Manual

ManualsBrandsKeri Systems ManualsSensorsMS-3000

MS-3000 MicroStar Reader

2305 Bering Drive 01815-001 Rev. H

San Jose, CA 95131 USA

(800) 260-5265 (408) 435-8400 FAX (408) 577-1792

Web: www.kerisys.com E-mail: sales@kerisys.com Page 1 of 8

MS-3000Quick Start Guide

The MS-3000 MicroStar Reader

The MS-3000 MicroStar Reader is intended for installation on a window mullion or a door frame,

on or off metal, in proximity applications where an unobtrusive reader is required. The reader

provides an audible beeper and a multi colored LED to annunciate the reader's status when used

with a PXL-250, PXL-100, or IntelliProx.

• Amber - to indicate normal operation awaiting an access event

• Green - to indicate a valid card has been presented or the door has been unlocked for access

• Red - to indicate an invalid card has been presented or the door is in an alarm condition

The MS-3000 MicroStar Reader is housed in a black, weatherproof, shock resistant package. The

reader provides optimum performance when mounted on aluminum; read range is slightly reduced

if the reader is not mounted on aluminum.

1.0 Specifications

1.1 Dimensions

• 3.25 inches High x 1.41 inches Wide x 0.375 inches Deep

• 8.26 cm High x 3.95 cm Wide x 0.96 cm Deep

Figure 1: MS–3000 Dimensions

Summary of content (8 pages)

PAGE 1
MS-3000 MicroStar Reader The MS-3000 MicroStar Reader is intended for installation on a window mullion or a door frame, on or off metal, in proximity applications where an unobtrusive reader is required. The reader provides an audible beeper and a multi colored LED to annunciate the reader's status when used with a PXL-250, PXL-100, or IntelliProx.
PAGE 2
Quick Start Guide MS-3000 MicroStar Reader 1.2 • 5v to 14v DC @ 50 ma 1.3 • Operating Voltage Cable Specifications up to 500 feet using six conductor, shielded, stranded AWG 24 wire (such as Belden 9536) 2.0 Mounting Instructions Three holes need to be drilled to mount the MicroStar Reader (see Figure 1). One large hole (0.875" - 7/8") accommodates the beeper and the reader cable.
PAGE 3
MS-3000 MicroStar Reader PXL-250 Connections The "A" reader connects to TB5, pins 1 through 6 (TB5 has a seventh pin, but no connection is made to that pin). The "B" reader connects to TB6, pins 1 through 6 (TB6 has a seventh pin, but no connection is made to that pin). Connecting to the PXL-250 – TB5 or TB6 Pin # Function Wire Color 1 2 3 4 4 5 6 7 Reader Antenna Beeper Reader Power Reader Ground Shield Green LED Red LED no connection Blue Green Red Black Silver Brown White – Quick Start Guide 3.
PAGE 4
3.2 Design 5 PXL-100 Connections The "A" reader connects to TB2, pins 14 through 19. The "B" reader to TB3, pins 20 through 25.
PAGE 5
MS-3000 MicroStar Reader IntelliProx Connections The reader connects to TB1, pins 1 through 6. Connecting to the IntelliProx – TB1 Pin # Function Wire Color 1 2 3 4 5 6 6 Reader Antenna Beeper Green LED Red LED Reader Power Reader Ground Shield Blue Green Brown White Red Black Silver Quick Start Guide 3.3 MS-3000 Figure 4: IntelliProx Connections 2305 Bering Drive San Jose, CA 95131 USA (800) 260-5265 (408) 435-8400 FAX (408) 577-1792 Web: www.kerisys.com E-mail: sales@kerisys.com 01815-001 Rev.
PAGE 6
Quick Start Guide MS-3000 MicroStar Reader 4.0 Installation Verification The following information applies to an installation with a Keri Systems controller or IntelliProx unit. When used with an alternative host controller/alarm panel through an IntelliProx used in its Wiegand input device mode, the actions of the reader's LED and beeper are controlled by the alternative host controller/alarm panel and might not match those of a Keri Systems controller.
PAGE 7
MS-3000 MicroStar Reader Troubleshooting the Reader Installation Problem The reader does not recognize a card/tag (no beep, no LED flash). Probable Cause 1. One or more of the reader's wiring connections are incorrect. Corrective Action • 2. The reader is not • receiving proper power from the controller. 3. The reader is mounted • too close to a device that radiates electromagnetic interference. 4. A jumper is not set correctly on the controller.
PAGE 8
MS-3000 Quick Start Guide MS-3000 MicroStar Reader Problem Probable Cause 5. You are using an incorrect type of card. 6. The reader is unable to read the card. The reader has a 1. The reader's controller short read range. is not properly grounded. Corrective Action • • • 2. The shield wire for the • reader's cable has opened somewhere between the reader and the controller. 3. The reader is mounted • too close to a device that radiates electromagnetic interference. 4.