Manual

Page 8
01816-100 Rev. E
1530 Old Oakland Rd., Ste 100 San Jose, CA 95112 U.S.A. [phone] [phone] Fax [phone]
.
PXL-100:SMART ENTRY CONTROLLER
8) Trouble Shooting a PXL-100 (continued)
Lock Rela
y
C
y
cles on and off
continuousl
y
.
1
)
Prom is not seated
p
ro
p
erl
y
Visuall
y
ins
p
ect the E-Prom labeled
and located on the ri
g
ht side of the
PXL-100 above the lithium batter
y,
to ensure all
p
ins are seated
p
ro
p
erl
y
in the Prom socket
TAP-100 Software will not boot. 1
)
PC does not have
enou
g
h conventional
memor
y
.
Must have 560K b
y
tes available
of conventional memor
y
. Refer to
DOS manual memor
y
mana
g
er
for instructions maximizin
g
available free memor
y
.
PC will not communicate with
network.
1
)
Cable is wron
g
. Review the Installation Manual
,
Fi
g
ure 4. Pro
p
er cable for a PC
9
p
in serial in
p
ut is Model KDP-
105. Cable for a PC 25
p
in serial
in
p
ut is Model KDP-104
(
since
both ends or the cable are
sockets
,
‘
p
olarit
y
’
must be
observed
)
. KDP-104 cable is
labeled indicatin
g
direction..
2
)
Com
p
uter is not
confi
g
ured to
communicate
throu
g
h the
p
ro
p
er
serial
p
ort.
Usin
g
the TAP-100 software
,
select
[
Setu
p]
from the main
menu. In the Setu
p
submenu
,
select
Port Assi
g
nments
.
Assi
g
n the correct
p
ort and
[
ENTER
]
The Prox
p
ort must
indicate the PC
p
ort in which the
cable is connected.
3
)
PXL-100 serial
connector is not
confi
g
ured to
communicate with
the PC.
Set the PXL-100 serial
p
ort to PC
confi
g
uration b
y
a
pp
l
y
in
g
p
ower
with the reset button on the main
board de
p
ressed for 10 seconds
or until the reader
p
roduces a
double bee
p
. This reset
p
rocedure will also reset the PIN.
This reset will not affect other
p
ro
g
rammed data.
PC will not communicate with
network via a Modem.
1
)
Wron
g
t
yp
e of
modem
Must be Ha
y
es com
p
atible with
baud rate of at least 9600
2
)
PXL-100 is not
confi
g
ured to
communicate with
the modem.
Usin
g
HPP-100
,
confi
g
ure the
PXL-100 serial
p
ort for remote.
[
Level
]
9 2 2
[
SEND
]
Some PXL-100’s within the
network are not communicatin
g
with the PC.
1
)
Address Clash. Check the address di
p
switch
settin
g
on each controller o
p
tion
board.
2
)
Corru
p
ted RAM in
one or more of the
controllers.
In the
Utilities
menu
,
enter the
Network
sub-menu. Examine the
network information and note the
Res
p
ondin
g
PXL-100’s number.
On earl
y
models this number is
Hexadecimal. Reset the fault
y
PXL100/s