KERN & Sohn GmbH Ziegelei 1 D-72336 Balingen E-Mail: info@kern-sohn.com Phone: +49-[0]7433- 9933-0 Fax: +49-[0]7433-9933-149 Internet: www.kern-sohn.com Operating and Installation Instructions Display Unit KERN KXS/KXG-TM Version 2.
GB KERN KXS/KXG-TM Version 2.0 11/2014 Operating and installation instructions Display unit Contents 1 Technical data ................................................................................................... 5 2 Appliance overview ........................................................................................... 6 2.1 Keyboard overview .................................................................................................... 7 2.1.1 2.1.2 2.2 3 3.1 3.2 3.3 3.4 4 4.1 4.
7 7.1 7.2 7.3 7.4 7.5 7.6 Basic Operation ............................................................................................... 18 Start-up .....................................................................................................................18 Switching Off ............................................................................................................18 Zeroing ............................................................................................................
14 Data output format ....................................................................................... 70 14.1 14.2 7-digit data format (first decimal place not included) .................................................70 6-digit data format (first decimal place not included) .................................................70 15 16 Bluetooth (Factory option) .......................................................................... 71 Servicing, maintenance, disposal ..........................
1 Technical data KERN KXS-TM Display Solution verifiable KXG-TM 6-digit Single (Max.) 10,000 e Dual (Max.) 5,000 e Resolution non-verifiable 30,000 d Verification class III Weighing ranges Max. 2 Weighing Units g, kg Divisions Display 1,2,5,…10, n LCD 55 mm digits with back lighting Max. 8 x 350 Ω DMS weighing cells Electric Supply Input voltage 110-230 V AC Built-in power supply unit 6 V, 4.
2 Appliance overview 1 2 3 4 5 6 7 8 9 6 Wireless Status of rechargeable battery Wall bracket Locking screw Display Keyboard Electric Supply RS 232 / RS485 (Factory option) Connection to the load cell KXS/KXG-TM-BA_IA-e-1420
2.1 Keyboard overview 2.1.1 Models KXS-TM: Button Description ON/OFF button Function 1. Turn on/off • Functional button (allocation see chap. 10.1 FNC-03) • Gross weight switch over to net weight • Weighing unit • • Taring Confirm entry • Zeroing • Functional button (allocation see chap. 10.
2.1.1.1 Navigation keys and their function in the menu 2.1.2 • • Increase flashing digit Scroll forward in menu • • Decrease flashing digit Scroll backwards in menu • • Digit selection to the right Take over selected setting Digit selection to the left Models KXG-TM: Button Description ON/OFF button F-key 8 Function • Turn on/off • Functional button (allocation see chap. 10.
BG/ NET key UNIT-key TARE button ZERO key M+/ PRINT key • Gross weight switch over to net weight • Weighing unit • • Taring Confirm entry • Zeroing • Functional button (allocation see chap. 10.1 FNC-02) 2.1.2.
2.
Non verified weighing systems: Indicator [] next to symbol displays: 1 that the weight value is stable GROSS 2 that the displayed weighing value is a gross weight value 3 that the balance is set to unit counting mode PRETARE HOLD M+ 4 that a PRE-TARE value is stored 5 that the indicated weight value is held in the display, until it is deleted. 6 that data are stored in an accumulative memory 7 That the current selected unit of weight is „oz“.
3 Basic Information (General) 3.1 Proper use The display unit acquired by you is used in combination with a load cell and serves to determine the weighing value of material to be weighed. It is intended to be used as a “non-automatic weighing system”, i.e. the material to be weighed is manually and carefully placed in the centre of the weighing plate. As soon as a stable weighing value is reached the weighing value can be read. 3.2 Improper Use Do not use weighing system for dynamic weighing.
3.4 Monitoring of Test Resources In the framework of quality assurance the measuring-related properties of the display unit and, if applicable, the testing weight, must be checked regularly. The responsible user must define a suitable interval as well as type and scope of this test. Information is available on KERN’s home page (www.kern-sohn.com with regard to the monitoring of display units’ test substances and the test weights required for this.
6 Unpacking and placing 6.1 Installation Site, Location of Use The display units are designed in a way that reliable weighing results are achieved in common conditions of use. Precise and fast work is achieved by selecting the right place for your display unit and your weighing plate.
6.4 Transport Securing Remove the transportation safety device at the four marked positions: Transport Securing 6.5 Placing Mount the display unit in a way that facilitates operation and where it is easy to see. In order to raise the display, the display device can be mounted on an optional stand. 6.6 Mains connection Power is supplied via the external power supply unit. Insert the mains plug into the wall socket. Once connected, the instrument performs a self check.
