 Changing map scales ..................................................................6 Change of Map Orientation............................
Safety precautions Warning Messages Before Use For safe usage please observe the following !!! Start the car engine before use READ THIS MANUAL FIRST Read this manual carefully before starting to operate the Kenwood Car Navigation System and follow the manual's instructions. Kenwood are not liable for problems or accidents resulting from failure to observe the instructions in this manual.
Replacing Map Discs Inserting the Map Disc 1 Press the right side of the button marked DVD to open the cover. Press here! 2 Insert a map disc with the label side upward and close the cover. • No DVD Video disc can be played back by this unit. Removing the Map Disc 1 Press the right side of the button marked DVD to open the cover. Press here! 2 Press the eject button. 3 Remove the map disc and close the cover. 4 | English KNA-2600̲r3.0̲English.Indd 4 03.12.
Starting Up Navigation System Start up the navigation system and display the map of the area around your vehicle. 1 Start the engine. The CAUTION screen is displayed on the screen. 2 Read CAUTION carefully, and select . The current position is displayed on the screen. English | KNA-2600̲r3.0̲English.Indd 5 5 03.12.
Basic Operations Marks and Controls on Current Position Map screen 1 Vehicle marker Shows both its current position and the direction of the vehicle. 2 Map Orientation control Indicates the direction of "North". It also switches Map Orientation. (see page 7) 3 GPS (Global Positioning System) marker Shows the status of the signal from the GPS satellite. When this marker appears, the GPS satellite signal is being received and used to calculate the position of your vehicle.
Change of Map Orientation You can change orientations of the map displayed. North-up display Regardless of the vehicle’s direction of traveling, map is always shown with north upward. Heading-up display (This indicates north) Map is always shown with the vehicle’s direction of traveling upward. • Even when the heading-up display is on, maps and all the route maps called up on the screen for setting destinations are shown in north-up display.
Basic Operations Showing marks of the facilities Facility marks can be displayed on the map. ■ When showing marks for only one category 1 2 Select . Select the facilities to be displayed. Marks for the selected facilities will be displayed. If the desired category is not displayed, select . 3 Select . Marks for the selected facilities will be displayed. If mistakes are made, select one mark. to cancel one mark by • Facilities whose information is not included in the map disc are not displayed.
■ When canceling display of marks for facilities 1 2 Select . Select . ■ When searching for Surrounding facilities Names of facilities located near the current position direction from can be displayed. 1 2 Select or cursor , or the slant distance and . Select . List of selected facilities will be displayed. 3 Select names of facilities to be displayed. Maps featuring selected facilities will appear and names of facilities and the slant distance from the current position will be displayed.
Basic Operations ■ When displaying Lists in consideration of routes When destination(s) are set up, lists with distances, directions combined with routes can be shown. In this case, distances are displayed with the roads and distances and the displayed marks show which side their facilities are located. 1 Select . When the list in consideration of routes is shown, the operation indicator lamp turns green.
Marks and Controls on Scrolling Map screen Touch the screen when the current map is displayed, so that the Scrolling Map screen appears. 1 Cursor Indicates the position of the operation target. 2 button Restores the Current Position Map screen. 3 button Sets the cursor position for the destination. (see page 25) 4 button Registers the cursor location to the memory point.
Basic Operations Operation of MENU screen 1 Select . MENU screen will appear. The following operations can be conducted from the MENU screen.
Adjust the volume of voice guidance ■ When adjusting the volume The navigation volume is adjustable. 1 2 Select on the MENU screen. Select each button for the volume adjustment. The button turns green when selected. • Select to turn OFF the voice guidance. If one of the volume buttons is selected when the voice guidance is OFF, the voice guidance turns ON.
Basic Operations ■ Set the sound in other modes It is possible to choose whether the voice guidance is turned ON or OFF when switched to other modes. 1 2 3 Select Select on the MENU screen. . Select . When turned ON, the operation indicator lamp turns green. • It is also possible to switch by using the operation showed in (see page 48). • When you approach to a guide point while listening to another sound source, the voice guidance of the Navigation System starts automatically.
