Manual
Page 5
01816-100 Rev. E
1530 Old Oakland Rd., Ste 100 San Jose, CA 95112 U.S.A. (800)260-5265 (408)451-2520 Fax (408)441-0309
.
PXL-100:SMART ENTRY CONTROLLER
8) Trouble Shooting a PXL-100
7) PXL-100 Installation Verification
When operating correctly, a PXL-100 will store and process card information, store transactions for
door operations and accept inputs from either a hand held programmer or a PC. To verify that the
controller is working correctly, present a card to the reader. If the card has not yet been enrolled,
the reader will beep once. Verify that the unit is working correctly by enrolling a card with the Keri
Systems HPP-100 or the TAP-100 software.
Enroll it in Time Zone 0 (also known as level 0).
Consult the operation manuals for the products for instructions on how to enroll a card. Present the
newly enrolled card and listen for a double beep from the reader. This indicates that the card has
been successfully stored in memory. Wait five seconds and present the card again. Listen for the
click made by the relay controlling the door lock. In noisy environments it may be necessary to
place your finger on it to verify that it has actuated. Consult the trouble shooting guide below if the
system does not respond as expected. Additional help may be obtained from the diagnostics guide
beginning on page 8 of this document.
Problem Probable Cause Corrective Action
The PXL-100 does not
p
ower u
p
.
I.E. there is no dis
p
la
y
on the LCD
screen.
1
)
No
p
ower in
p
ut
a
pp
lied
,
or inade
q
uate
p
ower a
pp
lied.
Check main
p
ower circuit breaker.
Measure volta
g
e in
p
ut at POWER
TERMINAL 12VAC at Pins 4 and 5
+/- 20%
,
or 12VDC at
p
ins 2
(
-
)
and 3
(
+
)
+/- 2 volts.
2
)
Wired incorrectl
y
. AC must be connected to Pins 4 and
5 of INPUT POWER TERMINAL.
DC must be connected to Pins 2
(
+
)
and 3
(
-
)
of INPUT POWER
TERMINAL
Reader does not bee
p
or reader
LED does not flash when
p
resentin
g
a card
1
)
Reader is not
p
lu
gg
ed into the
ANTENNA Terminal.
Check to see that the Reader is
p
lu
gg
ed into the terminal
p
ro
p
erl
y
---a
p
in is not sli
pp
ed.
Or
,
Controller kee
p
s resettin
g
.2
)
Reader is wired
incorrectl
y
.
LED lead
(
BRN
)
must be connected
to
p
in 1 of ANTENNA TERMINAL
,
BEEP lead
(
GRN
)
must be connected
to
p
in 2
,
(
RED
)
lead to
p
in 3
,
(
BLK
)
to
p
in 4 and
(
BLU
)
lead to
p
in 5.
Check to ensure wire is makin
g
contact with the connector---
connector contact is not crim
p
ed on
wire insulation.
3
)
Reader
p
ower is
insufficient.
Measure reader volta
g
e at ANTENNA
TERMINAL
p
in 3
(
+
)
and
p
in 4
(
GND
)
. Ensure 12volts +/- 2 volts is
measured at the reader
,
usin
g
Belden 24# wire or lar
g
er
,
reader
distance must be less than 500 feet.
With Reader connected
,
usin
g
the
HPP-100
p
ro
g
rammer
,
PXL-100
controller will not acce
p
t default PIN
(
0000
)
1
)
PIN has been
chan
g
ed.
Reset PIN to default value b
y
removin
g
p
ower and rea
pp
l
y
in
g
p
ower with the S1 button on the main
board de
p
ressed. Hold the button
down until a double bee
p
is
p
roduced
b
y
the reader.