6.8 Adjustment As the acceleration value due to gravity is not the same at every location on earth, each display unit with connected weighing plate must be coordinated - in compliance with the underlying physical weighing principle - to the existing acceleration due to gravity at its place of location (only if the weighing system has not already been adjusted to the location in the factory).
Sealing: KXS/KXG-TM-BA_IA-e-1420 17
7 Basic Operation 7.1 Start-up Press on/ off key, the equipment completes a self check. As soon as the weight display appears, the instrument will be ready to weigh. 7.2 Switching Off Press the on/ off key approx. 3 seconds, the display will turn off. 7.3 Zeroing Resetting to zero corrects the influence of light soiling on the weighing plate. Manual To unload the weighing system Press the ZERO button, the zero display and the indicator will appear.
7.5 Switch-over weighing unit Press the UNIT-key The weight gauge changes between „kg“and "g". 7.6 Weighing with tare After taring no numeric input of a tare weight can follow. After the numeric input of a tare weight, the system can only be tared if „tare weight > PRE TARE value“ 7.6.1 Taring Deposit weighing vessel. Wait for stability display, then press the TARE button Zero display and indicator net appear. The weight of the container is now internally saved.
7.6.3 Numerical input of tare (PRE-TARE) The known dead weight of a weighing container can be tared off by entering its weight as pre-tare deduction in order to ensure the net weight of the goods to be weighed in subsequent weighings is always displayed. Press the TARE- key, the active position flashes. Enter the known tare weight, e.g. 2 kg and acknowledge with TARE button. Numerical input, see chap. 2.1.1. The entered weight will be stored as tare weight and displayed with negative sign.
8 Applications: 8.1 Parts counting Before the balance can count parts, it must know the average part weight (i.e. reference). Proceed by putting on a certain number of the parts to be counted. The balance determines the total weight and divides it by the number of parts, the socalled reference quantity. Counting is then carried out on the basis of the calculated average piece weight. As a rule: The higher the reference quantity the higher the counting exactness. Determine the unit weight and count 1.
Switch between number of items and weight With the UNIT key you can switch between number of items and weight: By switching the scale off and then on again the scale starts in the unit counting mode. The current reference weight remains stored until the reference is set again or the power supply is interrupted. The counting function is not active, if the weight is under 20d or if below the minimum piece weight (< 0.2 D) is reached.
8.2 Totalization Required settings in the menu: 1. Function „rSi 04“: Setting „M_Plus“, see chapter 12.4 2. Function „rSi 03“, setting F_M 10 or F_M11 (sample print-out see following overview, see chapter 12.3. F_M 10 (M+ accumulating mode 1): F_M 11 (M+ accumulating mode 2): Total = sum of net weight of each weight reading Total = Sum of gross weight of each weight reading Printout example (KERN YKB-01N) Printout example (KERN YKB-01N) 1. Weighing 1. Weighing 2. Weighing 2.
Add up: Place weighing good A, e.g. 5 kg. Wait for stability, then press M + / PRINT key. . The weight is added to the accumulative memory and printed if an optional printer is connected. The number of weighings, followed by the total weight will be indicated. The indicator above M+ shows. Remove the weighed good. More weighed goods can only be added when the display ≤ zero.
Place goods to be weighed, e.g. 7 kg. Wait for stability then press the M+/PRINT, it calculates. The weight value is added to the accumulative memory and given out when connecting an optional printer. Number of weighings, followed by the total weight will be displayed for 2 sec. Then the current weight value appears, the indicator above M + appears. Add more weighed goods as described before. Please note that the weighing system must be unloaded between the individual weighing procedures.
Display and output sum „Total“: When the scale is unloaded (zero indicator) press the M+/PRINT key, the number of weight readings followed by the total weight are indicated for 2 seconds. Press M+/PRINT to print out this display. Delete accumulative memory: 1. With M+/PRINT : At the display “Number of weighings” press M+/PRINT key again. The data in the accumulative memory are deleted. The indicator above M+ turns off. 2.
9 Menu The menu consists of the following blocks: Settings of the display device External adjustment Settings of the interface Exit menu / back to weighing mode. Access to menu: In the weighing mode press the BG/NET and ZERO key simultaneously, "01 FnC" is indicated.
10 Indicator settings (menu block "01 FnC") Access to menu: In the weighing mode press BG/ NET and ZERO key simultaneously "01 FnC" is indicated, see chapter 9.
Exit menu / back to weighing mode: Leave the example function "FnC 01" Select with the navigation keys "FNC 00” and confirm with TARE key.
