TK-7302/ TK-8302 VHF FM Transceiver/ UHF FM Transceiver Instruction Manual ÉMETTEUR-RÉCEPTEUR FM VHF/ ÉMETTEUR-RÉCEPTEUR FM UHF MODE D’EMPLOI TRANSCEPTOR FM VHF/ TRANSCEPTOR FM UHF MANUAL DE INSTRUCCIONES RICETRASMETTITORE FM VHF/ RICETRASMETTITORE FM UHF Manuale di Istruzioni VHF-FM-TRANSCEIVER/ UHF-FM-TRANSCEIVER Bedienungsanleitung VHF FM ZENDONTVANGER/ UHF FM ZENDONTVANGER Gebruiksaanwijzing VHF FM EL TELSİZİ/ UHF FM EL TELSİZİ KULLANIM KILAVUZU © B62‑2169‑10 (E) 09 08 07 06 05 04 03 02 01
ENGLISH VHF FM TRANSCEIVER/ UHF FM TRANSCEIVER TK-7302/ TK-8302 Instruction Manual Firmware Copyrights The title to and ownership of copyrights for firmware embedded in Kenwood product memories are reserved for Kenwood Corporation. NOTIFICATION This equipment complies with the essential requirements of Directive 1999/5/EC. The use of the warning symbol means the equipment is subject to restrictions of use in certain countries.
Information on Disposal of Old Electrical and Electronic Equipment and Batteries (applicable for EU countries that have adopted separate waste collection systems) Products and batteries with the symbol (crossed-out wheeled bin) cannot be disposed as household waste. Old electrical and electronic equipment and batteries should be recycled at a facility capable of handling these items and their waste byproducts. Contact your local authority for details in locating a recycle facility nearest to you.
Thank You We are grateful you have chosen Kenwood for your personal mobile applications. This instruction manual covers only the basic operations of your mobile radio. Ask your dealer for information on any customized features they may have added to your radio. Notices to the User ◆ Government law prohibits the operation of unlicensed transmitters within the territories under government control. ◆ Illegal operation is punishable by fine and/or imprisonment. ◆ Refer service to qualified technicians only.
Precautions Observe the following precautions to prevent fire, personal injury, and transceiver damage. • Do not attempt to configure the transceiver while driving; it is too dangerous. • Do not disassemble or modify the transceiver for any reason. • Do not expose the transceiver to long periods of direct sunlight, nor place it near heating appliances. • If an abnormal odor or smoke is detected coming from the transceiver, switch the transceiver power off immediately, and contact your Kenwood dealer.
GETTING STARTED Note: The following instructions are for use by your Kenwood dealer, an authorized Kenwood service facility, or the factory. Supplied Accessories Carefully unpack the transceiver. We recommend that you identify the items listed below before discarding the packing material. If any items are missing or have been damaged during shipment, file a claim with the carrier immediately. DC power cable (with fuses) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
n Installing the Transceiver For passenger safety, install the transceiver securely using the supplied mounting bracket and screw set, so the transceiver will not break loose in the event of a collision. Note: Before installing the transceiver, check how far the mounting screws will extend below the surface. When drilling mounting holes, be careful not to damage vehicle wiring or parts. 1 Mark the position of the holes in the dash, using the mounting bracket as a template. Using a 4.
GETTING ACQUAINTED Front/Rear Panel : @ . ; ACC. = B> ① ② ③ ④ ⑤ ⑥ ⑦ ⑧ ⑨ ⑩ ⑪ ⑫ ⑬ ⑭ 2 8 (Power) switch Press to switch the transceiver ON or OFF. / keys Press to activate their programmable functions {page 4}. Display Refer to page 4. / keys Press to activate their programmable functions {page 4}. TX/RX Indicator Lights red while transmitting. Lights green while receiving a signal. Flashes orange when receiving an optional signaling call.