Switching to the twin-screen display When maps are displayed, the following is possible by splitting the screen into two vertically. Example: Display using different scales between the right and left frames, the heading-up display and the North-up display, ON and OFF display of facilities. ■ When switching to the twin-screen display 1 2 Select on the MENU screen. Select . Two maps are displayed on the screen. The selected switch turns green.
Basic Operations ■ When switching to the single-screen display 1 2 Select Select on the MENU screen. . • When switching to the twin-screen display again, the maps with the scale from the previous twin-screen display will appear. 16 | English KNA-2600̲r3.0̲English.Indd 16 03.12.
Calling up maps When setting and additions of destinations, registration of the home, memory points and specially memory points are performed, various ways can be used to call up maps and display them. As for the procedure to select the way to call up maps, please refer to the concerned pages for each item. Buttons — Items Functions The order of the syllabary Entering facility names enables maps to show surroundings of the facilities. The maps of the area can be displayed by entering the addresses.
Calling up maps Calling up according to the syllabary It is possible to enter a facility name that you only know partly using syllabary and narrow the number of candidates down in terms of the category, the area and names of cities and towns. 1 2 3 Select 4 Select . Then, the screen of the facility list searched by the entered characters will be displayed. 5 Select the name of the facilities in the list. The map will appear. Select on the MENU screen. .
When narrowing down according to the area 1 2 Select 3 Select the name of cities, prefectures or wards in the list. 4 Select the name of the facilities in the list. on the facility list screen. Select the name of city where the facility exists. • Select in the step 2, and the facility list screen is restored. • Select in the step 3, and the screen for the designated facility lists in terms of cities will be displayed. • Select , the character entry screen will be restored.
Calling up maps When narrowing down according to the categories of facilities 1 2 Select 3 Select the name of the facilities in the list. on the facility list screen. Select the category of facilities to be displayed. • Select in the step 2, and the facility list screen (the previous page 3) will be restored. • Select , the character entry screen will be restored. • Select , and the area to be displayed on the facility list screen can be designated.
Calling up maps in terms of facilities When the facility name is known, the map can be called up by selecting from the facility category. 1 2 Select 3 Select the category of facilities to be displayed. Other categories will be displayed by selecting 4 Select the name of the city where the facility exists. 5 Select the name of the facility to be displayed. The map will appear. Select on the MENU screen. . .
Calling up maps Calling up maps in terms of telephone numbers 1 2 Select 3 Enter numerals one by one. 4 Select . The map searched in terms of the entered telephone number will appear. Select on the MENU screen. . When multiple places with the identical telephone number exist, the screen to select the specific facility name will appear. 5 Select the name of the facility to be displayed. The map searched using the entered telephone number will appear.
Calling up maps in terms of addresses 1 2 Select 3 Select place names to be displayed in the order of provinces, cities, prefectures, wards and highways. The map will appear. Select on the MENU screen. . English | KNA-2600̲r3.0̲English.Indd 23 23 03.12.
Calling up maps Calling up maps in terms of postal codes 1 2 Select 3 4 Enter numerals one by one. Select on the MENU screen. . Select . The maps that have been searched in terms of the postal code will appear. • Enter 6-digit postal codes. • When entering wrong numerals, select , and they are deleted one by one. • As for the displayed maps, refer to (see page 17). 24 | English KNA-2600̲r3.0̲English.Indd 24 03.12.
Setting routes and route navigation Set destinations and conduct route searches Set destinations and search routes Set destinations from the screen for setting destinations. 1 Place the cursor at the point for the destination, and select . (see page 17) is convenient to use. 2 Select . Destinations will set at the points of the cursor mark and route searching will begin.
Setting routes and route navigation Displaying whole route Once route searches have been completed, the screen for the whole route will appear. Regarding display The display screen will show the whole route to the final destination. 1 Indication of distances of express ways The distances of all the toll roads to pass through to the destination are indicated. 2 Indication of distances The distances to the destinations will be indicated.