Overview: FnC 00 Exit menu FnC 01 Display background illumination FnC 02 Automatic power switch-off FnC 03 Weighing with tolerance range / set limit values FnC 04 Reset to default setting FnC 05 Automatic zero tracking / stability and response settings FnC 06 Data-Hold function FnC 07 Automatic reference optimization with counting of items FnC 08 Not documented FnC 09 Not documented FnC 10 Automatic saving of zero point (not available in the case of weighing systems with type approval).
10.1 Backlighting of the display (function "FnC 01") Call up function "FnC 01", see chapter 10 „Navigation in the menu“. Press the TARE-key , the current setting for the back lighting of the display is indicated. Select desired settings with TARE or UNIT key. bl off Display background illumination off bl on Starting from a weight > 10 d the back lighting of the display is switched on automatically.
10.2 Automatic power cut "Auto power off (function „FnC 02“) Call up function "FnC 02", see chapter 10 "Navigation in the menu”. Press the TARE-key, current setting appears. Select desired settings with TARE or UNIT key. A off0 Function switched off A off1 The indicator is switched off automatically within the adjusted time, if the weighing system is not used and/ or the weight < 10 D. Selectable between 1 - 9 minutes. A off9 Confirm with the TARE key, the display returns back to the menu.
10.3 Weighing with tolerance range (function "FnC 03 „) You can set an upper or lower tolerance limit when weighing with tolerance range and thus ensure that the weighed load remains exactly within the set tolerance limits. Tolerance checks such as dosing, portioning and sorting the display above or below the tolerance levels with a visual and acoustic signal (depending on the setting in the menu).
Settings: Call up function "FnC 03", see chapter 10 "Navigation in the menu“. Press the TARE key, the current settings of the upper tolerance is indicated. With the navigation keys (see chapter XX) enter the desired value e.g. 3 kg. Press the TARE key repeatedly until the display for the input of the lower tolerance appears. With the navigation keys (see chapter 2.1.1) Enter the desired value e.g. 2.9 kg.
Press the TARE key until the display for the settings of the audio signal appears. The current setting will be displayed. With the navigation keys (see chapter 2.1.1) select the desired setting.
Weighing with tolerance range: Tare when using a weighing container. Put on goods to be weighed, tolerance control is started. The indicators show whether the load is within the two set tolerance limits. Load below specified tolerance Indicator illuminated Load within specified tolerance Indicator illuminated Load exceeds specified tolerance Indicator illuminated To deactivate the function for the tolerance levels enter the value „00.000 kg“.
10.4 Resetting to factory settings (function "FnC 04 „) The following functions are reset to factory setting with "FnC 04 „. 1. External adjustment weight 2. Settings for weighing with tolerance range 3. Filter settings 4. Settings of number of items Call up function "FnC 04", see chapter 10 "Navigation in the menu“. Press the TARE key. Select desired settings with TARE or UNIT key.
10.5 Automatic zero-adjusting/ stability and response settings (function "FnC 05“) This function is only available for unverified weighing systems (CFn 02 = 0), for verified weighing systems see chapter 18.5.1. Call up function "FnC 05", see chapter 10 "Navigation in the menu“. Press the TARE-key, current setting appears. Select desired settings with TARE or UNIT key. Zero 0 Zero 9 Switch Automatic zero-adjusting switch on and off and select zero range.
FiL 0 FiL 9 The higher the value, the more priority is given to stability. You can select 0-9. Factory setting "0". Confirm with the TARE key, the current response level is displayed. 3 db 0 The higher the value, the more priority is given to response. You can select 0-9. Factory setting "5".
10.6 Data Hold functions (function "FnC 06“) With verified balancing systems (Cfn 02 = 1) the setting „hold = 0“ cannot be altered with the function „FnC 06“ (changes are possible with function "CFn 05" see chapter 18.5.4.). Call up function "FnC 06", see chapter 10 "Navigation in the menu“. Press the TARE-key, current setting appears. Select desired settings with TARE or UNIT key.
Confirm with the TARE key, the display returns back to the menu. Return to weighing mode function, see chap. 10. 10.6.1 Animal weighing function With this function jerky balancing goods can be weighed, e.g. living animals. The scale calculates an average value by the number of adjusted weighings and displays this until the scale is cleared (display < 10d). Settings: Call up setting "hold 4", see. chapter 10.6. Press the TARE-key, current setting appears.
Press the TARE key repeatedly until the current setting "number of weight readings" is indicated. 1 Number of weight readings, which are consulted for the average value calculation, you can select 1, 2, 4, 8, 16, 32, 64. Factory setting "8“ 64 Confirm with the TARE key, the display returns to the menu. Select with the navigation keys "FNC 00” and confirm with TARE key.
From now on the scale is in animal weighing mode. Animal weighing: When the animal weighing function is activated horizontal segments appear at the zero display. Place goods to be weighed on the balance. The scale calculates the average value by the number of adjusted weight readings. The indicator appears above HOLD. For further measurements unload the scale.
