KENYON Custom ® SilKEN® Induction Cooktops Portrait Landscape Use & Care Guide - Installation Manual 240 V Models Kenyon International, Inc. P.O. Box 925 8 Heritage Park Road Clinton, CT 06413 Phone: 860-664-4906 Fax: 860-664-4907 www.kenyonappliances.
Table of Contents Section Page Safety Guidelines ...........................................................................................................................1 Product Specifications ..................................................................................................................3 Installation Instructions Step # 1 - Unpacking the Cooktop ........................................................................................
SAFETY GUIDELINES Please read these instructions in their entirety before installation and use. The following information applies to all KENYON Electric Cooktops. This cooktop, like all appliances, has the potential to create safety problems through careless and improper use. Please observe all of the following safety precautions. Proper Installation. Be sure your appliance is properly installed and grounded by a qualified technician. Never use your appliance for warming or heating the room.
Use only dry pot holders. Moist or damp pot holders on hot surfaces may result in burns from steam. Do not let pot holders touch the induction elements on the appliance. Do not use a towel or other bulky cloth in place of a pot holder. Do not cook on broken cooktop. If cooktop should break, cleaning solutions and spillovers may penetrate the broken cooktop and create a risk of electric shock. Contact an authorized service center or KENYON Customer Care immediately at (860) 664-4906.
SilKEN® Induction Series Cooktop PRODUCT SPECIFICATIONS B80101 - 240V AC - one 5.7” (145mm) @ 1400 watts normal, 1800 watts boost one 8.25” (210mm) @ 2300 watts normal, 3200 watts boost B80105 - 240V AC - one 5.7” (145mm) @ 1400 watts normal, 1800 watts boost one 8.25” (210mm) @ 2300 watts normal, 3200 watts boost B80201 - 240V AC - one 5.7” (145mm) @ 1400 watts normal, 1800 watts boost one 8.25” (210mm) @ 2300 watts normal, 3200 watts boost B80205 - 240V AC - one 5.
INSTALLATION INSTRUCTIONS FOR KENYON SilKEN® INDUCTION COOKTOPS Important: Save this document for review by local inspector. Important: This appliance must be properly installed and grounded by a qualified technician. STEP # 1 Unpacking the Cooktop Carefully unpack the cooktop from its shipping container. If possible, retain the original shipping carton and protective packaging in the event the unit ever has to be returned for service. Verify and identify the package contents.
For future reference, please record the serial number of your cooktop here: STEP #2 Check the Electrical Supply Requirements This product must be installed in accordance with national, state and local electric codes. The following table provides the correct voltage, amperage and frequency that must be supplied to the cooktop.
A - 13 inches maximum depth of overhead cabinets B - 36 inches is minimum height of countertop above floor C - The minimum flat countertop surface that the cooktop will rest upon must be equal to or greater than the overall cooktop dimensions (refer to the following page for overall cooktop dimensions).
14 1/2" 14 1/2" 23 1/2" 23 1/2" 3 1/4" 3 1/4" 1/4" radius in corners 1/4" Radius in corners 22 7/8" 22 7/8" 12 1/2" 12 1/2" COUNTERTOP CUTOUT DIMENSIONS Portrait Models B80101 & B80201 COUNTERTOP CUTOUT DIMENSIONS Landscape Models B80105 & B80205 NOTE: When making countertop cutout, radius the corner of the cutout (1/4” radius is typical). This will prevent cracking of the countertop.
STEP #5 Electrical Connection SilKEN® INDUCTION COOKTOP Before proceeding further, verify that the power supply is disconnected. Verify that the appropriate electrical supply requirements have been met. Please refer to the table on page 5 for appropriate electrical requirements. The cooktop is supplied with a 36-inch long conduit for a connection to an accessible juntion box. The 240V conduit consists of three insulated wires.
OPERATION READ SAFETY INSTRUCTIONS BEFORE OPERATING YOUR APPLIANCE The cooking surface areas of your SilKEN® induction cooktop are identified by inset induction zones patterns in the cooktop. The appliance is easy to maintain and easy to clean.
LOCK MODE In lock mode the heat setting cannot be changed, but the off function for both induction elements and master power will still function for safety reasons. A light next to the “key” graphic will indicate that the cooktop is locked. Refer to figure C. To lock the cooktop, place finger on the circular area next to the key graphic and hold for 1.5 seconds. An audible beep will be heard and the light next to the key graphic will illuminate. The cooktop is now locked.
CONTROLS OF INDUCTION COOKTOP To activate an induction element, first the master power must be turned on by placing and holding a finger over the circular area next to the master power graphic. An audible beep will be heard and a light next to the master power graphic will illuminate. Then the desired induction element must be turned on, by placing a finger over the circular area marked ON/OFF for that element. The same beep will sound and a light will illuminate.
SAFETY THERMAL CUTOUT Another safety feature of the induction cooktop is the thermal cutout. If the temperature of either induction element reaches 5180F (2700C), the thermal cutout will open and power to both induction elements will be turned off. This is an important safety feature designed to reduce the risk of runaway temperatures and possible risk of fire if a pot is boiled dry or unintentionally put on the cooktop empty.
CLEANING To help ensure that the KENYON cooktop stays clean, follow these easy-care tips: Lock the cooktop before cleaning by touching and holding the key symbol for 2 seconds. Always remove food spills, grease spatters and metal rub-off from cookware. A razor blade scraper or the equivalent works well to remove spillovers. Clean the cooktop with a paper towel or a clean, soft cloth and a recommended cleaner.
SilKEN® Cooktop Is Not Functioning Properly • • • SilKEN® Induction Elements Are Not Heating Properly • • Food Will Not Heat Properly • Control Panel Blinks and Cooktop Will Not Operate • 14 Combination of LED’s in horseshoe flashing repeatedly. Clear by cycling off power in circuit which supplies cooktop. Check household fuse or circuit breakers to see if it has been blown or tripped. No electricity is being supplied to the cooktop.
Warranty Kenyon International, Inc (the “Company”) warrants its products in normal usage to be free of defects in materials and workmanship subject to the conditions and limitations below. Any part, which proves to be defective in normal usage during the warranty period will be repaired or replaced by the Company. This warranty covers certain products built by the Company and is subject to the following conditions and limitations: 1.