■ When displaying route information It will include road types, distances or expected passing times. 1 Select on the Whole Route screen. Route information is displayed separately in terms of destinations or road types. Each of such separated route information has the road name and its distance. 2 Select . The respective maps for the set points will appear. • The current position of the vehicle will be indicated on the route information screen if it is on the route.
Setting routes and route navigation ■ When displaying 5 routes to compare them It will include road types, distances or expected passing times. 1 2 Select on the Whole Route screen. The 5 routes will be displayed with 5 different colors. 3 Select a route. The screen for the whole route of the selected map will appear. Select . The list of distances of the 5 routes and time periods required for driving each route. • In the following cases, it is impossible to display the 5 routes at the same time.
Changing routes It is possible to change the routes that have been searched. Select whole route display screen, and the route-change screen will appear.
Setting routes and route navigation 5 Select 6 Select . Route search will be performed again. of road sections. To set more destinations, select 1 to 4. and repeat steps • It is possible to set to a maximum of 5 destinations. When 5 destinations have already been set, delete unnecessary destinations. (see page 32) • In the case the roads to pass through are designated, the following message may appear. If you wish to cancel the setting of roads to pass through, select , and if not, select .
Sorting destinations It is possible to sort the multiple set destinations that have been set and search them again. 1 2 3 Select on the MENU screen or the Whole Route screen. Select of destinations and passing destinations on the screen for changing routes. Touch destination names in the order of visiting destinations. The new order will be displayed to the right of the touched destination names. When making a mistake, select , and the order of the selected destination names will be canceled.
Setting routes and route navigation Clearing destinations It is possible to clear one of the multiple set destinations. It is also possible to clear all the destinations at the same time. 1 2 Select on the MENU screen or the Whole Route screen. 3 Select the destination names. Select when you wish to clear all the destinations. 4 Select . If only one destination has been set when all the destinations are cleared, the screen indicating the current point will appear. 5 Select .
Setting passing roads It is possible to set a maximum of 2 passing roads (passing points) on the route. 1 2 3 4 Select on the MENU screen or the Whole Route screen. 5 Select to select passing roads. When designating the displayed roads, select 6 7 Select . The passing roads will be designated with marks ◆. 8 Select . Route searches will be conducted again. Select of passing points (designation of passing roads) on the screen for changing routes.
Setting routes and route navigation ■ When correcting the passing roads 1 2 Select on the MENU screen or the Whole Route screen. 3 Select a button of passing points to correct. The map will appear. 4 Scroll the map to the position for designating passing roads. 5 6 7 Select Select of passing points (designation of passing roads) on the screen for changing routes. When only one point has been set, the screen 3 will appear. . Select to select passing roads.
8 Select . Route searches will be conducted again. • When the maps shown in step 6 have little information, no roads may be selected even if is selected. ■ When canceling designation of passing roads 1 2 Select on the MENU screen or the Whole Route screen. 3 Select a button of passing positions to cancel. To cancel designation of all the passing roads, select . 4 Select If restored. 5 Select . Route searches will be conducted again. Select of passing roads (designation of passing roads).
Setting routes and route navigation Changing search conditions It is possible to change search conditions and search again. 1 2 3 Select on the MENU screen or the Whole Route screen. 4 Select . Route searches will be conducted again. Select on the screen for changing routes. Select search conditions (route names) for each road section. 36 | English KNA-2600̲r3.0̲English.Indd 36 03.12.
Route Guidance Initiate route guidance Route guidance will be performed by screen display and voice (Route guidance). 1 Select on the Whole Route screen. Route guidance will start. When selecting after the whole route map is displayed or when no operation has been conducted for more than 3 seconds, automatic destination guidance will begin. ■ When cancel or resume route guidance 1 Select on the MENU screen. • Even if destination guide is suspended, destinations will not be cleared.
Setting routes and route navigation Open road route guidance When destinations are set, routes to them will be indicated. • Guidance is performed only when the current position is placed on the blue indication. There are 2 kinds of route indicating colors as follows: - Blue : Normal indication - Light blue : Narrow street indication 1 Route indication ■ Narrow street indication Even narrow streets can be searched around the current position and the destination.