Return to weighing mode: In the weighing mode press the BG/NET and ZERO key simultaneously, "01 FnC" is indicated. Press the TARE key, „FNC 00” is indicated. Select „FnC 00“ with the navigation keys and confirm with the TARE key. „hold 4“ is indicated. Select „hold 0“ with the navigation keys and confirm with the TARE key. Confirm with the TARE key, the display returns back to the menu. Select with the navigation keys "FNC 00” and confirm with TARE key.
KXS/KXG-TM-BA_IA-e-1420 45
10.7 Automatic reference optimisation with the unit count (function „FnC 07“) Call up function „FnC 07“, see chapter 10 "Navigation in the menu“. Press the TARE-key, current setting appears. Select desired settings with TARE or UNIT key. AvErG 0 No reference optimisation AvErG 1 Reference optimisation is activated. The device automatically determines the weight per unit again, if the number of parts has increased Confirm with the TARE key, the display returns back to the menu.
10.8 Automatic storage of zero point (function "FnC 10“) This function is only available for unverified weighing systems (CFn 02 = 0). Call up function "FnC 10", see chapter 10 "Navigation in the menu“. Press the TARE-key, current setting appears. Select desired settings with TARE or UNIT key. off Function switched off (factory setting) on If the function is switched on, the last zero point is stored.
10.9 Function of the F-key (function „FnC 12“) Call up function "FnC 12", see chapter 10 "Navigation in the menu“. Press the TARE-key, current setting appears. Select desired settings with TARE or UNIT key. 3 different functions can be assigned to the F-key: MC The accumulative memory is cleared when the F-key is pressed. hr The weight value 10 x higher resolution is displayed when the F key is pressed. t-tP PRE-TARE Confirm with the TARE key, the display returns back to the menu.
10.10 Auto Zero This function is used to tare small variations in weight automatically. In the event that small quantities are removed or added to the material to be weighed, incorrect weighing results can be displayed due to the “stability compensation“. (e.g. slow flow of liquids from a container placed on the balance, evaporating processes). When apportioning involves small variations of weight, it is advisable to switch off this function.
11 External adjustment "Unverified weighing systems „ (menu block "02 EC”) • • Prepare the required adjustment weight. The weight to be used depends on the capacity of the scale. Carry out adjustment as near as possible to the scale’s maximum weight. Info about test weights can be found on the Internet at: http://www.kern-sohn.com. Observe stable environmental conditions. Stabilisation requires a certain warm-up time.
Ensure that there are no objects on the weighing pan. Press the TARE key. The weight value of the required adjustment weight will be displayed. Carefully place the adjusting weight into the centre of the balancing plate and press the TARE key. After successful adjustment, an acoustic signal sounds, the scale will automatically return to the menu. Take away adjustment weight. Cancel the adjustment: Press the BG/ NET key repeatedly, until „PASS“ is indicated.
Return to weighing mode: 52 KXS/KXG-TM-BA_IA-e-1420
12 Settings RS 232 (menu block "03 rS1”) Access to menu: In the weighing mode press the BG/NET and ZERO key simultaneously, "01 FnC" is indicated. Select "03 rS1" with the navigation keys. Call up the navigation in the menu/ function: Press TARE key Select the function with navigation keys (rS1 00 rS1 13) Zurück ins Menü: Select function rbl 00 and confirm with the TARE key.
Keys and their function in the menu: see chap. 10 Exit menu / back to weighing mode: For example to leave function "rS1 01" Select "rS1 00" with the navigation keys and confirm with the TARE key.
Overview: rS1 00 Exit menu rS1 01 Baud rate rS1 02 Parity rS1 03 Output format rS1 04 Output mode rS1 05 Continuous output rate rS1 06 Automatic data output with zero display.
12.1 Baud rate (function "rS1 01“) Call up function "rS1 01", see chapter 12. Press the TARE-key, current setting appears. Select desired settings with TARE or UNIT key. b600 You can select 600/1200/2400/4800/9600 (bit/ second) b19200 Confirm with the TARE key, the display returns back to the menu. To go back into the weighing mode see chapter 12.
12.2 Parity (function "rS1 02“) Call up function "rS1 01", see chapter 12. Press the TARE-key, current setting appears. Select desired settings with TARE or UNIT key. P n81 No parity, 8 bits, 1 stop bit P E71 Even parity 7 bits, 1 stop bit P o71 Odd parity, 7 bits, 1 stop bit Confirm with the TARE key, the display returns back to the menu. To go back into the weighing mode see chapter 12.
