User Guide

ManualsBrandsKeri Systems ManualsElectronicsMicroStar Door Frame and Mullion Reader

Table Of Contents

MS-3000 MicroStar Reader

Unit 17 Park Farm Industrial Estate 01815-001 Rev. H

Buntingford, Herts SG9 9AZ UK

TEL: + 44 (0) 1763 273 243 FAX: + 44 (0) 1763 274 106

Web: www.kerisys.com E-mail: sales@kerisystems.co.uk

Page 1 of 8

MS-3000Quick Start Guide

The MS-3000 MicroStar Reader

The MS-3000 MicroStar Reader is intended for installation on a window mullion or a door

frame, on or off metal, in proximity applications where an unobtrusive reader is required. The

reader provides an audible beeper and a multi colored LED to annunciate the reader's status

when used with a PXL-250, PXL-100, or IntelliProx.

• Amber - to indicate normal operation awaiting an access event

• Green - to indicate a valid card has been presented or the door has been unlocked for access

• Red - to indicate an invalid card has been presented or the door is in an alarm condition

The MS-3000 MicroStar Reader is housed in a black, weatherproof, shock resistant package.

The reader provides optimum performance when mounted on aluminum; read range is slightly

reduced if the reader is not mounted on aluminum.

1.0 Specifications

1.1 Dimensions

• 3.25 inches High x 1.41 inches Wide x 0.375 inches Deep

• 8.26 cm High x 3.95 cm Wide x 0.96 cm Deep

Figure 1: MS–3000 Dimensions

Summary of content (8 pages)

PAGE 1
MS-3000 MicroStar Reader The MS-3000 MicroStar Reader is intended for installation on a window mullion or a door frame, on or off metal, in proximity applications where an unobtrusive reader is required. The reader provides an audible beeper and a multi colored LED to annunciate the reader's status when used with a PXL-250, PXL-100, or IntelliProx.
PAGE 2
1.2 • 5v to 14v DC @ 50 ma 1.3 • Operating Voltage Cable Specifications up to 500 feet using six conductor, shielded, stranded AWG 24 wire (such as Belden 9536) 2.0 Mounting Instructions Three holes need to be drilled to mount the MicroStar Reader (see Figure 1). One large hole (0.875" - 7/8") accommodates the beeper and the reader cable. Two small holes are for mounting the reader on the mullion or door frame (hole size is dependent upon the size of the mounting screw).
PAGE 3
MS-3000 MicroStar Reader Connections The MicroStar Reader does not require configuration; there are no switches or jumpers to set. The MicroStar Reader is normally connected to a PXL-250, PXL-100, or IntelliProx, but can be connected to an alternative host controller/alarm panel through an IntelliProx used in its Wiegand input device mode. All connections needed to support the reader are made through the reader's cable. Please consult the tables on pages 2 and 3 for specific connection instructions. 3.
PAGE 4
MS-3000 Quick Start Guide MS-3000 MicroStar Reader 3.2 Design 5 PXL-100 Connections The "A" reader connects to TB2, pins 14 through 19. The "B" reader to TB3, pins 20 through 25.
PAGE 5
MS-3000 MicroStar Reader IntelliProx Connections The reader connects to TB1, pins 1 through 6. Connecting to the IntelliProx – TB1 Pin # Function Wire Color 1 2 3 4 5 6 6 Reader Antenna Beeper Green LED Red LED Reader Power Reader Ground Shield Blue Green Brown White Red Black Silver Quick Start Guide 3.3 Figure 4: IntelliProx Connections MS-3000 Unit 17 Park Farm Industrial Estate Buntingford, Herts SG9 9AZ UK TEL: + 44 (0) 1763 273 243 FAX: + 44 (0) 1763 274 106 Web: www.kerisys.
PAGE 6
Quick Start Guide MS-3000 MicroStar Reader 4.0 Installation Verification The following information applies to an installation with a Keri Systems controller or IntelliProx unit. When used with an alternative host controller/alarm panel through an IntelliProx used in its Wiegand input device mode, the actions of the reader's LED and beeper are controlled by the alternative host controller/alarm panel and might not match those of a Keri Systems controller.
PAGE 7
MS-3000 MicroStar Reader Troubleshooting the Reader Installation Problem The reader does not recognize a card/tag (no beep, no LED flash). Probable Cause 1. One or more of the reader's wiring connections are incorrect. Corrective Action • 2. The reader is not • receiving proper power from the controller. 3. The reader is • mounted too close to a device that radiates electromagnetic interference. 4. A jumper is not set • correctly on the controller.
PAGE 8
MS-3000 Quick Start Guide MS-3000 MicroStar Reader Problem Probable Cause The reader has a 1. The reader's short read range. controller is not properly grounded. 2. The shield wire for the reader's cable has opened somewhere between the reader and the controller. 3. The reader is mounted too close to a device that radiates electromagnetic interference. 4. The controller is mounted too close to a device that radiates electromagnetic interference. 5. The reader is powered by a switching power supply.