FM/AM RECEIVER R-SE9T DP-SE9 X-SE9 CD PLAYER CASSETTE TAPE DECK INSTRUCTION MANUAL KENWOOD CORPORATION COMPACT DIGITAL AUDIO DT B60-3715-00 JA (T) AP WS AP 98/12 11 10 9 8 7 6 5 4 3 2 1 97/12 11 10 9 8 7 6 5
Before applying power power Caution : Read this page carefully toBefore ensureapplying safe operation. R-SE9T/DP-SE9/X-SE9 (En) Units are designed for operation as follows. Europe and U.K. ................................................. AC 230 V only U.S.A. and Canada ............................................ AC 120 V only For the United Kingdom Factory fitted moulded mains plug Basic section Preparation section 1.The mains plug contains a fuse.
Caution : Read the pages marked carefully to ensure safe operation. Before applying power 3 R-SE9T/DP-SE9/X-SE9 (En) Contents Preparation section Application section Before applying power ................................................. 2 Playback of CD ............................................................. 31 Safety precautions .............................................................. 2 IMPORTANT SAFEGUARDS ...............................................
Caution : Read this page carefully to ensure safe operation. Before applying power R-SE9T/DP-SE9/X-SE9 (En) IMPORTANT SAFEGUARDS Preparation section Please read all of the safety and operating instructions before operating this appliance. Adhere to all warnings on the appliance and in the instruction manual. Follow all the safety and operating instructions. These safety and operating instructions should be retained for future reference. 1.
Caution : Read this page carefully to ensure safe operation. Before applying power 5 R-SE9T/DP-SE9/X-SE9 (En) 20. Overloading – Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock. 21. Attachment – Do not use attachments not recommended by the appliance manufacturer as they may cause hazards. 22.
Before applying power R-SE9T/DP-SE9/X-SE9 (En) The High grade Micro Component Series Thank you for purchasing the High grade Micro component series. This system is available in various configuration according to your preferences. The system configuration is up to you, but as the following convenient system operations can be executed by connecting the various units to the system control, the respective units should be purchased as required.
Before applying power 7 R-SE9T/DP-SE9/X-SE9 (En) Special features 7 Amplifier unit that accomplishes high grade sound quality and low distortion ¶ New “TRAITRA” transistor The newly developed “TRAITRA” transistor with extremely superior temperature characteristics is used in this amplifier’s amplification circuit. Through the use of this transistor, distortion generated because of temperature change is kept to a minimum resulting in “pure” sound reproduction.
System Composition and Installation System connection R-SE9T/DP-SE9/X-SE9 (En) The High grade Micro component series permits various combinations according to the purchased components. As the installation differs according to the components you purchase, please install correctly under reference to the illustrations.
System connection System connection 9 R-SE9T/DP-SE9/X-SE9 (En) 1. Antenna connection Connect the antenna as shown in the figure. Do not plug the power cord into a wall AC outlet until the connection has been completed. 1 2 3 FM indoor antenna AM loop antenna The accessory antenna is for temporary indoor use only. For stable signal reception we recommend using an outdoor antenna. Remove the indoor antenna if you connect one outdoors. The supplied antenna is for indoor use.
System connection R-SE9T/DP-SE9/X-SE9 (En) 2. Connection of audio cord Malfunction of microcomputer If operation is not possible or erroneous display appears even though all connections have been made properly, reset the microcomputer referring to “In case of difficulty”. Here, connection of separately sold components also will be explained under consideration of system connection. Please install correctly according to the purchased components and connect the required cords.
System connection 11 R-SE9T/DP-SE9/X-SE9 (En) Caution regarding placement Caution for Connection When connections are to be made, make sure that the power plug is not plugged into a wall AC outlet. Connect the equipment as shown in the figures. To maintain proper ventilation, be sure to leave a space around the unit (from the largest outer dimensions including projections) equal to, or greater than, shown below.