12.3 Output format (function "rS1 03“) Call up function "rS1 01", see chapter 12. Press the TARE-key, current setting appears. Select desired settings with TARE or UNIT key. F_M 00 Factory settings Display value with status Sample printout: ST, G + 1.000 kg F_M 01 Gross weight with status F_M 02 Net weight with status F_M 03 Display value without status sample printout: + 1.
F_M 06 Hi /Lo/ OK status + display value without status sample printout: Lo (001) 001+ 2.000 OK (010) 010+ 3.000 Hi (100) 100+ 4.000 F_M 07 Hi /Lo/ OK status + gross weight without status F_M 08 Hi/ Lo/ Ok status + net weight without status F_M 09 Tare weight F_M 10 M+ accumulation mode 1, sample printout see chapter 8.2 Total = sum of net weight of each weight reading F_M 11 M+ accumulation mode 2, sample printout see chapter 8.
12.4 Output format (function „rS1 04“) Call up function "rS1 04", see chapter 12. Press the TARE-key, current setting appears. Select desired settings with TARE or UNIT key. Comand Data output via remote control commands Stream rS-off Continuous output Automatic issue of first stable weighing value Sequence of operations: 1. Place weight, issue of first stable weighing value 2. Renewed output only possible after weight was removed. 3. Place next weight.
12.5 Continuous output rate (function „rS1 05“) Call up function "rS1 05", see chapter 12. Press the TARE-key, current setting appears. Select desired settings with TARE or UNIT key. rPS 1 rPS 16 MAII Data transmission rate 1, 2, 4, 8, 16 times/ second Factory setting rPS 4 Data transmission rate >16 times/ second Confirm with the TARE key, the display returns back to the menu. To go back into the weighing mode see chapter 12.
12.6 Automatic data output with zero display (function "rS1 06“) Call up function "rS1 06", see chapter 12. Press the TARE-key, current setting appears. Select desired settings with TARE or UNIT key. -b 00 -b 99 Range, below which appliance has to go before the scale prints, you can select 0 - 99 division steps. Factory setting "- b05". Confirm with the TARE key, the display returns back to the menu. To go back into the weighing mode see chapter 12.
12.7 Condition for data output (function "rS1 08”) Call up function "rS1 08", see chapter 12. Press the TARE-key, current setting appears. Select desired settings with TARE or UNIT key. Factory setting Output only with stable weight values (no output with unstable weight values and "OL „) StoL-p Output only for stable weight values (including „OL“) ALL-P Output of all weight values Stb-P Confirm with the TARE key, the display returns back to the menu.
12.8 6/ 7-digit data format (function "rS1 09”) Call up function "rS1 09", see chapter 12. Press the TARE-key, current setting appears. Select desired settings with TARE or UNIT key. S iII Factory setting SEvEn 6 Digits 7 Digits Confirm with the TARE key, the display returns back to the menu. To go back into the weighing mode see chapter 12.
12.9 Set the date/ time (function "rS1 10“) Call up function "rS1 09", see chapter 12. Press the TARE-key, current setting appears. Set the date with TARE or UNIT key. Press the TARE key repeatedly until the last digit flashes, the display for the time setting appears. Press the TARE key repeatedly until the last light flashes, the display returns back to the menu. To go back into the weighing mode see chapter 12.
Set the date format (function "rS1 11“) Call up function "rS1 11", see chapter 12. Press the TARE-key, current setting appears. Select desired settings with TARE or UNIT key. y_m_d Year/ month/ day d _m_j Day/Month/Year Confirm with the TARE key, the display returns back to the menu. To go back into the weighing mode see chapter 12.
RS 485 ID input (function "rS1 12“) Call up function "rS1 12", see chapter 12. Press the TARE-key, current setting appears. Select desired settings with TARE or UNIT key. Id 00 ID input, you can select 0 - 99 With the input „ID 00“ the remote control instructions are the same as with RS232, see chapter 13 Id 99 Confirm with the TARE key, the display returns back to the menu. To go back into the weighing mode see chapter 12.
13 Instruction mode RS 485: During input „Id 00“(function RS1 12, see chapter 12.12) the instruction format is the same as with RS232. During input "ID 01-99“ "@ID „must be placed in front of the remote control command, so that the respective scale reacts to the instruction; e. g. to set the scale to zero with ID 99 the instruction must be sent to "@99MZ“ followed by the control characters .
RJ Hi /Lo/ OK status + display value without status Example: Hi/ Lo/ OK status Lo (001) Sample display 001+ 2.000 OK (010) 010+ 3.000 Hi (100) 100+ 4.000 RK Hi/Lo/ OK status + gross weight without status (example see "RJ"). RL RS Rear one/ Lo/ OK status + net weight without status (example see "RJ").