■ Information on intersections When the vehicle is coming closer to an intersection with a guide point, information on the intersection will be provided with on the current position screen where route guidance is going on (when the current position is on the route). When the vehicle is coming closer to a forked intersection (within about 300m), the screen for information on intersections will appear automatically. 1 Lane indication Lanes of passing or branched intersections will be indicated.
Setting routes and route navigation ■ In order to switch indications of remaining distances It is possible to switch such remaining distances on the Current Position Map screen (only when the current position is on the route) while destinations are guided when 2 or more destinations are set. 1 Select . The destinations will be switched every time it is selected. • Values of distances to destinations will vary depending on situations.
Route guidance on expressway When driving on an express way and the vehicle is approaching a branch point (interchange exit (IC), junction (JCT)), the screen for expressway branch point information will appear automatically. 1 Distance indication Distance to branch points will be indicated. 2 Indication of branch point names Names of IC exits or heading cities and towns from JCT will be indicated. 3 Canceling guidance Close the screen for expressway branch point information.
Setting routes and route navigation Voice route guidance When the vehicle is approaching an intersection during destination guidance while destinations are guided, a branch point or a destination, voice guidance informs you of the remaining distance and which direction to turn. 1 Select . Voice guidance will be given according to the distance to the branch point. An example of voice guidance while destinations are guided. • Before a branched intersection, - About 300 meter ahead, on the right.
Scrolling the map along the route The map can be automatically moved to the starting point or to the destinations along the route. (On-route scroll) 1 2 Select on the MENU screen. Select the control for scrolling. : The map will be scrolled to the next destination. : The map of the next destination will be displayed. : The map will be to the previous destination scrolled. : The map for the previous destination will be displayed. : Movement of maps will be suspended. : On-scroll will be terminated.
Setting routes and route navigation ■ When scrolling to the next facility 1 2 When selecting 3 Select the facilities you wish to indicate on the onroute scrolling screen. It is only one facility that can be set. Select . . Select , and marks other than those for facilities that are displayed with the touch switch can be displayed. When a mistake is made, select 4 Select . .
Demonstration (Demo) After completion of route searches, it is possible to view demonstration of destination guidance before it is started. 1 2 Keep selecting on the Whole Route map display for more than 3 seconds. If or is selected during the demonstration, it is terminated and the screen for the current position will be restored. Driving during the demonstration will also cause it to terminated and destination guidance will be started.
Setting routes and route navigation Another route search When you wish to change the searched routes, or the current position is not located on the route (deviated from the route), route searches can be retried. When the current position is indicated on the screen while the destination is guided (including the case it is deviated from the route), route searches can be retried. Routes to be searched again will vary by selecting the 7 items shown below.
When the vehicle is deviated from the route When the vehicle is deviated from the route, another search (peripheral search or the search for all the route) can be conducted automatically. The routes that can be searched again vary according to the situation where the vehicle is deviated. • Searching the periphery: The routes to return to the original route will be searched.
Setting routes and route navigation Setting navigation Various kinds of settings for navigation will be set. 1 2 Select 3 Select on the MENU screen. Select the items to be set. The selected control will turn green. . • The items that can be set are as follows: Functions Items Conducted When deviated from the route, another search will be conducted automatically. Not conducted When deviated from the route, another search will not be conducted automatically.
■ When setting the average vehicle speed The average vehicle speed can be set for the criteria to calculate the times and the time periods shown below. - Estimated arrival times on the screen for displaying all the routes. - Expected passing times included in the route information - Required time for indicating 5 routes at the same time. - Estimated arrival times at the destinations on the Current Position Map screen. 1 Select 2 Select road. or 3 Select . of indication of estimated arrival times.
Setting routes and route navigation ■ When correcting the current position When the position or orientation of the vehicle is misaligned, or tires are changed, correction should be conducted. 1 Select . The screen for correcting navigation will be indicated. 2 Select 3 Select and scroll the map to the actual current position. 4 5 Select 6 . . Set the direction. Select when turning the direction counterclockwise, and select when clockwise. Select . 50 | English KNA-2600̲r3.0̲English.