System connection R-SE9T/DP-SE9/X-SE9 (En) 3. Connection of speakers Connect the speakers as shown in the figure. Do not plug the power cord into a wall AC outlet until the connection has been completed. 1 Cord preparation. Speaker (right) (6-16Ω) Speaker (left) (6-16Ω) Preparation section 2 Loosen. · ª ª · SPEAKERS ( 6 - 16 ) 3 Insert. R L Basic section 4 Secure. R-SE9T Connection of banana plugs 1 Secure.
System connection 13 R-SE9T/DP-SE9/X-SE9 (En) 4. Connection of system control cord Connect the system control cords and the power cords as shown in the figure.
Controls and indicators Controls and indicators R-SE9T/DP-SE9/X-SE9 (En) Main Unit TUNED indicator Stereo reception indicator AUTO indicator MUTE indicator MUTE AUTO ST. RDS display Sleep timer indicator N.B. indicator TUNED RDS EON PTY TP * * * * * * ;* * TA NEWS INFO N.B. SLEEP A.P.S. O.T.T. kHz MEMO. MHz PROG. O.T.T. indicator Memory indicator Timer Program indicator A.P.S.
Controls and indicators 15 R-SE9T/DP-SE9/X-SE9 (En) Receiver R-SE9T 1 N.B. key (t When the power is ON : Used for bass compensation. When the power is OFF : Used for timer setting. 2 “enter” key ¶r Used for time setting, timer setting, presetting RDS stations, storing radio stations etc. 3 “auto/mono” key ¶r When the power is ON : The tuning mode is switched. When the power is OFF : Used for clock setting. 4 “band” key §i 5 “on/standby” key * The power is switched ON and OFF (standby).
Controls and indicators R-SE9T/DP-SE9/X-SE9 (En) Remote control Unit [RC-SE9(E)] When the system control cord is connected, this remote control can be used to operate the entire system. The keys on the remote control unit with the same names as on the main unit have the same function as the keys on the main unit. 6 BAND key Basic section Preparation section 2 1 2 3 4 5 6 7 8 9 3 SLEEP 1 ¡ 7 DISPLAY 1 2 3 RANDOM 4 5 6 CLEAR 7 8 9 P.MODE O.T.E.
Operation of remote control unit Operation of remote control unit 17 R-SE9T/DP-SE9/X-SE9 (En) Loading batteries 1 Remove the cover. 2 Insert batteries. 3 Close the cover. Operation ÷ When pressing more than one remote control keys successively, press the keys securely by leaving an interval of 1 second or more between keys. 6m 30° 30° Model: RC-SE9(E) Infrared ray system 1.The provided batteries are intended for use in operation checking, and their service life may be short. 2.
Hearing sound Hearing sound R-SE9T/DP-SE9/X-SE9 (En) Basic use Bass compensation 2 Listening through headphones 1 Basic section Preparation section 3 Muting the sound temporarily Press the “on/standby” key of the receiver. When the “on/standby” key is pressed while the power is ON, the power will be switched OFF. Application section 1 on/standby Turn the “multi control” knob multi control 2 Knowledge sections 1. Switching the power ON (OFF). volume control 2.
Hearing sound 19 R-SE9T/DP-SE9/X-SE9 (En) Muting the sound temporarily (Remote control unit only) MUTE R-SE9T Blinks Listening through headphones 1 Insert the headphone plug into the phones jack. phones MUTE Remote control unit ÷ Press again to resume the original volume. ÷ This is also cancelled when the volume is adjusted. Bass compensation (N.B.: Natural Bass circuit) R-SE9T Lights NB ÷ Headphones with a stereo mini plug can be connected. ÷ The sounds from all speakers are cut off.
Hearing sound R-SE9T/DP-SE9/X-SE9 (En) Basic section Preparation section Playback of CD 1 Playback from desired track 0 Application section Skipping tracks To stop PLAYBACK 1. Load a disc. 1 The label must be on top. 1 Open the tray. 2 Place a disc. 3 Close the tray. The tray opens when the key is pressed and closes when the key is pressed again. 2. Start playback.