14 Data output format 14.1 7-digit data format (first decimal place not included) Weight value with status Gross S T , G S , + 0 1 2 3 4 5 6 7 SP SP o z Net S T , N T , + 1 . 2 3 . 4 5 6 t l . g Tare S T , T R , + 0 1 2 . 3 4 5 6 SP SP k g Plus OL O L , G S , + SP SP SP SP SP SP SP SP SP SP SP SP Minus OL O L , G S , - SP SP SP SP SP SP SP SP SP SP SP SP Unstable U S , G S , + 0 1 2 3 4 .
15 Bluetooth (Factory option) Click in the task border with activated Bluetooth. Click on „Add device“.
Click on "Enter pairing code of the device" Enter code 1111 72 KXS/KXG-TM-BA_IA-e-1420
Click on „Next“ Click on „Close“ KXS/KXG-TM-BA_IA-e-1420 73
Display Bluetooth network appliance Double click 74 KXS/KXG-TM-BA_IA-e-1420
16 Servicing, maintenance, disposal Before any maintenance, cleaning and repair work disconnect the appliance from the operating voltage. 16.1 Clean Keep IP protection. Clean the stainless-steel parts with a soft cloth soaked with a cleaning agent suitable for stainless steel. For stainless steel parts do not use any cleaning agents which contain sodium hydroxide solution, acetic, hydrochloric, sulphuric or citric acid.
17 Instant help In case of an error in the program process, briefly turn off the display unit and disconnect from power supply. The weighing process must then be restarted from the beginning. Help: Fault The displayed weight does not glow. Possible cause • • • • • The display unit is not switched on. Mains power supply interrupted (mains cable defective). Power supply interrupted. (Rechargeable) batteries are inserted incorrectly or empty No (rechargeable) batteries inserted.
18 Installation display appliance/ load cell Installation / configuration of the weighing system must be carried out by a well acquainted specialist with the workings of weighing balances. 18.1 Weighing system design The display unit is suitable for connection to any analogue platform in compliance with the required specifications. The following data must be established before selecting a weighing cell: • Weighing balance capacity This usually corresponds to the heaviest load to be weighed.
18.2 Attach the load cell Disconnect the display unit from the power supply. Attach the load cell cables according to the following illustration. 4-wire load cells: When using 4-wire load cells SEN + and SEN - must not be connected.
18.
19 Service menu Verified weighing systems: • In verified weighing systems the access to the service menu is locked. In order to unlock the access, the sealing must be destroyed (see chapter 6.9) and the housing opened. On the plate move the adjusting switch SWA1 to position „ADJ”. Switch on equipment, is indicated. LOCK SWA1 • • ADJ After the configuration, the access to the service menu must be locked again. Also move the adjusting switch to the position „LOCK“.
The service menu consists of the following blocks: Configure the weighing system, see chapter 18.1 Adjustment of verified weighing systems, see chapter 18.3 For linearisation see chapter 18.2 Appliance settings of verified weighing systems, see chapter 18.5 Alter the gravitation zone, see chapter 18.
19.1 Configure weighing system / menu block Call up the menu block , see chapter 18. Call up the navigation in the menu/ function: Press TARE key Select function using navigation keys, (CSP 00 CSP 03) Back to menu: Select function "CSP 00" and confirm with the TARE key. Overview: CSP 00 Exit menu CSP 01 Unverified weighing systems, see chapter 18.1.1 CSP 02 For verified weighing systems see chapter 18.1.2 CSP 03 Type of scale, see chapter 18.1.
19.1.1 Unverified weighing systems (function „CSP 01”) Menu setting „unverified” CFN 02 = 0, see chapters. 18.5.2. Call up function "CSP 01", see chapter 18.1 "Navigation in the menu“. Press the TARE key, the current set capacity / resolution is displayed for 2 seconds (display sample Max 15 kg / d 0.01 kg), followed by the display of "u00000" to adjust the weighing units.
Use the navigation buttons to select desired settings Example 020002: Standard weighing unit "kg“ (a), second weighing unit "lb“ (b), number of weighing units "2“ (f) Confirm with TARE key, the display "C00000“ appears on the input capacity (max). Example 015000 ⇒ 15.000kg With the navigation keys (see chapter 2.1.1) enter the desired capacity. Examples: Max. Input 15.000 kg 015000 1500.0 g 015000 6.
Settings: Description (m) ⇒ Readability (d), select from 1, 2, or 5 steps (n) ⇒ Number of decimal places, select from 0 ~ 5 Examples: Adjustment 3 1 3 (o) ⇒ (p) ⇒ 15.000 kg 1500.0 g 6.
