KENYON INSTALLATION & USER’S GUIDE for Models 213 & 436 Alcohol/Electric Combination Stove KENYON P.O. Box 925 #8 Heritage Park Road Clinton, CT 06413 USA Phone: (860) 664-4906 Fax: (860) 664-4907 Revision 07.20.
INTRODUCTION Thank you for purchasing a KENYON Alcohol/Electric combination stove. The operation instructions that follow are for the models 213 (single burner) and 436 (double burner) alcohol/electric combination stoves. These units feature counter-top mounting, self-priming / self pressurized alcohol burners. The electric portion of the stove operates on 120 VAC (or 240 VAC depending on KENYON Model #). KENYON marine stoves have been engineered exclusively for the marine environment.
KENYON Model # B61044 B61045 B61046 B61047 B61048 B61049 Stove Description Voltage AC Rated Wattage (W) & Amps (A) 213 A/E w/ Black Glass Lid 213 A/E w/ Black Glass Lid 213 A/E w/ White Glass Lid 213 A/E w/ White Glass Lid 436 A/E w/ Black Glass Lid 120 Volts - 60 Hz 1100 W / 10 A 240 Volts - 50/60 Hz 1100 W / 5 A 120 Volts - 60 Hz 1100 W / 10 A 240 Volts - 50/60 Hz 1100 W / 5 A 120 Volts – 60 Hz 2200 W / 20 A 436 A/E w/ Black Glass Lid 240 Volts - 50/60 Hz 2200 W / 10 A Suggested Wire S
LOCATION & COUNTER-TOP PREPARATION The stove must be located in an area with adequate ventilation for occupants’ safety and efficient stove operation. It should be installed with adequate clearances between the stove top and all surrounding surfaces (i.e. curtains, cabinets, etc) in order to minimize heat transfer to these surfaces. Also fire resistant materials should be attached to any surrounding surfaces, especially overhead.
Remove the back cover on the stove; push the cable through 7/8” (22 mm) hole below the terminal board, using the black plastic grommet to protect the supply cable. Connect the ungrounded current carrying conductor to terminal marked L1. Connect the other ungrounded current carrying conductor (or neutral carrying conductor- 120V only) to the terminal marked L2. Connect the ground wire (green) to the left terminal marked G. A cable clamp is provided to secure cable.
• DO NOT TOUCH HEATING ELEMENTS - Heating element areas may be hot even though they are dark in color. These areas may be hot enough to cause burns. During and after use, do not touch, or let clothing or other flammable materials contact heating element areas until heating elements have had sufficient time to cool. Other surfaces of the appliance may become hot enough to cause burns. • Servicing- Do not attempt to repair or replace any part of your KENYON stove.
ALCOHOL BURNER OPERATING INSTRUCTIONS Before attempting to operate the stove, please read the theory and operating instructions carefully and become thoroughly familiar with the various parts of the stove and how they operate. An internal parts diagram has been provided below to illustrate burner functions and characteristics under normal operating conditions. Theory This patented burner system incorporates an internal tank in the burner assembly that does not require any external pressurization.
Operating Components A Fill Cap is located on each burner with a rubber washer (gasket) underneath each fill cap. Be sure the washer is in place and the fill cap is reasonably tight when operating the stove. If either are lost or damaged replace at once. DO NOT ATTEMPT TO OPERATE THE BURNER WITHOUT A CAP OR WITH ANY NON COMPATIBLE REPLACEMENT. The alcohol burner control wheel(s) are located in the front flange of the stove. The purpose of the control wheel is to regulate the burner flame.
8. Wipe any alcohol spills and replace the air deflector assembly into the pan and return the electric element back into place. Note that the electric element serves as a grate when using the alcohol burner to cook. Alcohol Burner Operating Instructions 1. Completely open the flame control cap by rotating the control wheel to the left. 2. Ignite the small fiber wick located in the center chimney. A match may be used or a Bar-B-Que grilligniting wand is ideal.
CLOSING THE GLASS LID If your KENYON stove is equipped with a glass lid, care should be followed when lowering the lid onto the stove. NEVER CLOSE THE LID ON AN OPEN FLAME OR AN ELECTRIC ELEMENT THAT IS HOT OR TURNED “ON”. Make sure that the appliance is cool before lowering the glass lid onto the frame. When the lid is in an open position, the “lid-stay” arm that is attached to the glass “locks” onto the large lock screw.
Stove Replacement Parts A B H G C D E I L F K A B C D E F G H I J K L not shown not shown not shown 436 Model Shown J PART # DESCRIPTION B93077 B93075 240360 H2003-1 H1950 240385 B93090 240342 B93086 B93087 043200 240338 240400 240407 141485 141580 H1947-1 H1947-2 240378 240403 240405 Air Deflector Assembly Air Deflector Assembly Electric Element Assembly- 120 Volts Electric Element Assembly- 240 Volts Indicator Light- 120 Volts Indicator Light- 240 Volts Fill Cap w/ Rubber Washer Gasket Non Pr
WARRANTY Kenyon International, Inc (the "Company") warrants its products in normal usage to be free of defects in materials and workmanship subject to the conditions and limitations below. Any part, which proves to be defective in normal usage during the warranty period will be repaired or replaced by the Company. This warranty is subject to the following conditions and limitations: 1.