CONGRATULATIONS! Box contents Your Here2Anywhere™ Portable SIRIUS® Satellite Tuner lets you enjoy SIRIUS Satellite’s digital entertainment streams anywhere you’ve installed one of our KPA-H2H Home Docking Kits or KPA-H2C/KPA-H2CFM Car Docking Kits (available separately). Use this manual to familiarize yourself with all of Here 2Anywhere’s features and capabilities.
Warning Take the following precautions to prevent fire and avoid personal injury: • When replacing a fuse, use only a new one with the proper rating. Using a fuse with the wrong rating may cause the unit to malfunction. instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made.
Installation in a vehicle with the KPA-H2C kit (available separately) Installation in a vehicle (continued) Note: Do not put Here2Anywhere in the docking station until you have completed the installation. 1. Determine where you want to mount 2. You can bend the leaves on the base to 4. Plug the cigarette lighter adapter Here2Anywhere. into the back of the cradle, as shown. conform to curved mounting surfaces.
Installation in a vehicle (continued) Note: If you’re using the Kenwood CX-SR10 SIRIUS antenna, you’ll need to remove the plastic housings from the antenna connectors before connecting it to the cradle—we recommend labeling the wires with their respective colors. (See pg. 9, figure 16 of the CX-SR10 Installation Manual for details).
Mounting the antenna (continued) Installation in a home with the KPA-H2H kit (available separately) Installation in a home with the KPA-H2H kit (continued) Finding a location for the antenna 7. Route the cable from the lowest point of the rear window into the trunk. Take advantage of any existing cable channels or wiring conduits. • For SUVs, minivans & 5-door vehicles, bring the cable into the vehicle under the rubber molding for the tailgate, and continue under the interior trim. 8.
Finding a location for the antenna (continued) The second best antenna location is on an outside wall • Use an appropriate wall, depending on where you live (refer to the map on page 13). The location of the “X” on the map must be visible to the antenna • Mount the antenna facing as close to straight up as possible (below, left) • To minimize interference caused by roof extensions, mount the antenna as low on the wall as possible while avoiding other obstructions (below, right).
Front-panel controls and features Up/Down/Left/Right Arrow Buttons: Navigates through display screens Display: Shows information about streams, categories, artists, songs and setup information Remote Control Receiver: Receives signals from the included wireless remote control POWER Button: Turns Here 2 Anywhere on and off; enters & exits the Setup Mode, and exits the Stream, Category, Song & Artist List modes SELECT Button: Makes selections of items highlighted on the display Preset Number Buttons: Sets and
Activating your SIRIUS subscription Before you can listen to Here2Anywhere, you must subscribe to SIRIUS Satellite’s service. 1. Make sure that Here 2 Anywhere is properly connected and that its antenna is oriented to receive the SIRIUS satellite signal (see Installation sections for details). 2. Place Here2Anywhere in the docking station by sliding the unit all the way into the cradle so that the connector at the rear of the unit makes proper contact in the cradle. 3.
4. If you decide not to select another stream, press the POWER button on the front panel to exit the mode. The display will revert to the Normal Operation screen for the active stream. • You can switch to the previously-selected stream by holding the SELECT button for at least 1 second. Holding the SELECT button for 1 second again switches back to the original stream.
• After you make your selection, the display will revert to the Normal Operation screen 2. When the desired preset bank is displayed, use the “1” – “6” buttons to tune the desired preset stream Note: In the Stream List, Artist List and Song List modes, if you don’t want to make a selection, press the POWER button on the front panel to exit the mode and return to the Normal Operation screen for the active stream.
Saving/recalling music information the list of saved songs until the one you want is highlighted. Saving music information You can store the name of the currently-playing song and artist (and composer, if the data is available) into memory for recall later. Press the MEM button to save the data. The screen will display the following message (above): • If the song has already been stored in memory, the display will read “Already Stored”. • You can save data for up to 24 songs.
Press the DISPLAY button to cycle the display between the two modes. Clock Setup Adjusting the display brightness Here2Anywhere has an automatic clock that receives its time signal as part of the SIRIUS satellite stream. Hold the DISPLAY button down for over 1 second to enter the Display Brightness mode (right): 1.
Timer Functions 7. Use the up and down arrow buttons to move through the streams until the one you want is highlighted. Here2Anywhere has three Timer functions. The Alarm turns Here2Anywhere on at a specified time and to a specified stream, Auto Shut-Off automatically turns it off at a specified time, and the Sleep Timer lets you listen to Here2Anywhere for a specified period of time before it automatically shuts off. 8. Press the SELECT button to save your setting. The Alarm Setup screen will reappear.
, 30 or 60 minutes). This is especially useful if your vehicle’s cigarette lighter remains powered after the ignition has been turned off. 1. While in the Setup Mode, press the left or right arrow button until the Auto Shutoff Setup screen appears (below). 2. Press the up or down arrow buttons until the display shows amount of time you want Here2Anywhere to stay on after the last time a button is pressed before it automatically shuts off.
To lock a stream, in Step 3 above, instead of momentarily pressing the SELECT button, hold the button for more than 1 second. A “–” and a padlock will be displayed next to the stream number. Lock Code Setup If you have locked any streams in the Channel Lock mode, you will need to enter a 4-digit lock code to unlock them. The factory default lock code is “1 1 1 1”. You can change the Lock Code to your own preference: 1.
Text Flow Type You can set how the scrolling text flows across Here2Anywhere’s screen. 1. While in the Setup Mode, press the left or right arrow button until the Text Flow Type screen appears (right): Text Flow Type Screen Output Level You can adjust Here2Anywhere’s output level so it matches other sources in your audio system. 1. While in the Setup Mode, press the left or right arrow button until the Output Level screen appears (right): 1.
Troubleshooting guide Problem Troubleshooting guide (continued) Possible Cause Solution Power supply/cigarette lighter adapter not properly connected Blown fuse in cigarette lighter adapter No sound Audio cable/cassette adapter not Make sure cable/adapter is properly connected properly connected Display reads “Antenna Error” Signal is weak or can’t be found Metallic window screen is interfering with reception Move antenna to window with a non-metallic screen The antenna is not connected The antenna
