KVR-A7OR KENwooD ETTGTISH FRArrgArs DEUTSCH AM-FM Stereo Receiver Instruction manual Ampli-Tuner AM.FM Stéréo Mode d'emploi MWIUKW Stereo Receiver Bedienungsanleitung PRINTED IN JAPAN 850.
BeÍore operation I For your records Record the serial number, found on the back oÍ the unit, in the spaces designated on the warranty card, and in the space provided below. Refer to the model and serial numbers whenever you call upon your dealer for information or service on this product. Model KVR-A7OR Serial Number Unpacking Unpack the unit carefully and make sure that all accessories are put aside so they will not be lost. Examine the unit for any possibility of shipping damage.
System connections s Do not make connections to 300 O and 75 0 antenna terminals simultaneously.
Speakers This unit has two pairs of speaker terminals, SPEAKERS A and SPEAKERS B. Connecting one speakor systom Connect speakers rated at 4 ohms or more to the SPEAKERS A terminals. Connecting two speaker systems To connect an additional pair of speakers, use the B terminals. ln this case. each speaker must be rated at 8 ohms or more. Gonnection whh speaker cords 1 . Connect the leÍt speaker to the E SPEAKERS terminals and the right speaker to the El SPEAKERS terminals. 2.
AM antennas cable is somewhat more difficult to install at the point where AM loop antenna the cable enters the building. if coaxial cable is selected, Tune in your favorite AM station and position the loop antenna for best reception. ïry other stations and Íind the position that gives best overall reception. When this unit is mounted in a rack or placed on a shelf with insufficient space behind, remove the loop antenna and hang it from a wall in the direction which gives best reception.
Gontrols, indicators and connectors o neuore PowER switch By pressing this switch with the MAIN POWER switch set to ON, the power oÍ the unit and the power of the equipment connected to the SWITCHED AC outlet can be switched ON/OFF. When this switch is pressed, the function selected last or the last station to be received will be displayed. You can operate the switch from a distance with the RC-90 (remote control unit).
O uP/DowN (D TUNTNG buttons Auto tuning mode - When the UP or DOWN button is pressed, the frequency automatically increases or decreases until the next station of sufficient signal strength is reached. Manual tuning mode - Each time the UP or DOWN button is pressed, the tuned frequency increases or decreases in the following manner. FM 50 kHz steps - Each press alternates auto tuning and manual tuning modes.
@ Display window e @ @ @ O @ @ @ @ @ @ @ @ @ @ @ @ ln graphic equalizer mode, displays the equalizer level display and power level display. ln graphic equalizer mode, displays the channel in which the equalizer curve is stored. Flashes when storing equalizer curves in memory. Lights when the A LOUDNESS or B PRESENCE curve is selected. ln tuner mode, lights during auto tuning. ln tuner mode, lights duríng manual tuning. ln tuner mode, lights when a station is tuned in.
Operating instructions Listening to AM/FM broadcasts First set the MAIN POWER switch to ON, then the REMOTE POWER switch to ON. Press the TUNER button of the INPUT SELECTOR: "TUNER" and digital display are displayed in the display window. Next press the FM or AM button of the BAND SELECTOR. When FM is pressed, select also MONO or AUTO of the FM MODE buttons. Auto tuning 1. Press the AUTO/MANUAL button to set to "AUTO". 2.
Dubbing between two video recorders The program source selected by the INPUT SELECTOR (heard from the speakers) can be recorded in the audio track of the video tape. When dubbing Írom a program source other than VCR, set ting the G.E. switch to ON enables recording of the equalized sou nd. When dubbing from VCR, the SYNTHETIC STEREO switch and G.E. switch can be operated.
0perating procedure oÍ the remote control unit Battery Load the supplied Remote control unit operation range 2 AAA, R03 batteries as shown below. 1. Open the battery compartment lid. 2. Load the batteries, observing the polarities. When the operation indicator of the remote control unit does not light even when a button is pressed, the batteries may be exhausted. Replace with new batteries. KVR.
lD. munruc button The same function as the MUTING button @ on the main unit front panel. (D vOt-UltrtE controls The same function as the VOLUME controls @ on the main unit front panel. Buttons @ , (p , (p are used for remote control of the DP-840 (CD player), KX-74R (tape deck) and KD-74F/KD-64F (turntable) connected with synchro connec- to the main unit (in addition to connections using ordinary audio cables). For details, refer to the instructions provided with each unit.
ln case of difÍiculty lf your unit should not perform as expected, consult the table below to see if the problem can be corrected before seeking help from your dealer or service representative. Symptom No power, no sound. 1. Power cord not plugged in. 2. Poor connection at wall outlet. Power outlet inactive. No sound from left and right. Sound from left Remedy Cause or right, but not a lamp or other appliance (outlet may be controlled by a wall switch). 1. Speaker cords disconnected. 1.
SpeciÍications Section (tHF',661 Signal to Noise Ratio at 65 dBf MONO STEREO Power Output 45 watts per channel minimum RMS, both channel driven at 8 ohms from 20 Hz to 20,O00 Hz with no more than 0.008% total harmonic distoÉion Maximum Gontinuous Power Output (lECl Írom 63 Hz to 12,5OO Hz, O.7o/o THD at4 ohms .....70 W+70 W at8 ohms .....53 W+ 53 W Maximum Continuous Power Output (DlN) 1 kHz at4 ohms .....73 W at8 ohms .....55 W Total Harmonic Distortion l2O Hz - 2O,OOO Hz, 8 ohmsl .....0.
