CONGRATULATIONS! Box contents Your Here2Anywhere™ Portable SIRIUS® Satellite Tuner lets you enjoy SIRIUS Satellite’s digital entertainment streams anywhere you’ve installed one of our KPA-H2H Home Docking Kits or KPA-H2C Car Docking Kits (available separately). Use this manual to familiarize yourself with all of Here 2Anywhere’s features and capabilities.
Warning Take the following precautions to prevent fire and avoid personal injury: • When replacing a fuse, use only a new one with the proper rating. Using a fuse with the wrong rating may cause the unit to malfunction. instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made.
Installation in a vehicle with the KPA-H2C kit (available separately) Installation in a vehicle (continued) Note: Do not put Here2Anywhere in the docking station until you have completed the installation. 1. Determine where you want to mount 2. You can bend the leaves on the base to conform to curved mounting surfaces. Here2Anywhere. • Do not install Here2Anywhere where it may obstruct your view through the windshield or your view of your vehicle’s indicator displays.
Installation in a vehicle: Mounting the antenna 1. Temporarily plug the antenna into the “1-Sat/Terr (Main)” connector on the back of the cradle until it is firmly seated, as shown. 8 Installation in a vehicle: Routing the cable Note: If you’re using the Kenwood CX-SR10 SIRIUS antenna, you’ll need to remove the plastic housings from the antenna connectors—we recommend labeling the wires with their respective colors. (See pg. 9, figure 16 of the CX-SR10 Installation Manual for details).
Installation in a home with the KPA-H2H kit (available separately) Installation in a home (continued) Note: Do not put Here2Anywhere in the docking station until you have completed the installation. 1. Using the provided screw, 2A. Plug the audio 2B. Plug the audio assemble the docking station cable’s mini cable’s white cradle to the base. connector into the (L ch,) and red back of the (R ch.) connectors cradle, as shown. into your audio system. 3.
Front-panel controls and features Up/Down/Left/Right Arrow Buttons: Navigates through display screens Display: Shows information about streams, categories, artists, songs and setup information Remote Control Receiver: Receives signals from the included wireless remote control POWER Button: Turns Here 2 Anywhere on and off; enters & exits the Setup Mode, and exits the Stream, Category, Song & Artist List modes SELECT Button: Makes selections of items highlighted on the display Preset Number Buttons: Sets and
Activating your SIRIUS subscription Before you can listen to Here2Anywhere, you must subscribe to SIRIUS Satellite’s service. 1. Make sure that Here 2 Anywhere is properly connected and that its antenna is oriented to receive the SIRIUS satellite signal (see Installation sections for details). 2. Press the power button to turn Here2Anywhere on. After displaying the Kenwood and SIRIUS logos, the display will read “Acquiring Signal”.
4. If you decide not to select another stream, press the POWER button to exit the mode. The display will revert to the Normal Operation screen for the active stream. • You can switch to the previously-selected stream by holding the SELECT button for at least 1 second. Holding the SELECT button for 1 second again switches back to the original stream.
• After you make your selection, the display will revert to the Normal Operation screen 2. When the desired preset bank is displayed, use the “1” – “6” buttons to tune the desired preset stream Note: In the Stream List, Artist List and Song List modes, if you don’t want to make a selection, press the POWER button to exit the mode and return to the Normal Operation screen for the active stream.
Saving/recalling music information Adjusting the display brightness You can store the name of the currently-playing song and artist (and composer, if the data is available) into memory for recall later. 1. Use the up & down arrow buttons to select the desired brightness level (high/medium/low) Hold the DISPLAY button down for over 1 second to enter the Display Brightness mode (right): Saving music information Press the MEM button to save the data.
1. While in the Setup Mode, press the left or right arrow button until the Channel Skip screen appears (right): 2. Press the up or down arrow button. The Lock Code screen appears (top, right): 2. Use the up & down arrow buttons to highlight the stream you want. (The highlighted stream will automatically play.) 3. Using the preset 1 – 6 buttons, enter the factory default code “1 1 1 1”. The screen’s second line will change from “_ _ _ _” to “* * * *”. 3.
8. Press the MEMORY button. The display will change to “New Code Confirmed” • “High” is 0dB, “Medium” is –3dB and “Low” is –6dB. • If you entered the code incorrectly, “Code Error” will be displayed, and the Enter New Lock Code screen reappears. Repeat Steps 5 – 8. Note: To avoid distortion with some cassette car stereos, you may have to lower the output level when using the cassette adapter. Startup Mode Antenna Signal You can select which screen is displayed when you turn Here2Anywhere’s power on.
Troubleshooting guide Problem Troubleshooting Guide (continued) Possible Cause Solution Power supply/cigarette lighter adapter not properly connected Blown fuse in cigarette lighter adapter No sound Audio cable/cassette adapter not Make sure cable/adapter is properly connected properly connected Display reads “Antenna Error” Signal is weak or can’t be found The antenna is not connected The antenna or cable is faulty Verify antenna connections Replace antenna 26 Stream entered is invalid Solution