www.CookWithKenyon.
Table of Contents Section Page Important Safeguards ................................................................................................................1 Product Specifications .............................................................................................................3 Installation Instructions Step # 1 - Unpacking the Cooktop ....................................................................................
IMPORTANT SAFEGUARDS Please read these instructions in their entirety before installation and use. The following information applies to all KENYON Alcohol/Electric Cooktops. This cooktop, like all appliances, has the potential to create safety problems through careless and improper use. Please observe all of the following safety precautions. Proper Installation. Be sure your appliance is properly installed and grounded by a qualified technician. Never use your appliance for warming or heating the room.
Use only dry pot holders. Moist or damp pot holders on hot surfaces may result in burns from steam. Do not let pot holders touch the elements on the appliance. Do not use a towel or other bulky cloth in place of a pot holder. Do not cook on broken cooktop. If cooktop should break, cleaning solutions and spillovers may penetrate the broken cooktop and create a risk of electric shock. Contact an authorized service center or KENYON Customer Care immediately at (860) 664-4906. Clean cooktop with caution.
PRODUCT SPECIFICATIONS Alcohol Electric Cooktop Two Burner Units B61148 - 120V AC - two 8” (200mm) @ 2200 watts B61149 - 240V AC - two 8” (200mm) @ 2200 watts Overall dimensions: Cutout dimensions: 22 1/2” x 13 1/2” x 5 3/4” 571.5mm x 342.9mm x 146mm 21 3/4” x 12 3/4” with 3” radius 552.5mm x 323.9mm with 76.
INSTALLATION GUIDE IMPORTANT: Please read these instructions completely before installation and operation of the appliance. ! STEP # 1 Unpacking the Cooktop Carefully unpack the cooktop from its shipping container. If possible, retain the original shipping carton and protective packaging in the event the unit ever has to be returned for service Verify and identify the package contents. The following items should be included in the carton. If any components are missing or damaged, call KENYON immediately.
STEP #2 Check the Electrical Supply Requirements This product must be installed in accordance with ABYC standard A-3, “Recommended Practices and Standards Covering Galley Stoves,” and/or the “Fire Protection Standards for Motorcraft” NFPA #302. The following table provides the correct voltage, amperage and frequency that must be supplied to the cooktop.
! CAUTION: Do not cut the opening in your countertop until you ensure there will be adequate horizontal and vertical clearances from the cooktop to the nearest flammable materials - fabric, plastic, wood - (except the countertop itself). Minimum Distances are: 40cm (16”) Horizontally 1M (39”) Vertically It is the installer’s and/or purchaser’s responsibility to ensure that the Cooktop is installed in a location such that a fire hazard is not created.
STEP #4 Installing the Cooktop Once the cutout has been prepared as shown on page 3, pre-fit the stove into the cutout to mark drill locations. Tilt and insert the front portion of the stove first. Care should be exercised so as not to damage or bend any moving parts. Next, lower the stove into the cut out. Using a pencil mark the location of mounting holes onto the counter. Carefully remove the stove from the cutout. Using a 1/8” drill and the pencil marks as a guide, drill four (4) mounting holes.
ALCOHOL OPERATION WARNING: OPEN FLAME COOKING APPLIANCES CONSUME OXYGEN AND PRODUCE CARBON MONOXIDE. ! TO AVOID ASPHYXIATION OR INJURY OR DEATH FROM EXPOSURE TO CARBON MONOXIDE, MAINTAIN OPEN VENTILATION WHEN USING THIS APPLIANCE. READ SAFETY INSTRUCTIONS BEFORE OPERATING YOUR APPLIANCE The cooking surface and control areas of your Alcohol Electric cooktop are identified by coil burner(s) in the cooktop. The appliance is easy to maintain and easy to clean.
ALCOHOL BURNER FUELING INSTRUCTIONS 1. The burners are designed exclusively for denatured ethyl alcohol which is readily available as “alcohol stove fuel” at marine stores. DO NOT SUBSTITUTE ANY OTHER FUEL AS FIRE OR EXPLOSION COULD RESULT. A denatured ethyl alcohol fire is readily extinguished by water, or by smothering it with a non-combustible material. 2.
WARNING: Improper stove fueling practices can result in fire and/or explosion. ! To avoid severe injury or death from fire or explosion, follow the manufacturer’s refueling instructions that are printed in your manual as well as on the stove. SELF-PRIMING / SELF PRESSURIZED BURNER Cross Sectional View Burner Jets Air Flow Air Flow Fill Cap Surrounding Chamber Center Chimney Wick ALCOHOL BURNER OPERATING INSTRUCTIONS 1.
ELECTRICAL OPERATION Controls are located in the rim of the frame: for alcohol burners, the controls are located in the front of the appliance; for electric elements, the controls are located in the sides as shown below in the figure. WARNING: NEVER OPERATE ALCOHOL BURNER(S) AND ELECTRIC ELEMENT(S) SIMULTANEOUSLY. THIS CAN CAUSE FIRE OR SEVERE INJURY. OPERATION OF ELECTRIC ELEMENTS Turn the electric control in either direction to HIGH, LOW, or any intermediate position for exact heat desired.
CLOSING THE GLASS LID If your Kenyon Custom Cooktop is equipped with a glass lid, care should be followed when lowering the lid onto the stove. NEVER CLOSE THE LID ON AN OPEN FLAME OR AN ELECTRIC ELEMENT THAT IS HOT OR TURNED “ON”. Make sure that the appliance is cool before lowering the glass lid onto the frame. When the lid is in an open position, the “lid-stay” arm that is attached to the glass “locks” onto the large lock screw.
STOVE REPLACEMENT PARTS 436 Model Shown PART # A B C D E F G H I J K B93077 B93075 240360 H2003-1 H1950 240385 B93090 240342 B93086 B93087 043200 240338 240400 240407 141585 141580 Description USED ON Air Deflector Assembly All 436 Models Lid Safety Switch Snuffer Control Arm Assembly 213 & 436 Models 213 & 436 Models Air Deflector Assembly Electric Element Assembly - 120 Volts Electric Element Assembly 240 Volts Indicator Light - 120 Volts Indicator Light - 240 Volts Fill Cap w/ Rubber Washer Ga
Warranty Kenyon International, Inc (the “Company”) warrants its products in normal usage to be free of defects in materials and workmanship subject to the conditions and limitations below. Any part, which proves to be defective in normal usage during the warranty period will be repaired or replaced by the Company. This warranty covers certain products built by the Company and is subject to the following conditions and limitations: 1.
