www.CookWithKenyon.
Table of Contents Section Page Important Safeguards ............................................................................................................... 3 Product Specifications ..............................................................................................................6 Installation Instructions Step # 1 - Unpacking the Cooktop ....................................................................................
IMPORTANT SAFEGUARDS Please read these instructions in their entirety before installation and use. The following information applies to all KENYON Electric Cooktops. This cooktop, like all appliances, has the potential to create safety problems through careless and improper use. Please observe all of the following safety precautions. Proper Installation. Be sure your appliance is properly installed and grounded by a qualified technician. Never use your appliance for warming or heating the room.
Use only dry pot holders. Moist or damp pot holders on hot surfaces may result in burns from steam. Do not let pot holders touch the elements on the appliance. Do not use a towel or other bulky cloth in place of a pot holder. Do not cook on broken cooktop. If cooktop should break, cleaning solutions and spillovers may penetrate the broken cooktop and create a risk of electric shock. Contact an authorized service center or KENYON Customer Care immediately at (860) 664-4906. Clean cooktop with caution.
WARNING: If the surface is cracked, switch off the appliance to avoid the possibility of electric shock. Metallic objects such as knives, forks, spoons and lids should not be placed on the cooktop/hob surface since they can get hot. The appliance is not intended to be operated by means of an external timer or separate remotecontrol system. Danger of fire: Do not store items on the cooking surfaces. CAUTION: The cooking process has to be supervised.
PRODUCT SPECIFICATIONS Lite-Touch Q® Series 2-Burner Large Models B41540 - 120V AC - one 6.5” (165mm) @ 1200 watts one 8” (200mm) @ 1400 watts B41549 - 208V AC - one 6.5” (165mm) @ 1200 watts one 8” (200mm) @ 1800 watts B41541 - 240V AC - one 6.5” (165mm) @ 1200 watts one 8” (200mm) @ 1800 watts B41540L - 120V AC - one 6.5” (165mm) @ 1200 watts one 8” (200mm) @ 1400 watts B41549L - 208V AC - one 6.
Lite-Touch Q® & Lite-Touch Q® Cortez Series 2-Burner Trimline Models B41575, B41775 & B41775T30 - 120V AC - two 6.5” (165mm) @ 1200 watts B41579, B41579T30, B41779 & B41779T30 - 208V AC - two 6.5” (165mm) @ 1200 watts B41576, B41576T30, B41776 & B41776T30 - 240V AC - two 6.5” (165mm) @ 1200 watts B41575L, B41575LUST30, B41775L & B41775LT30 - 120V AC - two 6.5” (165mm) @ 1200 watts B41579L, B41579LT30, B41779L & B41779LT30 - 208V AC - two 6.
Lite-Touch Q® Glacier Series 2-Burner XL Models B41796 & B41796T30 - 120V AC - one 6.5” (165mm) @ 1200 watts one 8” (200mm) @ 1400 watts B41798 & B41798T30 - 208V AC - one 6.5” (165mm) @ 1200 watts one 8” (200mm) @ 1800 watts B41797 & B41797T30 - 240V AC - one 6.
INSTALLATION GUIDE Important: Save this document for review by local inspector. ! Important: This appliance must be properly installed and grounded by a qualified technician. STEP # 1 Unpacking the Cooktop Carefully unpack the cooktop from its shipping container. If possible, retain the original shipping carton and protective packaging in the event the unit ever has to be returned for service. Verify and identify the package contents. The following items should be included in the carton.
For future reference, please record the serial number of your cooktop here: STEP #2 Check the Electrical Supply Requirements This product must be installed in accordance with national, state and local electric codes. The following table provides the correct voltage, amperage and frequency that must be supplied to the cooktop.
! Warning: FOR ELECTRICAL CONNECTION OF TRIMLINE TOUCH CONTROL COOKTOPS IN CANADA ELECTRICAL CONNECTION: It is the responsibility of the purchaser to be sure your appliance is properly installed and grounded by a qualified technician. Install per Canadian Electrical Code, CSA Standard C22.1 and local codes and ordinances. ELECTRICAL REQUIREMENTS: This unit must be connected to a power source with the correct voltage to match the voltage indicated on the data plate of the unit.