Hearing sound 21 R-SE9T/DP-SE9/X-SE9 (En) Skipping tracks To fast forward and backward 4 1 ¢ To skip backward To backward To skip forward To forward ÷ Playback starts from the position where the key is released. To pause playback 6 Playback from desired track Select the desired track No. 1 2 3 4 5 6 7 8 9 0 PTY SEARCH +10 ÷ Each press pauses and plays the CD alternately.
Hearing sound R-SE9T/DP-SE9/X-SE9 (En) Playback of tape Selection of reverse mode Preparation section Selection of DOLBY NR 2 Basic section 1 To wind tape at high speed To stop playback 1. Load a cassette tape. 1 Open the tray. 2 Insert a tape and close the tray. Application section 0 1 Top side Side where tape is exposed Reverse side 2. Start playback. Knowledge sections 2 3 2 The tape direction lights green. Press the key for the running direction to be played.
Hearing sound 23 R-SE9T/DP-SE9/X-SE9 (En) To pause the tape To stop playback 8 7 ÷ Press the 2 or 3 key to restart playback. Selection of DOLBY NR (Noise Reduction) To wind tape at high speed 1 ¡ The Dolby NR system minimizes the hiss noise heard when playing tape. To fast wind in direction \ ÷ Press the 7 key to stop fast winding. B C Dolby NR Selection of reverse mode Preparation section To fast wind in direction | ÷ The tape direction lights red. ∏ rev.
Hearing sound R-SE9T/DP-SE9/X-SE9 (En) DPSS DPSS (Direct Program Search System) detects an unrecorded part of 4 seconds or more as the interval between tracks and permits easy operation of cassette tape like a CD. Skip search Plays the desired music program from the beginning by skipping programs until you reach the desired program. Up to 16 programs can be skipped. During playback of top side (while 3 is lit) To play the next program : Press once.
Hearing sound 25 R-SE9T/DP-SE9/X-SE9 (En) One-program repeat playback Plays a single music program repeatedly up to 16 times. Press during playback. During playback of top side (while 3 is lit) 2 3 ÷ The program being played will be repeated 16 times, after which normal playback resumes. ÷ When the 7 key is pressed, playback stops and the oneprogram repeat is canceled.
Hearing sound R-SE9T/DP-SE9/X-SE9 (En) Receiving broadcast station It is also possible to receive them by one-touch operations by storing up to 40 stations in the preset memory. Collective presetting of stations (auto preset) One-by-one presetting (manual preset) 2 2 Basic section Preparation section 1 Preset call 1. Select the broadcast band. band Each press alternates the band. Application section 1 2. Select a station.
Hearing sound 27 R-SE9T/DP-SE9/X-SE9 (En) Collective presetting of stations (auto preset) 1 Receive a FM broadcast. 2 Keep the "enter" key depressed (for 2 sec or enter more). During recording, the indicator “A MEMO” flashes. ÷ Up to 30 stations can be memorized. ÷ For use of the RDS function, stations must be memorized by RDS auto presetting. ÷ RDS stations are given priority during auto presetting. If there is memory left after presetting, the receiver continues presetting regular FM stations.
Recording Recording R-SE9T/DP-SE9/X-SE9 (En) Recording Note Note that this cassette deck cannot record onto Metal tapes. Preparation section 4 Basic section Application section 2 5 3 0 Top side 1. Load a tape in deck. 1 1 Open the tray of the cassette deck. 2 Insert a tape. 3 Close the tray. ÷ Differentiation between normal (TYPE I) and high (TYPE II) tape is set automatically. ÷ Remove tape slack before loading. Reverse side Check the tape transport direction indicator.
Recording 29 R-SE9T/DP-SE9/X-SE9 (En) Temporary stop during recording An unrecorded section of about 4 sec is produced (auto recording mute) 8 1 Obtain stop condition. 8 2 Press the record key twice. ¶ About 4 sec ¶ 8 ¶ ÷ Press the record key to restart recording. ¶ An unrecorded section of about 4 sec is produced directly after the recording has been interrupted. 8 ¶ ÷ An unrecorded section of about 4 sec is produced and recording pause condition is reached.