Example 132000: 1⇒ Readability 1 step 3⇒ 3 decimal places 2⇒ Divide into maximum of two sections 0⇒ Multi-interval balance 0⇒ Division multiplication factor Press the TARE key, the newly set capacity / resolution is displayed for 2 seconds (display sample maximum 15 kg / d 0.001 kg). The display automatically returns back to the menu. With the navigation keys (see chapter 2.1.1) select "CSP 00". Confirm with TARE key.
19.1.2 Verified balancing systems (function "CSP 02“) For menu settings "verified" CFN 02 = 1, see chapter. 18.5.2. Call up function "CSP 02", see chapter 18.1 "Navigation in the menu“. Press the TARE key, the current set capacity / resolution is displayed for 2 seconds (display sample Max 15 kg / d 0.01 kg), followed by the display of "unit" of the current set weighing units.
Use the navigation buttons to select desired settings Example unit 20: Number of balancing units "2“ (a), standard weighing unit „kg“(b), Confirm with TARE key, the current standard weighing unit is indicated for 2 seconds (e.g. „kg“) followed by the display „000001“ for adjustment to the capacity (max.). Settings maximum: Description (c) ⇒ Standard weighing unit (d-h) ⇒ Capacity (max) (i-n) ⇒ Weight value of adjusting weight With the navigation keys (see chapter 2.1.
Example 015000 ⇒ 15.000kg Confirm with the TARE key, the display "000003" appears for the input of "resolution (d), decimal places and type of scale". Settings: Description (o) ⇒ Readability (d), select from 1, 2, or 5 steps (p) ⇒ Number of decimal places, select from 0 ~ 5 0 0⇒ 0.0 1⇒ 2⇒ 0.00 3⇒ 0.000 4⇒ 0.0000 5⇒ (q) ⇒ 0 (r) ⇒ 0,1 0.00000 Standard weighing unit Always use setting of "0“.
Example 530010: 5⇒ Readability of 5 steps 3⇒ 3 decimal places d = 0.005 0⇒ Standard weighing unit „kg“ 0⇒ Single-range balance 1⇒ Sequence of the weighing units 0⇒ Multi-interval balance Press the TARE key, the newly set capacity / resolution is displayed for 2 seconds (display sample maximum 15 kg / d 0.005kg). The display automatically returns back to the menu. Select „CSP 00“ with the navigation keys. Confirm with TARE key.
19.1.3 Set the buffeting point (function „CSP 03“) With the functions „CSP 01” and „CSP 02” the weighing range, by default, can be divided into: Single-range balance Divide into maximum of two sections (subranges ½ max) Divide into maximum of three sections (subranges 1/6 and 2/3 max) Call up function „CSP 03” to amend the buffeting point. Call up function „CSP 03“, see chapter 18.1 "Navigation in the menu“. Press the TARE key, the display shows "unit 0" to enter the weighing unit.
Confirm with the TARE key, the current set second buffeting point (only during allocation into 3 sections) is indicated. Use the navigation keys to select the desired settings Confirm with the TARE key, the display returns back to the menu. Select „CSP 00“ with the navigation keys. Confirm with TARE key. To exit the menu / return back to the weighing mode, see chapter 18.1.1 and/or 18.1.2.
19.2 Linearization/ menu block Linearity shows the greatest deviation of a weight display on the scale to the value of the respective test weight according to plus and minus over the entire weighing range. If linearity deviation is discovered during a monitoring of test resources, you can improve this by means of linearization. • • • • Carrying out linearization is restricted to specialist staff possessing well acquainted with the workings of weighing scales.
6. When „L3 1“ is displayed, place the third adjustment weight carefully in the centre of the weighing plate. Enter the desired factor, by which the following adjusting weight is to increase, with the navigation keys. Press the TARE key. 7. Repeat step 6 depending on the number of desired linearization points. The number of desired points of linearization is completed by pressing the BG/ NET key. Confirm with the TARE key, the display returns back to the menu.
Setting "factor” 1 = All weight values are equal 2 = The following weight value is twice as high as the first. 3 = The following weight value is three times higher than the first 4 = ….5 times… 5 = ….6 times… 6 = ….7 times… 7 = ….8 times… 8 = ….9 times… A = ….10 times… B = ….11 times… C = ….12 times… D = ….13 times… E = ….14 times… F = ….
Example 4: 5-point linearization/ 30 kg (5kg, 5kg, 10 kg, 10kg) Display Button Explication 03 CLn TARE Linearization function L0 TARE zero point L11 TARE First adjustment weight (5 kg) L21 TARE Second adjustment weight (5kg), factor 1, i.e., the same size as the first L32 TARE Third adjustment weight (10 kg); factor 2, i.e. twice as high as the first L42 L51 Fourth adjustment weight (10 kg); factor 2, i.e.