■ When correcting settings of distances manually 1 Select . 2 Select . 3 Select or . : When the vehicle marker moves faster than the actual vehicle. : When the vehicle marker moves slower than the actual vehicle. 4 Select . • When you purchased, this has been set in the Automatic Correction mode. The Automatic Correction works while driving.
Setting routes and route navigation History of destinations The destinations that your vehicle has reached are automatically memorized and can be called up when setting destinations (Up to 20 destinations). When the number exceeds 20, they will be deleted automatically in the order of occurrence. Unnecessary destinations can be deleted manually. ■ When clearing history of destinations 1 2 Select 3 Select the place names. Select when clearing all the history of destinations. 4 Select Select restored.
Indicating information on the map disc Information such as a database stored in the Map DVD-ROM can be viewed. The screen below is an example of displays and the contents will vary depending on the production times of the Map DVD-ROM and types. 1 Select on the MENU screen. • Information on roads, place names, and facilities can be changed after production of the Map DVD-ROM, it can be different from the actual situation.
Registration of points Points to be memorized on the map can be registered. The registered points can be corrected or cleared. Registering your home Your home address can be registered at one place on the map. Once your home is registered, route searches can be started in one operation from the screen for setting destinations. Registering your home 1 2 Select 3 Select a button how to call up maps. Refer to (see page 17). 4 Select . Your home will be indicated at the position mark .
Registering memory points Up to 100 memory points (landmarks) can be registered. 1 2 Select 3 Select a button how to call up maps. Refer to (see page 17). 4 Select 5 Select the mark to use. The memory point will be indicated at the position of Kinds of marks for memory points can be changed by selecting , . on the MENU screen. Select of memory points. . • When a maximum of 100 memory points have already been registered, you can clear unnecessary items to register new ones.
Registration of points ■ When registering displayed places Memory points can be registered on the map currently displayed. 1 Select . The current position on the Current Position Map screen or the specified position by the cursor on the Scrolling Map screen will be registered as a memory point, and mark will be indicated. 56 | English KNA-2600̲r3.0̲English.Indd 56 03.12.
Correcting memory points 1 2 3 Select Select on the MENU screen. of memory points. Select the point to be corrected. The screen with the corrected point will appear. • The memory points in the list can be sorted in the 2 ways: in the order of the registered memory points and according to mark types. - Select , and the items will be sorted according to mark types. - Select , and the items can be sorted in the order of registered memory points.
Registration of points ■ When inputting names 1 Select 2 Select , , , and switch the entry screens. As for entering chinese-character, please refer to below. 3 Select 4 Select one character by one character to input names. When wrong characters are input, select and the characters will be cleared one by one. 5 Select of name. or . . • The number of characters that is possible to input is up to 12 characters. 58 | English KNA-2600̲r3.0̲English.Indd 58 03.12.
■ When inputting chinese character using pinyin 1 Select first sound. If the first sound inputted is enough to confirm one of the chinese character candidates, the screen 3 will appear. 2 Select second sound. 3 Select the chinese character to input on the displayed screen (chinese character list). When chinese character candidates are so many that they spread over multiple pages, select ( ) to switch the pages and search the target letters.
Registration of points ■ When indicating names on the map 1 Select of name. The selected button will turn green. ■ When correcting positions 1 2 3 Select of position. Select and move the map to the position where the memory point should be corrected. Select . Select of telephone unmber. ■ To input telephone numbers 1 2 3 Select the numerals one by one to input. Input area codes first. In the case of an input errors, select , and numbers will be clearedone by one. Select .
Clearing memory points 1 2 3 Select Select Select on the MENU screen. of the memory points. when you wish to clear all the memory. Select the point to delete. 4 Select If restored. . is selected, the original screen will be • There is no way to restore the cleared memory points. Conduct operations careful enough not to make mistakes. English | KNA-2600̲r3.0̲English.Indd 61 61 03.12.
Registration of points Registering of special memory points Up to 5 special memory points can be registered on the map. If such special memory points are registered, they can be called up by one-touch unlike the other Memory points when the maps are called. When setting destinations, route searches can be started by one-touch on the screen for setting destinations. 1 2 Select 3 Select the numbers of memory points. 4 Select when the number of the special memory points has already been registered.