Recording R-SE9T/DP-SE9/X-SE9 (En) To repeat a recording ÷ If there is a non-recorded space of more than 4 seconds before the recording start position, recording is aborted and tape is rewound as shown below. Return to the recording start position. Press the rewind key during recording. During recording of reverse side (while 2 is lit) 1 ¡ Preparation section ÷ If there is no recorded tune before, the tape will be rewound then stopped.
Playback of CD Playback of CD 31 R-SE9T/DP-SE9/X-SE9 (En) Listening in the desired sequence (program playback) Any tracks on the discs in the tray can be listened to in the desired sequence. (Max. 32 tracks) Select the “CD” input. If it is in play mode DP-SE9 7 TRACK NO. 0 1 2 Light the “PGM” indicator. 0: 0 0 Lights 2 3 4 5 6 7 8 9 10 11 DP-SE9 P.MODE PGM 1 TRACK NO. Basic section 0 1 3 Enter track Nos. in the order you want to play them. 1 Select the track.
Playback of CD R-SE9T/DP-SE9/X-SE9 (En) Preparation section To add a track to the program 1 Select the track. 1 2 3 4 5 6 7 8 9 0 PTY SEARCH +10 ÷ When a track No. is entered, the track will be added to the end of the existing program. 2 Press the P. MODE key. To delete a programmed track Basic section CLEAR ÷ Each time the key is pressed, the last track will be deleted. ÷ A track being played can not be deleted. Application section To quit the program mode Goes off P.
Playback of CD 33 R-SE9T/DP-SE9/X-SE9 (En) Repeated playback Desired tracks or discs can be played back repeatedly. Select the “CD” input. To repeat a disc Confirm that this is not lit. DP-SE9 TRACK NO. PGM If the “PGM” indicator is lit, press the P.MODE key to turn it off. Preparation section 1 Confirm that the “PGM” indicator is not lit. 0 1 2 Press the “repeat” key. Lights repeat DP-SE9 TRACK NO. REPEAT Basic section 0 1 3 Start playback.
Playback of CD R-SE9T/DP-SE9/X-SE9 (En) Listening to an unexpected track sequence (random playback) As the tracks each time are selected randomly, the music can be enjoyed. Preparation section Select the “CD” input. 1 Confirm that the “PGM” indicator is not lit. If the “PGM” indicator is lit, press the P.MODE key to turn it off. Confirm that this is not lit. DP-SE9 P.MODE PGM TRACK NO. 0 1 Basic section 2 Press the RANDOM key. DP-SE9 TRACK NO.
Convenient CD recording Convenient CD recording 35 R-SE9T/DP-SE9/X-SE9 (En) Selecting the optimum recording method With this unit, the following edit recording is possible according to the purpose. Note Note that this cassette deck cannot record onto Metal tapes. \ Edit recording of CD is possible by the simple operation of entering the recording length of the tape. If you want to select the tracks to be recorded while playing a CD \ (ONE TOUCH EDIT.....
Convenient CD recording R-SE9T/DP-SE9/X-SE9 (En) Giving preference to the tape length over the track sequence (time edit recording) When the tape recording time is specified, recording is executed with changing the track sequence so that no track will be interrupted when the tape direction is changed at the end of one side. Preparation section Recording preparations are required.• (Steps 1 to 4) 1 Select the “EDIT” mode. Confirm that this is not lit 1 Confirm that the “PGM” indicator is not lit.
Convenient CD recording 37 R-SE9T/DP-SE9/X-SE9 (En) Recording only desired tracks (ONE TOUCH EDIT.....single track recording) At the time of CD playback, any desired track can be selected immediately for recording. When playing an MD with the DM-SE9 (option), the same procedure can be used to record only that track on tape. Recording preparations are required.• (Steps 1 to 4) Select a mode other than random play. DP-SE9 6 TRACK NO.