Display The display shows the channel number and the 2 dots show various modes of operation. The left and right dots on the display can be programmed to indicate specific modes of operation, as listed below. • Public Address • AUX • Scan Delete/Add • External Speaker • Scrambler • Horn Alert • Talk Around • Lone Worker • Zone Delete/Add • Priority Channel The right dot will blink during special operations (such as Autodial and OST).
BASIC OPERATIONS Switching Power ON/ OFF Press to switch the transceiver ON. Press again to switch the transceiver OFF. • A beep sounds and the display illuminates. • If the Transceiver Password function is programmed, “PS” will appear on the display when the power is turned ON. Refer to “Transceiver Password”, below. ■ Transceiver Password To enter the password: 1 Press / to select a digit. • When using a keypad, simply enter the password digits and proceed to step 3.
SCAN Scan monitors for signals on the transceiver channels. While scanning, the transceiver checks for a signal on each channel and only stops if a matching signal is present. To start/stop scanning, press the key programmed as Scan On/Off. • “Sc” appears on the display during Scan. • When a signal is detected, Scan pauses at that channel. The transceiver will remain on the busy channel until the signal is no longer present, at which time Scan resumes.
Scan Revert The Scan Revert channel is the channel selected when you press the PTT switch to transmit during scan. Your dealer can program one of the following types of Scan Revert channels: • Selected: The last channel selected before scan. • Selected + Talkback: Same as “Selected”, plus you can respond to calls on the channel at which scan is paused. • Priority: The Priority channel. • Priority + Talkback: Same as “Priority”, plus you can respond to calls on the channel at which scan is paused.
Stun This function is used when a transceiver is stolen or lost. When the transceiver receives a call containing a stun code, the transceiver becomes disabled. The stun code is cancelled when the transceiver receives a call with a revive code. • “St” appears on the display while the transceiver is stunned. SIGNALING Quiet Talk (QT)/ Digital Quiet Talk (DQT) Your dealer may have programmed QT or DQT signaling on your transceiver channels.
FleetSync: ALPHANUMERIC 2-WAY PAGING FUNCTION FleetSync is an Alphanumeric 2-way Paging Function and is a protocol owned by Kenwood Corporation. Selcall (Selective Calling) A Selcall is a voice call to a particular station or to a group of stations. ■ Transmitting 1 Select your desired zone and channel. 2 Press the microphone PTT switch and begin your conversation. ■ Receiving If enabled by your dealer, an alert tone will sound and the LED will blink when a Selcall has been received.
5-TONE SIGNALING 5-tone Signaling is enabled or disabled by your dealer. This function opens the squelch only when the transceiver receives the 5 tones programmed in your transceiver. Transceivers that do not transmit the correct tones will not be heard. Note: Your transceiver functions include either 5-tone Signaling or FleetSync {page 9}, but not both. Making a Selcall (Selective Calling) A Selcall is a voice call to a particular station or to a group of stations. 1 Select your desired zone and channel.
■ Lone Worker Mode Lone Worker Mode is a safety feature built into the transceiver. If the transceiver is not operated for a pre-programmed period of time, the transceiver will emit a tone and automatically enter Emergency operation. Press and hold the key programmed as Lone Worker for 2 seconds to toggle the Lone Worker function ON or OFF. • “Ln” appears on the display while Lone Worker is activated.
Monitor/ Squelch Off You can use the key programmed as Monitor or Squelch Off to listen to weak signals that you cannot hear during normal operation and to adjust the volume when no signals are present on your selected channel. Your dealer can program a key with one of 4 functions: • Monitor: Press to deactivate QT, DQT, DTMF, or FleetSync Signaling. Press again to return to normal operation. • Monitor Momentary: Press and hold to deactivate QT, DQT, DTMF, or FleetSync Signaling.
BACKGROUND OPERATIONS Time-out Timer (TOT) The Time-out Timer is used to prevent you from using a channel for an extended duration. If you continuously transmit for a preset time, the transceiver will stop transmitting and an alert tone will sound. Release the PTT switch. Auxiliary Port Press the key programmed as AUX to activate the auxiliary port. The auxiliary port is used with optional boards. • “AU” appears on the display when the auxiliary port is active.