Correcting special memory points 1 2 Select 3 Select on the right of items to be corrected and inputted. The way to correct and input is the same as the way to correct and input memory points. (see page 55) of special memory points. Select the memory point to correct and input. • Special memory points will be indicated using the dedicated marks (with numbr) and the marks cannot be changed. Clearing special memory points 1 2 3 Select of special memory points.
AVN-2675's Monitor Unit Basic Operations VSVD1 WD F U L L VOL S P NORMA L WIDE MODE A V NORMA L V.SEL down up Turning ON/OFF the power Adjusting the Volume Power Turning on the power: Press the [V.SEL] button. Turning off the power (Stand by mode): Press the [V.SEL] button for at least 1 second. Increasing Volume: Press the [up] button. Decreasing Volume: Press the [down] button. Switching the Picture Switching the Video Screen Mode Press the [V.SEL] button.
Picture Quality Adjusting Dimmer Sensor SCREEN Adjusting the Picture Quality • You cannot operate when the navigation picture is displayed. 1 Displaying the Screen Control screen Press the [SCREEN] button. 2 Setting Touch the [2] or [3] button. Switching the Speaker Mode Press the [WIDE MODE] button for at least 1 second.
AVN-2675's Monitor Unit Setup Menu screen SCREEN Select the Setup Menu screen Press the [SCREEN] button for at least 1 second. Setup Menu screen is displayed. SCREEN System Setup screen-1 ■ Setting the Navigation Mode
■ Setting the AV IN-2 Mode Touch Setting [7AV-IN1] It becomes the video mode setting. Operate the V.SEL button when the image from the device connected to terminal is shown on the monitor. [7OFF] It becomes the OFF mode setting.Use this setting when there’s nothing connected to the terminal.
AVN-2675's Monitor Unit Setup Menu screen Touch Panel Adjustment On-screen Control Mode The touch panel can be adjusted if the position touched and the operation performed do not match. When the current setting information is displayed on the screen, touching a dotted line will enable operation of each of the following items: 1 Accurately touch the mark at the lower left. 2 Accurately touch the mark at the upper right.
• You cannot operate when the navigation picture is displayed. ■ Switching the Speaker Mode [SP] Press the B part. Each time the B part is touched the built-in speaker mode switches as follows: Display "NORMAL" "NAV" "VIDEO1" "VIDEO2" "OFF" Setting Sound with monitor picture Sound with navigation picture Sound with video 1 picture Sound with video 2 picture Built-in speaker is turned off ■ Setting the AV Output Mode [AV] Touch the E part.
General Information Accuracy of the Vehicle’s Position How the Vehicle’s Position is detected Area in which GPS signals cannot be received Detecting the vehicle’s position through the GPS Because the radiowave signals from the GPS satellites travel primarily by line of sight, the navigation system might not be able to receive the signals in the areas described below. (If the GPS mark does not appear on the map screen, it means that the GPS radiowave signals are not being properly received.
Troubleshooting Confirm whether any problem is due to a minor operational error or a malfunction. Check the table below before contacting your local dealer for any repair service. ■ Navigation System (KNA-DV2600) ■ AVN-2675's Monitor Unit ? The power does not come on. ✔ The fuse might be blown. ☞ Check the fuse. Replace it if it is blown. ? ? The map does not scroll even when the vehicle is moving. ✔ The screen shown might not be the Current Position screen.
Specifications Specifications subject to change without notice. ■ Navigation System (KNA-DV2600) ■ AVN-2675's Monitor Unit Navigation Section Monitor Unit Antenna : Micro-strip patched antenna Receiver channel : Digital 8-channels parallel Receiving frequency : 1575.42 MHz (C/A code ) Receiving sensitivity : Less than -130 dBm Positioning method : Hybrid (GPS + Wheel Pulse + Gyro Sensor) General Operating voltage (11 to 16 V) : 14.4 V DC Current consumption (13.2 V) : Less than 1.