Convenient CD recording R-SE9T/DP-SE9/X-SE9 (En) One-touch recording of an entire CD (ONE TOUCH EDIT.....recording of all tracks) When the O.T.E. key is pressed while the CD player is in the stop mode, recording of a CD can be started at the same time as playback. When the DM-SE9 (option) is connected and the input selector is set to “MD”, the same procedure can be used to make a one-touch recording of the entire MD on tape. Preparation section Recording preparations are required.
R.D.S. (Radio Data System) R.D.S. 39 R-SE9T/DP-SE9/X-SE9 (En) RDS is a system which transmits useful information (digital data) for FM broadcasts together with the broadcast signal. Tuners and receivers designed for RDS reception can extract the information from the broadcast signal for use with various functions such as automatic display of the station name. For reception of RDS stations, the RDS auto presetting function must be used to preset the stations.
R.D.S. R-SE9T/DP-SE9/X-SE9 (En) Searching for a desired program type (PTY search) By specifying the type of program (genre) you want to listen to, the tuner automatically searches for a station which is currently broadcasting a program of the specified type. For reception of RDS stations, the RDS auto presetting function must be used to preset the stations. ¶ Preparation section Set the reception band to FM. 1 Activate the PTY search mode. RDS NEWS PTY 2 Select the program type you desire.
R.D.S. 41 R-SE9T/DP-SE9/X-SE9 (En) EXAMPLE: Searching for a Rock Music broadcast. PTY SEARCH +10 Display while searching AUTO ST. TUNED Blinks RDS ROCK R-SE9T PTY Preparation section 3 Start the search. M Program type name display Repeat steps 1, 2 and 3 • When the PTY is received, the PTY name blinks and the “PTY” lights up. Display when a station is received. Goes out AUTO ST.
R.D.S. R-SE9T/DP-SE9/X-SE9 (En) To be able to listen to the desired information at any time (EON reservation) By using the EON function, which manages the information of other stations, listening to desired information like traffic information or news etc. can be reserved even when it is not being transmitted at the present.
Compensating for the bass and treble tones 43 R-SE9/DP-SE9/X-SE9 (En) Compensation by adjusting the bass and treble levels Use the multi control knob. ... The levels of the bass and treble tones can be set independently. Compensation by applying the preset compensation levels Use the EX. BASS function. ... The levels of the bass and treble tones are enhanced by the preset levels. The bass level enhancement is effective in listening at a low volume.
Clock adjustment R-SE9T/DP-SE9/X-SE9 (En) This unit incorporates a clock function. Be sure to adjust the correct time before using the timer function. Preparation section Ensure that the power is OFF. 1 Activate the clock adjustment mode. Example: Adjustment to 8:45 R-SE9T auto/mono AM 1 2 :) ) Basic section ÷ The time display starts to blink. 2 Enter the hour.
Timer operation Timer operation Adjust the clock before setting the timer. 45 R-SE9T/DP-SE9/X-SE9 (En) Operate easy To use Timer (O.T.T.) Playback of the selected input source starts at the specified time, and the power is switched off after one hour. This timer operates only once directly after setting. Sleep timer The power is turned OFF automatically after the specified period has elapsed.
Timer operation Adjust the clock before setting the timer. R-SE9T/DP-SE9/X-SE9 (En) Timer programming This is a 24 hour timer. Select the time and duration for the operation and the contents, and select operation or no operation as required. Basic section Insert a disc. (Program playback is not possible.) ÷ To listen to tape Set a tape into deck. ÷ Listening to MD Set a disc into the MD recorder. ............................ The station should be preset prior to the above.
Timer operation Adjust the clock before setting the timer. 47 R-SE9T/DP-SE9/X-SE9 (En) 5 Enter the ON time. 1 ÷ After entering the “hour” with the procedure in 1 and 2, enter the “minute” using the same procedure. multi control R-SE9T To decrease the figure enter To increase the figure AM 2 7 :) ) PROG. ÷ If you commit a mistake, restart from step 4. 6 Enter the OFF time. ÷ After entering the “hour” with the procedure in 1 and 2, enter the “minute” using the same procedure.
