Manual

ManualsBrandsKeri Systems ManualsSensorsMS-5000

MS-5000 MiniStar Reader

2305 Bering Drive 01815-002 Rev. G

San Jose, CA 95131 USA

(800) 260-5265 (408) 435-8400 FAX (408) 577-1792

Web: www.kerisys.com E-mail: sales@kerisys.com Page 1 of 8

MS-5000Quick Start Guide

The MS-5000 MiniStar Reader

The MS-5000 MiniStar Reader is intended for installation in a single gang electrical "J-Box," in

proximity applications where an unobtrusive reader is required. It can also be mounted directly onto

nonmetallic walls. The reader provides an audible beeper and a multi colored LED to annunciate

the reader's status when used with a PXL-250, PXL-100, or IntelliProx.

• Amber - to indicate normal operation awaiting an access event

• Green - to indicate a valid card has been presented or the door has been unlocked for access

• Red - to indicate an invalid card has been presented or the door is in an alarm condition

The MS-5000 MiniStar Reader is housed in a black or white, weatherproof, shock resistant

package. The reader provides optimum performance when mounted at least one inch away from

metal surfaces; read range is reduced if the reader is mounted on or near metal surfaces.

1.0 Specifications

1.1 Dimensions

• 4.38 inches High x 3.00 inches Wide x 0.375 inches Deep

• 11.13 cm High x 7.62 cm Wide x 0.96 cm Deep

Figure 1: MS-5000 Dimensions

Summary of content (8 pages)

PAGE 1
MS-5000 MiniStar Reader The MS-5000 MiniStar Reader is intended for installation in a single gang electrical "J-Box," in proximity applications where an unobtrusive reader is required. It can also be mounted directly onto nonmetallic walls. The reader provides an audible beeper and a multi colored LED to annunciate the reader's status when used with a PXL-250, PXL-100, or IntelliProx.
PAGE 2
Quick Start Guide MS-5000 MiniStar Reader 1.2 • 5v to 14v DC @ 100 ma 1.3 • Operating Voltage Cable Specifications up to 500 feet using six conductor, shielded, stranded AWG 24 wire (such as Belden 9536) 2.0 Mounting Instructions 2.1 Wall Mounting Three holes need to be drilled to mount the MiniStar Reader (see Figure 1). One large hole (0.875" – 7/8") accommodates the beeper and the reader cable.
PAGE 3
MS-5000 MiniStar Reader PXL-250 Connections The "A" reader connects to TB5, pins 1 through 6 (TB5 has a seventh pin, but no connection is made to that pin). The "B" reader connects to TB6, pins 1 through 6 (TB6 has a seventh pin, but no connection is made to that pin). Connecting to the PXL-250 – TB5 or TB6 Pin # Function Wire Color 1 2 3 4 4 Reader Antenna Beeper Reader Power Reader Ground Shield Blue Green Red Black Silver 5 6 7 Green LED Red LED no connection Brown White – Quick Start Guide 3.
PAGE 4
3.2 Design 5 PXL-100 Connections The "A" reader connects to TB2, pins 14 through 19. The "B" reader to TB3, pins 20 through 25.
PAGE 5
MS-5000 MiniStar Reader IntelliProx Connections The reader is connected to TB1, pins 1 through 6. Connecting to the IntelliProx – TB1 Pin # Function Wire Color 1 2 3 4 5 6 6 Reader Antenna Beeper Greeen LED Red LED Reader Power Reader Ground Shield Blue Green Brown White Red Black Silver Quick Start Guide 3.3 MS-5000 Figure 4: IntelliProx Connections 2305 Bering Drive San Jose, CA 95131 USA (800) 260-5265 (408) 435-8400 FAX (408) 577-1792 Web: www.kerisys.com E-mail: sales@kerisys.
PAGE 6
Quick Start Guide MS-5000 MiniStar Reader 4.0 Installation Verification The following information applies to an installation with a Keri Systems controller or IntelliProx unit. When used with an alternative host controller/alarm panel through an IntelliProx used in its Wiegand input device mode, the actions of the reader's LED and beeper are controlled by the alternative host controller/alarm panel and might not match those of a Keri Systems controller.
PAGE 7
MS-5000 MiniStar Reader Troubleshooting the Reader Installation Problem The reader does not recognize a card/tag (no beep, no LED flash). Probable Cause 1. One or more of the reader's wiring connections are incorrect. Corrective Action • 2. The reader is not • receiving proper power from the controller. 3. The reader is mounted • too close to a device that radiates electromagnetic interference. 4. A jumper is not set correctly on the controller.
PAGE 8
Quick Start Guide MS-5000 MiniStar Reader Problem Probable Cause Corrective Action 5. You are using an incorrect type of card. 6. The reader is unable to read the card. The reader has a 1. The reader's controller short read range. is not properly grounded. • 2. The shield wire for the reader's cable has opened somewhere between the reader and the controller. 3. The reader is mounted too close to a metallic object. • • • • MS-5000 4.