Owner manual

ManualsBrandsKeri Systems ManualsSensorsMS-4000

MS-4000: ShootingStar Reader

2305 Bering Drive 01815-004 Rev. G

San Jose, CA 95131 USA

(800) 260-5265 (408) 435-8400 FAX (408) 577-1792

Web: www.kerisys.com E-mail: sales@kerisys.com Page 1 of 8

MS-4000Quick Start Guide

The MS-4000 ShootingStar Reader

The MS-4000 ShootingStar Reader is intended for installation on a solid metal surface, in proximity

applications where a vandal-proof reader is required. The reader is housed in a weatherproof,

bulletproof stainless steel package.

1.0 Specifications

1.1 Dimensions

• 5.25 inches High x 2.00 inches Wide x 0.75 inches Deep

• 13.35 cm High x 5.08 cm Wide x 1.91 cm Deep

Figure 1: MS-4000 Dimensions

Summary of content (8 pages)

PAGE 1
MS-4000: ShootingStar Reader The MS-4000 ShootingStar Reader is intended for installation on a solid metal surface, in proximity applications where a vandal-proof reader is required. The reader is housed in a weatherproof, bulletproof stainless steel package. 1.0 Specifications 1.1 Dimensions • • 5.25 inches High x 2.00 inches Wide x 0.75 inches Deep 13.35 cm High x 5.08 cm Wide x 1.
PAGE 2
Quick Start Guide MS-4000: ShootingStar Reader 1.2 • 5v to 14v DC @ 50 ma 1.3 • Operating Voltage Cable Specifications up to 500 feet using six conductor, shielded, stranded AWG 24 wire (such as Belden 9536) 2.0 Mounting Instructions There are two methods for mounting the ShootingStar Reader on a solid metal surface (see Figure 1 on page 1). 1. To mount the reader from the outside, three holes need to be drilled. One through-hole (0.25" – 1/4") accommodates the reader cable.
PAGE 3
MS-4000: ShootingStar Reader PXL-250 Connections The "A" reader connects to TB5, pins 1, 3 and 4 (no connection is made to pins 2, 5, 6, and 7). The "B" reader connects to TB6 pins 1, 3 and 4 (no connection is made to pins 2, 5, 6, and 7). Connecting to the PXL-250 – TB5 or TB6 Pin # Function Wire Color 1 2 3 4 4 5 6 7 Reader Antenna no connection Reader Power Reader Ground Shield no connection no connection no connection Blue – Red Black Silver – – – Quick Start Guide 3.
PAGE 4
3.2 Design 5 PXL-100 Connections The "A" reader connects to TB2, pins 14 through 19. The "B" reader connects to TB3, pins 20 through 25.
PAGE 5
MS-4000: ShootingStar Reader IntelliProx Connections The reader is connected to TB1, pins 1, 5, and 6 (no connection is made to pins 2, 3, and 4). Connecting to the IntelliProx – TB1 Pin # Function Wire Color 1 2 3 4 5 6 6 Reader Antenna no connection no connection no connection Reader Power Reader Ground Shield Blue – – – Red Black Silver Quick Start Guide 3.
PAGE 6
4.0 Installation Verification The following information applies to an installation with a Keri Systems controller or IntelliProx unit. When used with an alternative host controller/alarm panel through an IntelliProx used in its Wiegand input device mode, the actions of the reader are controlled by the alternative host controller/alarm panel and might not match those of a Keri Systems controller.
PAGE 7
MS-4000: ShootingStar Reader Troubleshooting the Reader Installation Problem The reader does not recognize a card/tag. Probable Cause 1. One or more of the reader’s wiring connections are incorrect. Corrective Action • 2. The reader is not • receiving proper power from the controller. 3. The reader is mounted • too close to a device that radiates electromagnetic interference. 4. A jumper is not set correctly on the controller.
PAGE 8
MS-4000 Quick Start Guide MS-4000: ShootingStar Reader Problem Probable Cause 5. You are using an incorrect type of card. 6. The reader is unable to read the card. The reader has a 1. The reader's controller short read range. is not properly grounded. Corrective Action • • • 2. The shield wire for the • reader's cable has opened somewhere between the reader and the controller. 3. The reader is mounted • too close to a device that radiates electromagnetic interference. 4.