A - 13 inches maximum depth of overhead cabinets B - 36 inches is minimum height of countertop above floor C - The minimum flat countertop surface that the cooktop will rest upon must be equal to or greater than the overall cooktop dimensions (refer to the following page for overall cooktop dimensions).
Since the appliance requires a sufficient supply of fresh air to operate at maximum performance, the cabinet must be designed accordingly. The following is required for this: • The cabinet must have a minimum of two openings; one to allow fresh air to enter and the other for hot air to escape the cabinet. • Opening sizes must be equal to 8 square inches each. This is for ambient temperatures of 85ºF / 30ºC and below.
12” 12” 21” 21” 3 1/4” 3 1/4” 20" 20" 10 3/4" COUNTERTOP CUTOUT DIMENSIONS Models B41575, B41576, & B41579 2 BURNER TRIMLINE PORTRAIT 10 3/4" COUNTERTOP CUTOUT DIMENSIONS 2 BURNER TRIMLINE LANDSCAPE Models B41575L, B41576L, & B41579L NOTE: When making countertop cutout, radius the corner of the cutout (1/4” radius is typical). This will prevent cracking of the countertop. Follow the countertop manufacturer’s instructions regarding the minimum corner radius and reinforcement of corners.
STEP #4 silicone to seal the glass edge if desired Installing the Cooktop The cooktop is supplied with two metal mounting brackets. These brackets are designed to hold the cooktop firmly in place. The cooktop does not have a metal frame and should be sealed to the countertop. Use a soft bedding compound that will prevent damage if later removal for service is necessary. We recommend a nonadhesive type of sealant, such as plumber’s putty, maximum compressed thickness of 1/16”.
STEP #5 Electrical Connection Before proceeding further, verify that the power supply is disconnected. Verify that the appropriate electrical supply requirements have been met. Please refer to the table on page 10 for appropriate electrical requirements. The cooktop is supplied with a 36-inch long conduit for a connection to an accessible junction box. The 240V and 208V conduit consists of three insulated wires.
OPERATION READ SAFETY INSTRUCTIONS BEFORE OPERATING YOUR APPLIANCE The cooking surface and control areas of your Lite-Touch Q® cooktop are identified by permanent patterns in the cooktop. The appliance is easy to maintain and easy to clean.
Key graphic for lock function Lock function button Element indicator graphic Element heat level indicator Lock function LED Element ON/OFF button Master power button Master power LED Hot surface indicator LEDs Master power graphic - button decreases heat setting + button increases heat setting Element activation LED Fig.
HOT SURFACE INDICATOR A hot surface indicator light will illuminate when an element is energized and has been activated for enough time to produce unsafe to touch temperatures of the cooking surface. The light will remain illuminated until the surface is cool. SAFETY THERMAL CUTOUT Another safety feature of the Lite-Touch Q® cooktop is the thermal cutout. If the temperature of an element reaches unsafe levels, the thermal cutout will open and power to that element will be turned off.
CLEANING To help ensure that the KENYON cooktop stays clean, follow these easy-care tips: Lock the cooktop before cleaning by touching and holding the key symbol for 3 seconds. Always remove food spills, grease spatters and metal rub-off from cookware. A razor blade scraper or the equivalent works well to remove spillovers. Clean the cooktop with a paper towel or a clean, soft cloth and a recommended cleaner.
Statement of Warranty KENYON Kenyon International, Inc (the “Company”) warrants its products in normal usage to be free of defects in materials and workmanship subject to the conditions and limitations below. Any part, which proves to be defective in normal usage during the warranty period will be repaired or replaced by the Company. In order for product to be covered under this warranty it must be returned to the Company for evaluation. Please contact kenyonservice@cookwithkenyon.
