KETILER ® OUTDOOR FOOSBALL TABLE MODEL 7399-600 Adult Assembly Required Made in Italy KETILER® International Inc. • 1355 London Bridge Road • Virginia Beach, VA 23453 USA www.kettlerusa.com info@kettlerusa.com Please do not retu m this product to the store. Contact KErrllER® for parts and service: call tolll free 866.804.0440 ,or send emaill to parts@lkefflerusa.com. [Z][]aJATTENTION: KETI1.
Before assembling or using the foosball table, please read the following instructions carefully. They contain important information for use and maintenance of the equipment as well as for your personal safety. Keep these instructions in a safe place for maintenance purposes or for ordering spare parts. All KETTLER® products are designed in accordance with the latest safety regulations and undergo a constant process of quality control during manufacturing.
Before Assembly (continued) General Assembly Instructions • The equipment must be assembled with care by two adults. • Separate all the parts including the hardware. Compare quantities with the package contents section and that all items are undamaged. If there are any problems, please contact KETTLER®. • Before assembling the equipment, study the drawings and photos carefully then assemble in the order shown.
Package Cont ents (continued) 1 Number lncluded-8 (M8x40 Carriage Bolt) Number lncluded-8 Number lncluded-8 (M8 Hexflange nut) Number lncluded-6 Number lncluded-44 (M2.8 X 11.5 Screw) {M4 X 25 Screw) Number lncluded-8 Number lncluded lOx Color 1 lOx Color 2 Number lncluded-4 (M3.9X35 Screw) Number lncluded-4 � Maycome assembled as one piece or separatelyas two pieces. Number lncluded1 Set Color 1 1 Set Color 2 .
r Step 1 2 each required Leg Assembly 1 required 1 required 1 required A Place legs inside cabinet. B Ensure holes in side of cabinet align with holes in leg. Install large resin washers and carriage bolts from the outside in towards leg.(B) C Using hammer, lightly tap bolt heads into side(C), ensuring they are flush with the large washer.
Assembly Step 1 (continued) D Place hexflange nuts onto carriage bolt ends and tighten. E Screw floor leveler into leg post. REPEAT STEP 1 A-G FOR EACH LEG Assembly Pictures Similar Step 2 IMPORTANT: Have two people complete Step 2. Setting the table upright Turn the table onto its feet to prepare for the next assembly step. Warning: This is a heavy product. Do not attempt to move or maneuver without adequate help and safety measures. May result in injury.
REPEAT STEP 3 A-C FOR EACH ROD AS SHOWN BELOW Use the diagram on Page 6 for additional assistance.
Step 4 Rod Bushing Assembly 8 required 16 required M4 X 25 May be necessary to complete before proceeding with Step 4 8 required Insert the 2 part inner bushing in the open cabinet hole (which has the rod extending through) as shown. (A, B) Ensure that it is flush with the inside of the cabinet wall. (C) Install the outer bushing with pins on the outside of cabinet, lining it up with pins from inner bushing. (D) Ensure that it is flush with the outside of the cabinet wall.
Step 4 Rod Bushing Assembly (Continued) Using 2 of the M4 x 25 screws, fasten the bushing into place.
Step 5 Rod Bearing Assembly 8 required 8 required 16 required M4 x 25 On the opposite cabinet hole, slide bearing over the end of rod. (A,B) Insert the end cap into hole. (C) Ensure that it is flush with the cabinet’s wall. (D) Using two M4x25 screws, fasten the end cap into place.
Step 7 Ball Drop Assembly 3 required M2.8 x 11.5 1 required Locate the ball drop assembly hole on the side of cabinet wall. It will be directly in the middle of table and will have 3 punched pilot holes surrounding it. (A) Place ball drop into the hole. (B) Ensure that the screw holes align with the pilot holes. (C) Using three M2.8 x 11.5 screws, fasten the ball holder to the table.
Assembly Step8 Counter Assembly 2 required M3.9 X 35 10 required 2 required 1 required Build color 1 and 2 counters. Separate the color 1 and color 2 cubes with screw holes; these need to be installed at each end of the counter rods. Place all like colored cubes on counter rod with cubes having screw holes on each end of both rods. (A, B) Place color 1 counter into slot on shroud behind the color 1 goalie. (C) Using two M3.9x35 screws, fasten the counter to shroud.
FOOSBALL TABLE COVER The foosball table comes with a cover included when purchased. Always cover your foosball table when not using. This protects the table from the elements and increases the life of the product to provide many years of enjoyment! The cover is equipped with a Velcro side opening for ease of use and a tie down to ensure that the cover stays in place.
This KETTLER® Limited Warranty applies to products sold through the KETTLER® Authorized Dealer Network to the original retail purchaser and authenticated by proof of purchase from a retailer located in the United States. Any shipments made under this warranty will be shipped to the United States only. Any shipment outside of the United States will be at the sole cost of the customer.
Log onto www.kettlerusa.com/warranty and register your KETTLER® Foosball Table Warranty online! www.facebook.com/kettlerusa www.youtube.com/kettlerusa twitter.
©2018 KETTLER® All rights reserved. No part of this manual may be reproduced, stored in a retrieval system, or transmitted in any form, or by any means, such as electronic, mechanical, photocopying or otherwise, without the prior written permission of KETTLER®. KETTLER® International Inc., 1355 London Bridge Road, Virginia Beach, VA 23453 USA www.kettlerusa.com • E-mail: info@kettlerusa.com For parts/service: call 866-804-0440 or e-mail parts@kettlerusa.com Docu 8.01.