19.3 Adjustment of "verified weighing systems / menu block • • " Prepare the required adjustment weight. The weight to be used depends on the capacity of the scale. Carry out adjustment as near as possible to the scale’s maximum weight. Info about test weights can be found on the Internet at: http://www.kern-sohn.com. Observe stable environmental conditions. Stabilisation requires a certain warm-up time. Call up the navigation in the menu/ function: Call up function , see chapter 18.
Perform external adjustment / function "CAL 01": Call up function "CAL 01” Press the TARE button, the currently set adjustment weight is displayed. The last digit flashes. To change the adjustment weight select the digit to be changed with BG/ NET key, the active digit flashes. Enter the desired value with the navigation keys. Press the TARE key repeatedly, until "-----“ is indicated. Ensure that there are no objects on the weighing pan. Press the TARE key.
Carefully place the adjusting weight into the centre of the balancing plate and press the TARE key. After successful adjustment, an acoustic signal sounds. Remove the adjustment weight. Press any key, the scale will return to the menu.. With the navigation keys (see chapter 2.1.1) select "CSP 00". Confirm with TARE key. To exit the menu, move the adjustment switch into the „LOCK” position, see chapter 18.
19.4 Amend the local gravitation zone/ menu block Call up function , see chapter 18. Press TARE key The current setting will be displayed. Using the navigation buttons, enter the local gravitational zone. Confirm with the TARE key, the display returns back to the menu. To exit the menu, move the adjustment switch into the „LOCK“ position, see chapter 18.
19.5 Appliance settings/ menu block Call up the navigation in the menu/ function: Call up function , see chapter 18. Press TARE key Using the navigation keys, select function, (CFn 00 CFn 06) Back to menu: Select function "CFn 00" and confirm with the TARE key.
19.5.1 Parameter „adjustment to site conditions“ (function „CFn 01”) In the case of change to the settings in CFn 01 the settings in FNC 05 are automatically overwritten, see chapter 10.5. Call up function „CFn 01“, see chapter 18.5. Press the TARE-key, current setting appears. Select desired settings with TARE or UNIT key. Zero 0 Zero 9 Switch Automatic zero-adjusting switch on and off and select zero range.
FiL 0 FiL 9 The higher the value, the more priority is given to stability. You can select 0 - 9. Factory setting "0". Confirm with the TARE key, the current response level is displayed. 3 db 0 The higher the value, the more priority is given to response. You can select 0-9. Factory setting "5".
Confirm with the TARE key, the display returns back to the menu. With the navigation keys (see chapter 2.1.1) Select "CFn 00". Confirm with TARE key. To exit the menu, move the adjustment switch into the „LOCK“ position, see chapter 18.
19.5.2 Configuration „verified/ unverified“ (function „CFn 02“) Call up function „CFn 02“, see chapter 18. Press the TARE-key, current setting appears. With the navigation keys (see chapter 2.1.1) select the desired setting. 0⇒ Non verified models 1⇒ Verified models: 2⇒ 7⇒ Not documented Confirm with the TARE key, the display returns back to the menu. With the navigation keys (see chapter 2.1.1) Select "CFn 00". Confirm with TARE key.
19.5.3 Resetting to zero when switched on (function "CFn 04“) Call up function „CFn 04“, see chapter 18. Press the TARE-key, current setting appears. With the navigation keys (see chapter 2.1.1) select the desired setting. 0⇒ 1⇒ 2⇒ 3⇒ 4⇒ 5⇒ 6⇒ 7⇒ 8⇒ 9⇒ Zero setting when switching on within ± 10 % Max. Factory setting verified models (CFn 02 = 1) Zero setting when switching on within ± 20 % Max. Zero setting when switching on within ± 30 % Max. Zero setting when switching on within ± 40 % Max.
19.5.4 Amend the DATA Hold function of verified weighing system (function „CFn 05“) Call up function „CFn 05“, see chapter 18. Press the TARE-key, current setting appears. Select desired settings with TARE or UNIT key. hold 0 Function switched off (factory setting) hold 1 Peak value function This function indicates the highest load factor (peak value) of a continuously rising load. The peak value remains in the display until it is deleted with any key.
Confirm with the TARE key, the display returns back to the menu. With the navigation keys (see chapter 2.1.1) Select "CFn 00". Confirm with TARE key. To exit the menu, move the adjustment switch into the „LOCK“ position, see chapter 18.
19.5.5 Auto zero (verified weighing systems)/ function "CFn 06“ Call up function „CFn 05“, see chapter 18. Press the TARE-key, current setting appears. Select desired settings with TARE or UNIT key. off Function switched off on When the balance is cleared the zero point is corrected automatically. Confirm with the TARE key, the display returns back to the menu. To exit the menu, move the adjustment switch into the „LOCK“ position, see chapter 18.