Timer operation Adjust the clock before setting the timer. R-SE9T/DP-SE9/X-SE9 (En) 8 Set the program. ÷ The “PROG.” indicator lights. R-SE9T mode 1 ) :) 5 PROG. ÷ The timer does not operate when no program is set. Preparation section This completes the program timer reservation. Please refer to the following item for confirmation, changes, etc. Ensure that the power is OFF. Note Check the reservation content. The reservation contents cannot be cleared.
Important Items Important Items 49 R-SE9T/DP-SE9/X-SE9 (En) Handling of discs and tapes Disc handling precautions Handling Hold compact discs so that you do not touch the playing surface. Sticker If fingerprints or foreign matter become attached to the disc, lightly wipe the disc with a soft cotton cloth (or similar) from the center of the disc outwards in a radial manner. Storage When a disc is not to be played for a long period of time, remove it from the CD player and store it in its case. ......
Important Items R-SE9T/DP-SE9/X-SE9 (En) Maintenance Preparation section Cleaning the head section Cleaning the heads and peripheral components Demagnetizing the head For maintaining the best condition of the deck and for longer service life, always keep the heads (recording / playback / erase), capstan and pinch roller clean. For the cleaning, use a cleaning cassette available in audio stores. For details, read the instruction manual of your cleaning tape.
Important Items 51 R-SE9T/DP-SE9/X-SE9 (En) Reference Beware of condensation When water vapor comes into contact with the surface of a cold material, condensation is produced. If condensation occurs, correct operation may not be possible, or the unit may not function correctly. This is not a malfunction, however, and the unit should be dried-out. (To do this, turn the power switch ON and leave the unit as it is for several hours.
In case of difficulty In case of difficulty R-SE9T/DP-SE9/X-SE9 (En) What appears to be a malfunction may not always be serious. If your unit should not perform as expected, consult the table below to see if the problem can be corrected before seeking help from your dealer or service representative. Operation to reset The microcomputer may fall into malfunction (impossibility to operate, erroneous display, etc.) when the power cord is unplugged while power is ON or due to an external factor.
In case of difficulty R-SE9T/DP-SE9/X-SE9 (En) Receiver unit, speakers Symptom Cause Remedy After presetting, reception is not possible with preset call. ÷ The frequency of the preset station is not tunable. ÷ The preset memory has been cleared because the power cord has been unplugged for a long period. ÷ Preset stations with tunable fre- ¶ quencies. ÷ Preset stations again. ¶ Cause Remedy Cassette deck unit Symptom ÷ Clean the head referring to “Maintenance”.
In case of difficulty R-SE9T/DP-SE9/X-SE9 (En) Cassette deck unit Symptom Cause Remedy Recording cannot be started by pressing the record key. ÷ The recording protect tab of the cassette has been broken. ÷ The TAPE input is selected. ÷ Use a cassette with an unbroken re- o cording protect tab or block the hole. ÷ Select the source to be recorded ª with the input selector key. ÷ Change the tape transport direc- • tion or reverse the tape insertion orientation.
Specifications R-SE9T/DP-SE9/X-SE9 (En) Receiver (R-SE9T) [Amplifier section] [FM Tuner section] [AM Tuner section] Tuning frequency range ................ 531 kHz ~ 1,602 kHz Usable sensitivity (30% mod., S/N 20 dB) .................................................... 12 µV / (500 µV/m) Signal to noise ratio (at 30% mod., 1 mV input) ........................................................................... 48 dB Output level / Impedance (30% mod., 1 mV input) .....................................
Knowledge section Application section Basic section Preparation section R-SE9T/DP-SE9/X-SE9 (En) For your records Record the serial number, found on the back of the unit, in the spaces designated on the warranty card, and in the space provided below. Refer to the model and serial numbers whenever you call upon your dealer for information or service on this product.