www.CookWithKenyon.
Table of Contents Section Page Safety Guidelines ...........................................................................................................................3 Product Specifications ..................................................................................................................7 Installation Guide Step # 1 - Unpacking the Cooktop ........................................................................................
SAFETY GUIDELINES Please read these instructions in their entirety before installation and use. The following information applies to all KENYON Electric Cooktops. This cooktop, like all appliances, has the potential to create safety problems through careless and improper use. Please observe all of the following safety precautions. Proper Installation. Be sure your appliance is properly installed and grounded by a qualified technician. Never use your appliance for warming or heating the room.
Use only dry potholders. Moist or damp potholders on hot surfaces may result in burns from steam. Do not let potholders touch the induction elements on the appliance. Do not use a towel or other bulky cloth in place of a potholder. Do not cook on broken cooktop. If cooktop should break, cleaning solutions and spillovers may penetrate the broken cooktop and create a risk of electric shock. Contact an authorized service center or KENYON Customer Care immediately at (860) 664-4906.
CONSIGNES DE SÉCURITÉ Veuillez lire la totalité de ces instructions avant d’installer ou d’utiliser cet appareil. Les informations suivantes s’appliquent à toutes les tables de cuisson électriques KENYON. Installation adéquate. Assurez-vous que votre appareil soit correctement installé et mis à la terre par un technicien qualifié. N’utilisez jamais cet appareil pour le chauffage domestique. ATTENTION Ne pas laisser sans surveillance en présence d’enfants.
Utilisez une poêle de format approprié. Cette table de cuisson comprend un ou plusieurs éléments chauffants de diamètres différents. Choisissez des ustensiles à fond plat de diamètre suffisant pour recouvrir toute la surface de l’élément chauffant. L’utilisation d’ustensiles correspondant au diamètre de l’élément augmentera le rendement de l’appareil. Ne laissez jamais sans supervision la table de cuisson réglée à chaleur élevée.
SilKEN® Induction Series Cooktop PRODUCT SPECIFICATIONS B81321 - 120V AC B81331 - 240V AC B81325 - 120V AC B81335 - 240V AC - two 6.5” (165mm) @ 1300 watts, maximum load 1800 watts combined two 6.5” (165mm) @ 1300 watts, maximum load 1800 watts combined two 6.5” (165mm) @ 1300 watts, maximum load 1800 watts combined two 6.5” (165mm) @ 1300 watts, maximum load 1800 watts combined Overall dimensions: Cutout dimensions: 8 5 6 7 21” x 12” x 3.10” 533.4mm x 304.8mm x 78.
INSTALLATION GUIDE Important: Save this document for review by local inspector. Important : Conservez ce document aux fins d'examen par l'inspecteur local. ! Important: This appliance must be properly installed and grounded by a qualified technician. Important : Cet appareil doit être installé correctement et mis à la terre par un technicien qualifié. STEP # 1 Unpacking the Cooktop Carefully unpack the cooktop from its shipping container.
For future reference, please record the serial number of your cooktop here: Name Plate Label Location STEP #2 Check the Electrical Supply Requirements This product must be installed in accordance with national, state and local electric codes. The following table provides the correct voltage, amperage and frequency that must be supplied to the cooktop.
A - 13 inches maximum depth of overhead cabinets B - 36 inches is minimum height of countertop above floor C - The minimum flat countertop surface that the cooktop will rest upon must be equal to or greater than the overall cooktop dimensions (refer to the following page for overall cooktop dimensions).
Allow a 2” minimum clearance between the bottom of the metal pan of the cooktop and any combustible surface located below, ie: the upper edge of a drawer installed below the cooktop (see Fig. B). Failure to provide proper clearance and ventilation may result in a fire hazard. NOTE: When making countertop cutout, radius the corner of the cutout (1/4” radius is typical). This will prevent cracking of the countertop.
STEP #5 Electrical Connection Before proceeding further, verify that the power supply is disconnected. Verify that the appropriate electrical supply requirements have been met. Please refer to the table on page 7 for appropriate electrical requirements. The cooktop is supplied with a 55-inch long conduit for a connection to an accessible junction box. The 240V conduit consists of three insulated wires.
OPERATION READ SAFETY INSTRUCTIONS BEFORE OPERATING YOUR APPLIANCE The cooking surface areas of your SilKEN® 2 induction cooktop are identified by permanent patterns in the cooktop. The appliance is easy to maintain and easy to clean.
INDUCTION COOKTOP CONTROL SAFETY LOCK FEATURE When the LOCK LED is illuminated in the main power control frame, the cooktop touch control power settings can’t be adjusted from the current setting. Pressing either the zone power button or the master power button however, can turn off the cooktop. The LED arc light array will no longer illuminate when in the lock mode. The lock feature can be activated at any time as a safety measure, whether the unit power is on or off.
BURNER CONTROL FRAME INDUCTION COOKTOP COOKING OPTIONS- HEATING LEVEL OR HOT SURFACE INDICATOR COOKING TEMPERATURE The induction cooktop burners can be independently operated by either a heating level ranging from low to high, or by setting a specific cooking temperature. LIGHT Power sharing between burners will take effect when both burners STANDBY are used. Refer to the Power Sharing section of this manual on page 15.
TEMPERATURE COOKING MODE Select the temperature cooking mode by touching the thermometer/gradient graphic within the chosen burner control frame. Select the desired cooking temperature, ranging from 150° to 450°F (65° to 232°C), in 10°F (12°C) increments. The selection can be made by pressing + or – buttons for each increment change, or swiping the arc. The selected cooking temperature value will illuminate and flash in 2 the control frame while the selection is in progress.
COOKTOP TIMER OPTIONS- KITCHEN TIMER AND COOKING TIMER Kitchen Timer The kitchen timer is a general timer that has many uses around the kitchen, independent of cooking activity on the induction cooktop. Activate the main power and touch the timer clock graphic within either burner control frame. Set the desired time duration by touching the + and – buttons, holding the button to increase or decrease the setting. Refer to Figure G.
TEMPERATURE UNITS AND TIMERS KITCHEN AND COOKING TIMER TEMPERATURE UNIT SELECTOR BUTTON MAIN POWER CONTROL FRAME Fig. G CLEANING To help ensure that the KENYON cooktop stays clean, follow these easy-care tips: Lock the cooktop before cleaning by swiping from the LOCK to the UNLOCK position or touch and hold the LOCK button for 3 seconds. Always remove food spills, grease spatters and metal rub-off from cookware. A razor blade scraper or the equivalent works well to remove spillovers.
ERROR CODE READOUT In the event that the SilKEN® 2 Induction Cooktop is not operating correctly, the control readout will display an error code that will identify the problem. If an error code is shown on the display, identify the code in the SilkEN® 2 Induction Cooktop Troubleshooting Index below and take action as noted. De-power and re-start the unit to clear the display. Allow the unit to cool as necessary.
Warranty Kenyon International, Inc (the “Company”) warrants its products in normal usage to be free of defects in materials and workmanship subject to the conditions and limitations below. Any part, which proves to be defective in normal usage during the warranty period will be repaired or replaced by the Company. This warranty covers certain products built by the Company and is subject to the following conditions and limitations: 1.
