Owner's Manual
Table Of Contents
Installation
························1
··1
!
"r
0
e
~I~
~!~
33
0
33
0>1:::;
IlIlll!/lXI)
~~
OJ~
0
@
--.33
~
o·
-
~
~~
• Accessories
Part name
External Number
View
of
Items
Selftapping screws
@)mn>
4
(05
xl8
mill
(3/16" x 11/16"))
Hexagon Wrench (Large)
r
1
_.
Hexagon Wrench (Small)
~
1
-'-"'-'---'--'-"---'--'--"'-'-"-"'--'-"-"
..
__
._----"
..
-_._--_
.....
Terminal cover (Power
C§>
1
terminal)
....
~-
.•..
_
.....
'
• Installation procedure
Since there
are
larCJe
variety
of
settir,gs and
connections possible according
to
applications, read
the instruction manual well
to
select the proper
setting and connection.
I. Remove the ignition key and disconnect the
ne~Jative
8 terminal
of
the battery to prevent short
circuits.
2.
Set
the unit according
to
the intended usage
3.
(onnect
the input and
output
wires
of
the units.
4.
Connect the speaker wires.
5.
Connect the power wire, power control wire and
grounding wire foilowing this order.
6.
Install the installation fittings
in
the unit.
7.
Attach the unit.
8.
Install the reniote controller'.
9.
Connect the negative
()
terminal
of
the battery.
4
English
Self-tapping screw
(05 x
18
mm
(3/16" x 11/16"))
~
1
:).7"./~
~.l7I'''~
'7",,~
.........
,
/
Installation board, etc.
(tilickness :
15
mm
(9/16") or rnore)
IA CAUTION I
Do
not
install in
the
below
locations;
(Unstable location, In a location that interferes
with
driving,
In
a location that gets wet, In a dusty
location,
In
a place that gets hot, In a place that
gets direct sunlight, In a location
that
gets
hit
by
hot
air)
• Do
not
install the
unit
under
the carpet.
Otherwise heat
build-up
occurs and
the
unit
may
be damaged.
• Install this
unit
in a location vvhich allows heat
to
easily dissipate
Once installed,
do
not
place any
object
on
top
of
the unit.
The surface temperature
of
the
amplifier will
become
hot
during
use
Install
the
amplifier in a
place where people, resins, and
other
substances
that
are
sensitive
to
heat will
not
corne
into
contact
with
it.
• This
unit
has
c:()olin~J
fan
to
decrease
the
internal
temperature. Do
not
mount
the
unit
in a place
where the cooling fan and duets
of
the
unit
are
blocked. Blocking these openings will
inhibit
the
cooling
of
the internal temperature and result in
rnalfurKtion.
• When making a hole under a seat, inside the
tr'unk, or somewher'e else in the vehicle, check
that there
is
nothing
hazardous on the opposite
side such
as
a gasoline tank, brake pipe,
or
v'firing
harness, and be careful
not
to
cause scratches or
other
damage.
Do
not
install near the dashboard, rear tray, or air
bag safety parts.
The
installation
to
the vehicle should securely
fasten the
unit
to a place in which it will
not
obstruct driving. If the
unit
comes
off
due
to
a
shock and hits a person
or
safety part, it may
cause injury or
an
accident.
•
Nter
installing
the
unit, check
to
make sure that
electrical
equipment
such
as
the brake lamps.
tum
signal lamps and windshield wipers operate
normally.